A Class-AB/D Audio Power Amplifier for Mobile Applications Integrated Into a 2.5G/3G Baseband Processor

A filterless class-AB/D audio power amplifier integrated into a feature-rich 2.5G/3G baseband processor in standard 65-nm CMOS technology is designed for direct battery hookup in mobile phone applications. Circuit techniques are used to overcome the voltage limitations of standard MOS transistors for operation at voltage levels of 2.5-4.8 V. Both amplifiers can drive more than 650 mW into an 8-Omega load with maximum distortion levels of 1% and 5% for class-D and class-AB, respectively, all from a 3.6-V power supply. The achieved power-supply-rejection ratios are 72 and 84 dB, respectively. The mono implementation of both amplifiers together is 0.44 mm(2)

Intrinsic distortion of a fully differential BD-modulated Class-D amplifier with analog feedback

This paper presents a mathematical analysis of a fully differential BD-modulated Class-D amplifier with analog feedback, i.e., one having a bridge-tied-load output configuration with negative feedback and ternary PWM signal. Notwithstanding the highly nonlinear nature of the amplifier's operation, an extremely accurate closed-form expression for the audible output signal is derived and verified based on computer simulations. This expression demonstrates that there exist larger high-order intrinsic distortions (e.g., 5th-order harmonic distortion and intermodulation distortion) for BD-modulation, compared to that for AD-modulation (binary PWM signal). Furthermore, the 3rd-order harmonic distortion has a roughly parabolic response as a function of the magnitude of the input signal and reaches its peak when the modulation index of the input signal is around 0.7. Overall, the BD-modulated Class-D amplifier has a larger intrinsic distortion for small input signal but a smaller intrinsic distortion for large input signal, compared to AD-modulated designs

Analog Single Sideband-Pulse Width Modulation Processor for Parametric Acoustic Arrays

Parametric acoustic arrays are ultrasonic-based loudspeakers that produce highly directive audio. The audio must first be preprocessed and modulated into an ultrasonic carrier before being emitted into the air, where it will self-demodulate in the far field. The resulting audio wave is proportional to the double time-derivative of the square of the modulation envelope. This thesis presents a fully analog processor which encodes the audio into two Pulse Width Modulated (PWM) signals in quadrature phase and sums them together to produce a Single Sideband (SSB) spectrum around the fundamental frequency of the PWM signals. The two signals are modulated between 8% and 24% duty cycle to maintain a quasi-linear relationship between the duty cycle and the output signal level. This also allows the signals to sum without overlapping each other, maintaining a two-level output. The system drives a network of narrowband transducers with a center frequency equal to the PWM fundamental. Because the transducers are voltage driven, they have a bandpass frequency response which behaves as a first-order integrator on the SSB signal, eliminating the need for two integrators in the processor. Results show that the “SSB-PWM” output wave has a consistent 20-30dB difference in magnitude between the upper sideband and lower sideband. In simulation, a single tone test shows higher total harmonic distortion for lower frequencies and higher modulation depth. A two-tone test creates a 2nd order intermodulation term that increases with the frequencies of the input signals

Integrated circuits for efficient power delivery using pulse-width-modulation

Circuits and architectures for efficient power delivery have become crucial in emerging smart systems. Switching power amplifiers (PA) are very attractive for such applications, because they exhibit better efficiency compared to linear PA designs, due to saturated operation. Switching PAs also allow for utilization of deep submicron CMOS technologies, due to which these designs can be easily integrated with digital circuits, and can benefit from process scaling, in performance as well as in area. Pulse-width-modulation (PWM) is commonly used with switching PAs. A PWM signal typically employs a high-frequency switching pulse waveform as a carrier signal, wherein the pulse-width or duty-cycle of each pulse is modulated by a given low-frequency input signal. The carrier frequency can vary from several kHz to GHz, and is typically determined by the target application. In this thesis, efficient power-delivery circuits that use PWM with switching class-D stages are presented. Advanced circuit techniques, as well as architectures for PWM are proposed to enhance efficiency and circumvent the limitations of conventional architectures. A digitally-intensive transmitter using RF-PWM with a class-D PA is described in the first part of the thesis. The use of carrier switching for alleviating the dynamic range limitation that can be observed in classical RF-PWM implementations is introduced. The approach employs the full carrier frequency for half of the amplitude range, and the second harmonic of half of the carrier frequency, for the remainder of the amplitude range. This concept not only allows the transmitter to drive modulated signals with large peak-to-average power ratio (PAPR), but also improves the back-off efficiency due to reduced switching losses in the half carrier-frequency mode. A glitch-free phase selector is proposed that removes the deleterious glitches that can occur at the input data transitions. The phase-selector also prevents D flip-flop setup-and-hold time violations. The transmitter has been implemented in a 130-nm CMOS process. The measured peak output power and power-added-efficiency (PAE) are 25.6 dBm and 34%, respectively. While driving 802.11g 20-MHz 64-QAM OFDM signals, the average measured output power is 18.3 dBm and the PAE is 16%, with an EVM of -25.5 dB. The second part of the thesis describes a high-speed driver that provides a PWM output using a class-D PA. A PLL-based architecture is employed which eliminates the requirement for a precise ramp or triangular signal generator, and a high-speed comparator, which are typically used for PWM generation. Multi-level signaling is proposed to enhance back-off as well as peak efficiency, which is critical for signals with high PAPR. A differential, folded PWM scheme is introduced to achieve highly linear operation. 3-level operation is achieved without the requirement for additional supply source or sink paths, while 5-level operation is achieved with additional supply source and sink paths, compared to 2-level operation. The PWM driver has been implemented in a 130-nm CMOS process and can operate with a switching frequency of 40-to-170 MHz. For 2/3/5-level PA operation, with a 500 kHz sinusoidal input and 60 MHz switching frequency, the measured THD is -61/-62/-53 dB and corresponding efficiency is 71/83/86% with 175/200/220 mW output power level, respectively. Performance has also been verified for 2/3-level PA operation with a high PAPR signal with 500 kHz bandwidth. While intended as a general purpose amplifier, the approach is well-suited for applications such as power-line communications (PLC). The final part of the thesis introduces an efficient buck/buck-boost reconfigurable LED driver that supports PWM and PFM operation. The driver is based on peak current control. Rectified sin as well as sin² functions are employed in the reference signal to improve the power factor (PF) and total harmonic distortion (THD) of the buck and buck-boost converters. The design ensures that the peak of the inductor current maintains a constant level that is invariant for different AC line voltages. The operating mode of the design can be changed between PWM and PFM. The LED driver has been implemented in a 130-nm CMOS process. PF and THD are improved when the proposed reference is employed, and peak PF and lowest THD are 0.995/0.983/0.996 and 7.8/6.2/3.5% for the buck (PWM), buck (PFM), buck-boost (PFM) cases, respectively. The corresponding peak efficiency for the three cases is 88/92/91%, respectively.Electrical and Computer Engineerin

Advances in Solid State Circuit Technologies

This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields