Design of High-Speed and Low-Power Comparator in Flash ADC

AbstractIn this paper, a high-speed low-power comparator, which is used in a 2 Gsps, 8 bit Flash ADC, is designed and simulated. Based on 0.18 um TSMC CMOS process model, the comparator circuit is simulated with a 1.8V power supply in Cadence environment. The result shows that it can work at a 2GHZ clock frequency, and the dynamic power consumption is only 1.2mW, with 123.5ps transmission delay. In addition, the average offset voltage of this comparator is only 676.3uV, which can meet the requirements of an 8-bit Flash ADC

Design and Analysis of a Low-Power 8-Bit 500 KS/S SAR ADC for Bio-Medical Implant Devices

This thesis project involves the design and analysis of an 8-bit Successive Approximation Register (SAR) Analog to Digital Convertor (ADC), designed for low- power applications such as bio-medical implants. The sampling rate for this ADC is 500 KS/s. The power consumption for the whole SAR ADC system was measured to be 2.1 uW. The novelty of this project is the proposal of an extremely energy efficient comparator architecture. The result is the design of a final ADC with reasonable sampling speed, accuracy and low power consumption. In this project, all the different subsystems have been designed at the transistor level with 45 nm CMOS technology. The logical circuit was designed using Verilog language. It was then synthesized and integrated in the overall system

Switched-compensation technique in switched-capacitor circuits for achieving fast settling performance

Resolving stability issue is one of the major challenges in designing a perfect op-amp, the most widely used analog circuit block. Many compensation techniques have been proposed to improve the stability performance of op amps, but virtually all these techniques were developed for continuous-time applications and subsequently applied to discrete-time applications (e.g., switched-capacitor circuits). Since the early 1980s, an increasing number of op-amps have been used in switched-capacitor circuits with no special compensation method applied. Consequently, there remains a need to explore the possibility of designing a unique compensation method specifically for switched-capacitor use. A new switched-compensation technique (SCT) is proposed for switched-capacitor circuit applications in which high speed is a critical index of performance. In general, designers must deal with trade-offs among accuracy, speed, and power dissipation. SCT avoids traditional approaches of designing high-speed, high-gain operational amplifiers that are in many cases technology-limited. Instead, it modifies the switched-capacitor circuit structure to use the under-damped response of the system, usually regarded as a drawback. SCT is introduced as a novel solution for achieving fast settling performance and lower quiescent power dissipation while guaranteeing almost equivalent accuracy. SCT can be easily implemented in flip-around switched-capacitor amplifier circuits. This paper explains SCT principle and implementation applied to multiplying-digital-to-analog converters (MDACs) as a proof of concept. Simulation results based on an IBM 0.13um CMOS process are presented. Compared with a conventional switched-capacitor amplifier, a SCT-based implementation reduces the quiescent power consumption by half and settling time within 1% error by 60%

Development and Analysis of Non-Delay-Line Constant-Fraction Discriminator Timing Circuits, Including a Fully-Monolithic CMOS Implementation

A constant-fraction discriminator (CFD) is a time pick-off circuit providing time derivation that is insensitive to input-signal amplitude and, in some cases, input-signal rise time. CFD time pick-off circuits are useful in Positron Emission Tomography (PET) systems where Bismuth Germanate (BGO)/photomultiplier scintillation detectors detect coincident, 511-keV annihilation gamma rays. Time walk and noise-induced timing jitter in time pick-off circuits are discussed along with optimal and sub-optimal timing filters designed to minimize timing jitter. Additionally, the effects of scintillation-detector statistics on timing performance are discussed, and Monte Carlo analysis is developed to provide estimated timing and energy spectra for selected detector and time pick-off circuit configurations. The traditional delay-line CFD is then described with a discussion of deterministic (non statistical) performance and statistical Monte Carlo timing performance. A new class of non-delay-line CFD circuits utilizing lowpass- and/or allpass-filter delay-line approximations is then presented. The timing performance of these non-delay-line CFD circuits is shown to be comparable to traditional delay-line CFD circuits. Following the development and analysis of non-delay-line CFD circuits, a fully-monolithic, non-delay-line CFD circuit is presented which was fabricated in a standard digital, 2-μ, double-meta], double-poly, n-well CMOS process. The CMOS circuits developed include a low time walk comparator having a time walk of approximately 175 ps for input signals with amplitudes between 10-mV to 2000-mV and a rise time (10 - 90%) of 10 ns. Additionally, a fifth-order, continuous-time filter having a bandwidth of over 100 MHz was developed to provide CFD signal shaping without a delay line. The measured timing resolution (3.26 ns FWITh1, 6.50 ns FWTM) of the fully-monolithic, CMOS CFD is comparable to measured resolution (3.30 ns FWHM, 6.40 ns FWTM) of a commercial, discrete, bipolar CFD containing an external delay line. Each CFD was tested with a PET EGO/photomultiplier scintillation detector and a preamplifier having a 10-ns (10 - 90%) rise-time. The development of a fully-monolithic, CMOS CFD circuit, believed to be the first such reported development, is significant for PET and other systems that employ many front-end CFD time pick-off circuits

Digital Background Self-Calibration Technique for Compensating Transition Offsets in Reference-less Flash ADCs

This Dissertation focusses on proving that background calibration using adaptive algorithms are low-cost, stable and effective methods for obtaining high accuracy in flash A/D converters. An integrated reference-less 3-bit flash ADC circuit has been successfully designed and taped out in UMC 180 nm CMOS technology in order to prove the efficiency of our proposed background calibration. References for ADC transitions have been virtually implemented built-in in the comparators dynamic-latch topology by a controlled mismatch added to each comparator input front-end. An external very simple DAC block (calibration bank) allows control the quantity of mismatch added in each comparator front-end and, therefore, compensate the offset of its effective transition with respect to the nominal value. In order to assist to the estimation of the offset of the prototype comparators, an auxiliary A/D converter with higher resolution and lower conversion speed than the flash ADC is used: a 6-bit capacitive-DAC SAR type. Special care in synchronization of analogue sampling instant in both ADCs has been taken into account. In this thesis, a criterion to identify the optimum parameters of the flash ADC design with adaptive background calibration has been set. With this criterion, the best choice for dynamic latch architecture, calibration bank resolution and flash ADC resolution are selected. The performance of the calibration algorithm have been tested, providing great programmability to the digital processor that implements the algorithm, allowing to choose the algorithm limits, accuracy and quantization errors in the arithmetic. Further, systematic controlled offset can be forced in the comparators of the flash ADC in order to have a more exhaustive test of calibration

A High-Speed and Low-Offset Dynamic Latch Comparator

Circuit intricacy, speed, low-offset voltage, and resolution are essential factors for high-speed applications like analog-to-digital converters (ADCs). The comparator circuit with preamplifier increases the power dissipation, as it requires higher amount of currents than the latch circuitry. In this research, a novel topology of dynamic latch comparator is illustrated, which is able to provide high speed, low offset, and high resolution. Moreover, the circuit is able to reduce the power dissipation as the topology is based on latch circuitry. The cross-coupled circuit mechanism with the regenerative latch is employed for enhancing the dynamic latch comparator performance. In addition, input-tracking phase is used to reduce the offset voltage. The Monte-Carlo simulation results for the designed comparator in 0.18 μm CMOS process show that the equivalent input-referred offset voltage is 720 μV with 3.44 mV standard deviation. The simulated result shows that the designed comparator has 8-bit resolution and dissipates 158.5 μW of power under 1.8 V supply while operating with a clock frequency of 50 MHz. In addition, the proposed dynamic latch comparator has a layout size of 148.80 μm×59.70 μm

Proposed 10-bit 1 Ghz Two-step Analog to Digital Converter for Implementation in Tfsoi

School of Electrical and Computer Engineerin

Design of 10 Gb/s burst-mode receivers for high-split extended reach PONs

The continuous stream of new applications for the internet, increases the need for higher access speed in the currently deployed communication networks. Most networks in use today still consist of twisted copper wires, inherited from the telephone network. The disadvantages of reusing the existing telephone network are twofold. Firstly, the bandwidth of twisted copper wires is limited and secondly, a large number of switches and routers are needed throughout the network leading to an excessive power consumption. The hybrid fiber coax network that reuses the television distribution network is not free from these drawbacks. The bandwidth is also limited and power hungry amplifiers are needed to bridge the distance to and from the user. The future of broadband access lies in optical fiber networks. The optical fiber has a virtually unlimited bandwidth and the lower attenuation leads to less switches and amplifiers in the network, reducing the power consumption of the complete infrastructure. This dissertation describes the design of a 10 Gb/s burst-mode receiver for high-split extended reach passive optical networks (PONs). The designed receiver incorporates two very advanced features. Firstly, the burst-mode receiver locks its gain setting within 6 ns avoiding packet loss due to gain switching during data payload reception. Secondly, the burst-mode receiver detects both burst start and burst end, making it the first burst-mode receiver of its kind to operate without any time critical signal requirements from outside the burst-mode receiver. The presented work covers the chip-level architecture study and design of a 10 Gb/s burst-mode transimpedance amplifier and a 10 Gb/s post-amplifier, which are the two most critical components of a burst-mode receiver

Development of a 6-bit 15.625 MHz CMOS two-step flash analog-to-digital converter for a low dead time sub-nanosecond time measurement system

The development of a 6-bit 15.625 MHz CMOS two-step analog-to-digital converter (ADC) is presented. The ADC was developed for use in a low dead time, high-performance, sub-nanosecond time-to-digital converter (TDC). The TDC is part of a new custom CMOS application specific integrated circuit (ASIC) that will be incorporated in the next generation of front-end electronics for high-performance positron emission tomography imaging. The ADC is based upon a two-step flash architecture that reduces the comparator count by a factor-of-two when compared to a traditional flash ADC architecture and thus a significant reduction in area, power dissipation, and input capacitance of the converter is achieved. The converter contains time-interleaved auto-zeroed CMOS comparators. These comparators utilize offset correction in both the preamplifier and the subsequent regenerative latch stage to guarantee good integral and differential non-linearity performance of the converter over extreme process conditions. Also, digital error correction was employed to overcome most of the major metastability problems inherent in flash converters and to guarantee a completely monotonic transfer function. Corrected comparator offset measurements reveal that the CMOS comparator design maintains a worse case input-referred offset of less than 1 mV at conversion rates up to 8 MHz and less than a 2 mV offset at conversion rates as high as 16 MHz while dissipating less than 2.6 mW. Extensive laboratory measurements indicate that the ADC achieves differential and integral non-linearity performance of less than ±1/2 LSB with a 20 mV/LSB resolution. The ADC dissipates 90 mW from a single 5 V supply and occupies a die area of 1.97 mm x 1.13 mm in 0.8 μm CMOS technology

Characterization of optical interconnects

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2000.Includes bibliographical references (p. 72-75).Interconnect has become a major issue in deep sub-micron technology. Even with copper and low-k dielectrics, parasitic effects of interconnects will eventually impede advances in integrated electronics. One technique that has the potential to provide a paradigm shift is optics. This project evaluates the feasibility of optical interconnects for distributing data and clock signals. In adopting this scheme, variation is introduced by the detector, the waveguides, and the optoelectronic circuit, which includes device, power supply and temperature variations. We attempt to characterize the effects of the aforementioned sources of variation by designing a baseline optoelectronic circuitry and fabricating a test chip which consists of the circuitry and detectors. Simulations are also performed to supplement the effort. The results are compared with the performance of traditional metal interconnects. The feasibility of optical interconnects is found to be sensitive to the optoelectronic circuitry used. Variation effects from the devices and operating conditions have profound impact on the performance of optical interconnects since they introduce substantial skew and delay in the otherwise ideal system.by Shiou Lin Sam.S.M