293 research outputs found
Design of a low power switched-capacitor pipeline analog-to-digital converter
An Analog to Digital Converter (ADC) is a circuit which converts an analog signal into digital signal. Real world is analog, and the data processed by the computer or by other signal processing systems is digital. Therefore, the need for ADCs is obvious.
In this thesis, several novel designs used to improve ADCs operation speed and reduce ADC power consumption are proposed. First, a high speed switched source follower (SSF) sample and hold amplifier without feedthrough penalty is implemented and simulated. The SSF sample and hold amplifier can achieve 6 Bit resolution with sampling rate at 10Gs/s.
Second, a novel rail-to-rail time domain comparator used in successive approximation register ADC (SAR ADC) is implemented and simulated. The simulation results show that the proposed SAR ADC can only consume 1.3 muW with a 0.7 V power supply.
Finally, a prototype pipeline ADC is implemented and fabricated in an IBM 90nm CMOS process. The proposed design is validated using measurement on a fabricated silicon IC, and the proposed 10-bit ADC achieves a peak signal-to-noise- and-distortion-ratio (SNDR) of 47 dB. This SNDR translates to a figure of merit (FOM) of 2.6N/conversion-step with a 1.2 V power supply
Recommended from our members
Designs and calibration of delay-line based ADCs
Delay line ADCs become more and more attractive with technology scaling to smaller dimensions with lower voltages. Time domain resolution can be increased by high speed delay cells. A GHz sampling rate can be easily achieved with low power. However, linearity, which has always been an issue, becomes a problem with longer delay lines. Resolutions of reported delay-line ADCs are hardly more than 4 bits with sampling rates of hundreds of MHz. Thus, this dissertation addresses the linearity issue of delay line ADCs.
First, a novel 11-bit hybrid ADC using flash and delay line architectures, where a 4-bit flash ADC is followed by a 7-bit delay-line ADC, is proposed. In this structure, the noise/error of the second stage delay-line ADC is attenuated at the hybrid ADC output, such that the overall performance would not be limited by the poor linearity of the delay-line ADC. The achieved figure of merit (FOM) of 33.8 fJ/conversion-step is competitive with state-of-the-art ADCs. Furthermore, the proposed ADC inherits accuracy and high speed from the flash ADC and the delay-line ADC, respectively. The inherited advantages strongly support the scalability of the proposed ADC to provide a better performance with low power in further scaled fabrication processes.
Second, in order to remove the harmonic distortion of delay-line ADC, we present a technique which extends harmonic distortion correction (HDC) to digitally calibrate a delay-line ADC. In our simulation
results, digital calibration improves SNDR from 25.6 dB to 42.5 dB by averaging sample points, which corresponds to a 0.86 second calibration time.
Last, a multiple-pass delay line ADC is proposed to improve overall ADC performance in terms of speed and resolution. In this structure, a multiple-pass delay cell can be early triggered by the previous cell to increase speed. Also, phase interpolation is used to improve the effective number of bits. The design is designed and simulated in a commercial 40nm process technology. With 500MHz sampling rate, the multiple-pass delay line ADC achieves an SNDR of 37 dB and consumes 4.2 mW, which is competitive with other reported ADCs.Electrical and Computer Engineerin
A 12-bit SAR ADC for a flexible tactile sensor
Successive Approximation Register (SAR) Analog-to-Digital Converters (ADC) are some of the most efficient ADC topologies available, allowing excellent performance values at low power consumption across a wide range of sampling frequencies. The proposed ADC is aimed at a tactile sensor application, requiring a low-noise and lowpower solution. In addition, it should have high SNDR to detect even the weakest signals with precision. This thesis presents a 12-bit 400 kS/s SAR ADC implemented in a 180 nm CMOS technology for such a task. The designed SAR ADC uses a hybrid R-C DAC topology consisting of a chargescaling MSB DAC and a voltage-scaling LSB DAC, allowing a good trade-off between power consumption, layout area and performance while keeping the total DAC capacitance under reasonable values. Bootstrapped switches have been implemented to preserve high-linearity during the sampling period. A double-tail dynamic comparator has been designed to obtain a low-noise measurement while ensuring suitable delay values. Finally, regarding the logic, an asynchronous implementation and the conventional switching algorithm provide a simple but effective solution to supply the digital signals of the design. Pre-layout noise simulations with input frequencies around 200 kHz show SNDR values of 72.07 dB, corresponding to an ENOB of 11.67 bits. The total power consumption is 365 ?W while the Walden and Schreier figure-of-merit (FoM) correspond to values of 275 fJ/conversion and 160 dB, respectively
A 14-bit 250 MS/s IF Sampling Pipelined ADC in 180 nm CMOS Process
This paper presents a 14-bit 250 MS/s ADC fabricated in a 180 nm CMOS process, which aims at optimizing its linearity, operating speed, and power efficiency. The implemented ADC employs an improved SHA with parasitic optimized bootstrapped switches to achieve high sampling linearity over a wide input frequency range. It also explores a dedicated foreground calibration to correct the capacitor mismatches and the gain error of residue amplifier, where a novel configuration scheme with little cost for analog front-end is developed. Moreover, a partial non-overlapping clock scheme associated with a high-speed reference buffer and fast comparators is proposed to maximize the residue settling time. The implemented ADC is measured under different input frequencies with a sampling rate of 250 MS/s and it consumes 300 mW from a 1.8 V supply. For 30 MHz input, the measured SFDR and SNDR of the ADC is 94.7 dB and 68.5 dB, which can remain over 84.3 dB and 65.4 dB for up to 400 MHz. The measured DNL and INL after calibration are optimized to 0.15 LSB and 1.00 LSB, respectively, while the Walden FOM at Nyquist frequency is 0.57 pJ/step
Recommended from our members
Design and implementation of Radix-3/Radix-2 based novel hybrid SAR ADC in scaled CMOS technologies
This thesis focuses on low power and high speed design techniques for successive
approximation register (SAR) analog-to-digital converters (ADCs) in nanoscale
CMOS technologies. SAR ADCsâ speed is limited by the number of bits of
resolution. An N-bit conventional SAR ADC takes N conversion cycles. To speed
up the conversion process, we introduce a radix-3 SAR ADC which can compute
1:6 bits per cycle. To our knowledge, it is the first fully programmable and efficiently
hardware controlled radix-3 SAR ADC. We had to use two comparators per
cycle due to ADC architecture and we proposed a simple calibration scheme for
the comparators. Also, as the architecture of the DAC array is completely different
from the architecture of conventional radix-2 SAR ADCâs DAC arrays, we came up
with an algorithm for calibration of capacitors of the DAC.
Low power SAR ADCs face two major challenges especially at high resolutions:
(1) increased comparator power to suppress the noise, and (2) increased
DAC switching energy due to the large DAC size. Due to our proposed architecture,the radix-3 SAR ADC uses two comparators per cycle and two differential DACs.
To improve the comparatorâs power efficiency, an efficient and low cost calibration
technique has been introduced. It allows a low power and noisy comparator to
achieve high signal-to-noise ratio (SNR).
To improve the DAC switching energy, we introduced a radix-3/radix-2
based novel hybrid SAR ADC. We use two single ended DACs for radix-3 SAR
ADC and these two single ended DACs can be used as one differential DAC for
radix-2 SAR ADC. So, overall, we only have a single DAC as conventional radix-
2 SAR ADC. In addition, a monotonic switching technique is adopted for radix-2
search to reduce the DAC capacitor size and hence, to reduce switching power. It
can reduce the total number of unit capacitors by four times. Our proposed hybrid
SAR ADC can achieve less DAC energy compared to radix-3 and radix-2 SAR
ADCs. Also, to utilize technology scaling, we used the minimum capacitor size
allowed by thermal noise limitations. To achieve high resolution, we introduced
calibration algorithm for the DAC array.
As mentioned earlier, the radix-3 SAR ADC offers higher power than conventional
radix-2 SAR ADC because of simultaneous use of two comparators. In
the proposed hybrid SAR ADC, we will be using radix-3 search for first few MSB
bits. So, the resolution required for radix-3 comparators are much larger than the
LSB value of 10-bit ADC. By implementing calibration of comparators, we can
use low power, high input referred offset and high speed comparators for radix-3
search. Radix-2 search will be used for rest of the bits and the resolution of the
radix-2 comparator has to be less than the required LSB value. So, a high power, low input referred offset and high speed comparator is used for radix-2 search.
Also, we introduced clock gating for comparators. So, radix-3 comparators will not
toggle during radix-2 search and the radix-2 comparators will be inactive during
radix-3 search. By using the aforementioned techniques, the overall comparator
power is definitely less than a radix-3 SAR ADC and comparable to a conventional
radix-2 SAR ADC.
A prototype radix-3/radix-2 based hybrid SAR ADC with the proposed
technique is designed and fabricated in 40nm CMOS technology. It achieves an
SNDR of 56.9 dB and consumes only 0.38 mW power at 30MS/s, leading to a
Walden figure of merit of 21.5 fJ/conv-step.Electrical and Computer Engineerin
Systematic Design Methodology for Successive â Approximation ADCs
Successive â Approximation ADCs are widely used in ultra â low â power applications. This paper describes a systematic design procedure for designing Successive â Approximation ADCs for biomedical sensor nodes. The proposed scheme is adopted in the design of a 12 bit 1 kS/s ADC. Implemented in 65 nm CMOS, the ADC consumes 354 nW at a sampling rate of 1 kS/s operating with 1.2 supply voltage. The achieved ENOB is 11.6, corresponding to a FoM of 114 fJ/conversion â step
Novel techniques for the design and practical realization of switched-capacitor circuits in deep-submicron CMOS technologies
Dissertação apresentada para obtenção do Grau de Doutor em Engenharia Electrotécnica e de
Computadores pela Universidade Nova de Lisboa, Faculdade de CiĂȘncias e TecnologiaSwitches presenting high linearity are more and more required in switched-capacitor circuits,namely in 12 to 16 bits resolution analog-to-digital converters. The CMOS technology evolves continuously towards lower supply voltages and, simultaneously, new design techniques are necessary to fulfill the realization of switches exhibiting a high dynamic range and a distortion compatible with referred resolutions. Moreover, with the continuously
downing of the sizes, the physic constraints of the technology must be considered to avoid the excessive stress of the devices when relatively high voltages are applied to the gates. New switch-linearization techniques, with high reliability, must be necessarily developed and demonstrated in CMOS integrated circuits.
Also, the research of new structures of circuits with switched-capacitor is permanent.
Simplified and efficient structures are mandatory, adequate to the new demands emerging from the proliferation of portable equipments, necessarily with low energy consumption while assuring high performance and multiple functions.
The work reported in this Thesis comprises these two areas. The behavior of the switches
under these new constraints is analyzed, being a new and original solution proposed, in order to maintain the performance. Also, proposals for the application of simpler clock and control schemes are presented, and for the use of open-loop structures and amplifiers with localfeedback.
The results, obtained in laboratory or by simulation, assess the feasibility of the
presented proposals
Implementation of a 200 MSps 12-bit SAR ADC
Analog-to-digital converters (ADCs) with high conversion frequency, often based on pipelined architectures, are used for measuring instruments, wireless communication and video applications. Successive approximation register (SAR) converters offer a compact and power efficient alternative but the conversion speed is typically designed for lower frequencies. In this thesis a low-power 12-bit 200 MSps SAR ADC based on charge redistribution was designed for a 28 nm CMOS technology. The proposed design uses an efficient SAR algorithm (merged capacitor switching procedure) to reduce power consumption due to capacitor charging by 88 % compared to a conventional design, as well as reducing the total capacitor area by half. Sampling switches were bootstrapped for increased linearity compared to simple transmission gates. Another feature of the low power design is a fully-dynamic comparator which does not require a preamplifier. Pre-layout simulations of the SAR ADC with 800 MHz input frequency shows an SNDR of 64.8 dB, corresponding to an ENOB of 10.5, and an SFDR of 75.3 dB. The total power consumption is 1.77 mW with an estimated value of 500 W for the unimplemented digital logic. Calculation of the Schreier figure-of-merit was done with an input signal at the Nyquist frequency. The simulated SNDR, SFDR and power equals 69.5 dB, 77.3 dB and 1.9 mW respectively, corresponding to a figure-of merit of 176.6 dB.FrÄn analogt till digitalt - snabba och strömsnÄla omvandlare Dagens digitala samhÀlle stÀller höga krav pÄ prestanda och effektivitet. I samarbete med Ericsson i Lund har en krets för signalomvandling utvecklats. Genom smart design uppnÄs hög hastighet och lÄg strömförbrukning som ligger i forskningens framkant. FrÄn analogt till digitalt Ett viktigt byggblock för telekommunikation och videoapplikationer Àr sÄ kallade A/D-omvandlare, som översÀtter mellan analoga signaler (till exempel ljud) och digitala signaler bestÄende av ettor och nollor. En vÀldigt effektiv metod för A/D-omvandling bygger pÄ sÄ kallad successiv approximation. Metoden innebÀr att signalen som ska omvandlas jÀmförs med en referensnivÄ, som stegvis justeras för att nÀrma sig signalens vÀrde. Till slut har man en tillrÀckligt god uppskattning av vÀrdet som ska mÀtas. Just en sÄdan omvandlare har utvecklats med höga krav pÄ hastighet och energiförbrukning. Detta gjordes genom datorsimuleringar av modeller som beskriver kretsen. ReferensnivÄn skapas ofta genom att styra ett nÀtverk som lagrar elektrisk laddning. Omvandlingens noggrannhet, eller upplösning, beror pÄ hur mÄnga nivÄer som finns tillgÀngliga det vill sÀga hur nÀra signalens vÀrde man kan komma. I den designade kretsen finns hela 4096 nivÄer! Det finns mÄnga kÀllor till osÀkerhet i systemet, bland annat hur exakta referensnivÄerna Àr och hur bra jÀmförelsen med insignalen kan göras. Eftersom dessa eventuellt kan leda till en försÀmring av omvandlingens noggrannhet mÄste alla delar i kretsen utformas med detta i Ätanke. Höga hastigheter Eftersom det krÀvs mÄnga steg för referensnivÄn att nÀrma sig signalens vÀrde Àr den maximala omvandlingshastigheten ofta begrÀnsad. Med teknikens utveckling öppnas nya möjligheter i takt med att mikrochippens enskilda komponenter blir snabbare. Modern forskning visar att omvandlare baserade pÄ successiv approximation kan uppnÄ hastigheter pÄ flera miljoner mÀtvÀrden varje sekund, vilket Àven den utvecklade kretsen klarar av. Effektiv design Nya metoder för successiv approximation möjliggör stora besparingar nÀr det gÀller effektförbrukning, till exempel genom att effektivisera upp- och urladdningen av nÀtverket. Genom smÄ Àndringar kunde nÀtverkets energiförbrukning minskas med över 90 % samtidigt som dess area halverades. Eftersom produktionskostnaden för integrerade kretsar Àr hög medför varje minskning av kretsens area att kostnaden sjunker
- âŠ