CMOS RF front-end design for terrestrial and mobile digital television systems

With the increasing demand for high quality TV service, digital television (DTV) is replacing the conventional analog television. DTV tuner is one of the most critical blocks of the DTV receiver system; it down-converts the desired DTV RF channel to baseband or a low intermediate frequency with enough quality. This research is mainly focused on the analysis and realization of low-cost low-power front-ends for ATSC terrestrial DTV and DVB-H mobile DTV tuner systems. For the design of the ATSC terrestrial tuner, a novel double quadrature tuner architecture, which can not only minimize the tuner power consumption but also achieve the fully integration, has been proposed. A double quadrature down-converter has been designed and fabricated with TSMC 0.35õm CMOS technology; the measurement results verified the proposed concepts. For the mobile DTV tuner, a zero-IF architecture is used and it can achieve the DVB-H specifications with less than 200mW power consumption. In the implementation of the mobile DVB-H tuner, a novel RF variable gain amplifier (RFVGA) and a low flicker noise current-mode passive mixer have been proposed. The proposed RFVGA achieves high dynamic range and robust input impedance matching performance, which is the main design challenge for the traditional implementations. The current-mode passive mixer achieves high-gain, low noise (especially low flicker noise) and high-linearity (over 10dBm IIP3) with low power supplies; it is believed that this is a promising topology for low voltage high dynamic range mixer applications. The RFVGA has been fabricated in TSMC 0.18õm CMOS technology and the measurement results agree well with the theoretical ones

Digitally-Enhanced Software-Defined Radio Receiver Robust to Out-of-Band Interference

A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband in combination with low-pass filtering to mitigate blockers and improve out-of-band IIP3. Two alternative “iterative” harmonic-rejection (HR) techniques are presented to achieve high HR robust to mismatch: a) an analog two-stage polyphase HR concept, which enhances the HR to more than 60 dB; b) a digital adaptive interference cancelling (AIC) technique, which can suppress one dominating harmonic by at least 80 dB. An accurate multiphase clock generator is presented for a mismatch-robust HR. A proof-of-concept receiver is implemented in 65 nm CMOS. Measurements show 34 dB gain, 4 dB NF, and 3.5 dBm in-band IIP3 while the out-of-band IIP3 is + 16 dBm without fine tuning. The measured RF bandwidth is up to 6 GHz and the 8-phase LO works up to 0.9 GHz (master clock up to 7.2 GHz). At 0.8 GHz LO, the analog two-stage polyphase HR achieves a second to sixth order HR > dB over 40 chips, while the digital AIC technique achieves HR > 80 dB for the dominating harmonic. The total power consumption is 50 mA from a 1.2 V supply

Flexible Receivers in CMOS for Wireless Communication

Consumers are pushing for higher data rates to support more services that are introduced in mobile applications. As an example, a few years ago video-on-demand was only accessed through landlines, but today wireless devices are frequently used to stream video. To support this, more flexible network solutions have merged in 4G, introducing new technical problems to the mobile terminal. New techniques are thus needed, and this dissertation explores five different ideas for receiver front-ends, that are cost-efficient and flexible both in performance and operating frequency. All ideas have been implemented in chips fabricated in 65 nm CMOS technology and verified by measurements. Paper I explores a voltage-mode receiver front-end where sub-threshold positive feedback transistors are introduced to increase the linearity in combination with a bootstrapped passive mixer. Paper II builds on the idea of 8-phase harmonic rejection, but simplifies it to a 6-phase solution that can reject noise and interferers at the 3rd order harmonic of the local oscillator frequency. This provides a good trade-off between the traditional quadrature mixer and the 8- phase harmonic rejection mixer. Furthermore, a very compact inductor-less low noise amplifier is introduced. Paper III investigates the use of global negative feedback in a receiver front-end, and also introduces an auxiliary path that can cancel noise from the main path. In paper IV, another global feedback based receiver front-end is designed, but with positive feedback instead of negative. By introducing global positive feedback, the resistance of the transistors in a passive mixer-first receiver front-end can be reduced to achieve a lower noise figure, while still maintaining input matching. Finally, paper V introduces a full receiver chain with a single-ended to differential LNA, current-mode downconversion mixers, and a baseband circuity that merges the functionalities of the transimpedance amplifier, channel-select filter, and analog-to-digital converter into one single power-efficient block

Broadband RF Front-End Design for Multi-Standard Receiver with High-Linearity and Low-Noise Techniques

Future wireless communication devices must support multiple standards and features on a single-chip. The trend towards software-defined radio requires flexible and efficient RF building blocks which justifies the adoption of broadband receiver front-ends in modern and future communication systems. The broadband receiver front-end significantly reduces cost, area, pins, and power, and can process several signal channels simultaneously. This research is mainly focused on the analysis and realization of the broadband receiver architecture and its various building blocks (LNA, Active Balun-LNA, Mixer, and trans-impedance amplifier) for multi-standard applications. In the design of the mobile DTV tuner, a direct-conversion receiver architecture is adopted achieving low power, low cost, and high dynamic-range for DVB-H standard. The tuner integrates a single-ended RF variable gain amplifier (RFVGA), a current-mode passive mixer, and a combination of continuous and discrete-time baseband filter with built-in anti-aliasing. The proposed RFVGA achieves high dynamic-range and gain-insensitive input impedance matching performance. The current-mode passive mixer achieves high gain, low noise, and high linearity with low power supplies. A wideband common-gate LNA is presented that overcomes the fundamental trade-off between power and noise match without compromising its stability. The proposed architecture can achieve the minimum noise figure over the previously reported feedback amplifiers in common-gate configuration. The proposed architecture achieves broadband impedance matching, low noise, large gain, enhanced linearity, and wide bandwidth concurrently by employing an efficient and reliable dual negative-feedback. For the wideband Inductorless Balun-LNA, active single-to-differential architecture has been proposed without using any passive inductor on-chip which occupies a lot of silicon area. The proposed Balun-LNA features lower power, wider bandwidth, and better gain and phase balance than previously reported architectures of the same kind. A surface acoustic wave (SAW)-less direct conversion receiver targeted for multistandard applications is proposed and fabricated with TSMC 0.13?m complementary metal-oxide-semiconductor (CMOS) technology. The target is to design a wideband SAW-less direct coversion receiver with a single low noise transconductor and current-mode passive mixer with trans-impedance amplifier utilizing feed-forward compensation. The innovations in the circuit and architecture improves the receiver dynamic range enabling highly linear direct-conversion CMOS front-end for a multi-standard receiver

Subthreshold 3 Phase Mixers

This thesis will discuss subthreshold FET mixers with a focus on conversion loss derivations. To begin understanding the mixers, a look into the FET model is first taken in Chapter II. Then in Chapter III, a single FET device mixer is studied and its conversion loss is found from its small-signal model. The chapter will then include a two FET device mixer and a four device FET mixer. Finally a new type of mixer will be discussed in Chapter IV. The new type of mixer is a 3 phase mixer with the phase angles being 0°, 120°, and 240°. The theoretical conversion loss is found by treating the FETs as simple switches and a square wave as the RF signal. The resulting conversion loss is shown to be better than the previous mixers mentioned. The thesis will conclude with a discussion of future areas of work for the mixer

Novel RF CMOS Integrated Circuits and Systems for Broadband Dielectric Spectroscopy

Broadband dielectric spectroscopy has proven to be a valuable technique for characterization of chemicals and biomaterials. It has the great potential to become an indispensable and cost-effective tool in point-of-care medical applications due to its label-free and non-invasive operation. However, most of the existing dielectric spectroscopy instruments require bulky, heavy and expensive measurement set-up, restricting their use to only special applications in industry and laboratories. Therefore, integrated dielectric spectroscopy on silicon capable of direct detection of chemicals/biomaterials' complex permittivity can yield significant cost and size reduction, system integration, portability, enormous processing, and high throughput. A CMOS wideband dielectric spectroscopy system is proposed for chemical and biological material characterization. The complex permittivity detection is performed using a configurable harmonic-rejecting receiver capable of indirectly measuring the complex admittance of sensing capacitor exposed to the material-under-test (MUT) and subject to RF signal excitation with a frequency range of 0.62-10 GHz. The sensing capacitor is embedded in a voltage divider topology with a fixed capacitor and the relative variations in the magnitude and phase of the voltages across the capacitors are used to find the real and imaginary parts of the permittivity. The sensor achieves an rms permittivity error of less than 1% over the entire operation bandwidth. Using a sub-harmonic mixing scheme, the system can perform complex permittivity measurements from 0.62 to 10 GHz while requiring an input signal source with frequency range of only from 5 to 10 GHz. Thereby, the permittivity measurement system can be easily made self-sustained by implementing a 5-10 GHz frequency synthesizer on the same chip. One of the key building blocks in such a frequency synthesizer is the voltage-controlled oscillator (VCO) which has to cover an octave of frequency range. A novel low-phase-noise wide-tuning range VCO is presented using a triple-band LC resonator. The implemented VCO in 0.18μm CMOS technology achieves a continuous tuning range of 86.7% from 5.12 GHz to 12.95 GHz while drawing 5 to 10 mA current from 1-V supply. The measured phase noise at 1 MHz offset from carrier frequencies of 5.9, 9.12 and 12.25 GHz is -122.9, -117.1 and -110.5 dBc/Hz, respectively. Also, a dual-band quadrature voltage-controlled oscillator (QVCO) is presented using a transformer-based high-order LC-ring resonator which inherently provides quadrature signals without requiring noisy coupling transistors as in traditional approaches. The proposed resonator shows two possible oscillation frequencies which are exploited to realize a wide-tuning range QVCO employing a mode-switching transistor network. Due to the use of transformers, the oscillator has minimal area penalty compared to the conventional designs. The implemented prototype in a 65-nm CMOS process achieves a continuous tuning range of 77.8% from 2.75 GHz to 6.25 GHz while consuming 9.7 to 15.6 mA current from 0.6-V supply. The measured phase noise figure-of-merit (FoM) at 1 MHz offset ranges from 184 dB to 188.2 dB throughout the entire tuning range. The QVCO also exhibits good quadrature accuracy with 1.5º maximum phase error and occupies a relatively small silicon area of 0.35 mm^2

Analog Baseband Filters and Mixed Signal Circuits for Broadband Receiver Systems

Data transfer rates of communication systems continue to rise fueled by aggressive demand for voice, video and Internet data. Device scaling enabled by modern lithography has paved way for System-on-Chip solutions integrating compute intensive digital signal processing. This trend coupled with demand for low power, battery-operated consumer devices offers extensive research opportunities in analog and mixed-signal designs that enable modern communication systems. The first part of the research deals with broadband wireless receivers. With an objective to gain insight, we quantify the impact of undesired out-band blockers on analog baseband in a broadband radio. We present a systematic evaluation of the dynamic range requirements at the baseband and A/D conversion boundary. A prototype UHF receiver designed using RFCMOS 0.18[mu]m technology to support this research integrates a hybrid continuous- and discrete-time analog baseband along with the RF front-end. The chip consumes 120mW from a 1.8V/2.5V dual supply and achieves a noise figure of 7.9dB, an IIP3 of -8dBm (+2dbm) at maximum gain (at 9dB RF attenuation). High linearity active RC filters are indispensable in wireless radios. A novel feed-forward OTA applicable to active RC filters in analog baseband is presented. Simulation results from the chip prototype designed in RFCMOS 0.18[mu]m technology show an improvement in the out-band linearity performance that translates to increased dynamic range in the presence of strong adjacent blockers. The second part of the research presents an adaptive clock-recovery system suitable for high-speed wireline transceivers. The main objective is to improve the jitter-tracking and jitter-filtering trade-off in serial link clock-recovery applications. A digital state-machine that enables the proposed mixed-signal adaptation solution to achieve this objective is presented. The advantages of the proposed mixed-signal solution operating at 10Gb/s are supported by experimental results from the prototype in RFCMOS 0.18[mu]m technology

Direct sampling receivers for broadband communications

Today everything tends to be connected in the Internet of Things (IoT) universe, where a broad variety of communication standards and technologies are used for those connected devices. It is always a dream to design a Software-Defined Radio (SDR) supporting different standards solely based on the software configuration. As integrated-circuit (IC) manufacture and design advance, a partial of SDR can be realized. This thesis investigates one of the most important parts in a SDR: the analog design of a direct sampling (DS) receiver, which mainly consists of a broadband RF front end and a wideband ADC. Especially, a DS receiver shows a great flexibility and efficiency for the simultaneous reception of multiple channels comparing with the traditional parallelism of superheterodyne structure. The research contributions of this work include (1) demonstration and comparative analysis of two new architectures of broadband RFPGAs: voltage-mode: RFPGA-V and current-mode: RFPGA-I. RFPGA-V and RFPGA-I utilize an innovative interpolation method and current steering approach, respectively, to achieve a fine gain step of 0.25-dB over 40-dB gain range for several GHz frequency range. Besides, with innovative design, no off-chip inductor is needed for the both RFPGAs. (2) The design of a 5-GS/s 10b time-interleaved SAR. The ADC power efficiency is significantly improved by many design techniques: the low-energy CDAC switching scheme, optimized input common-mode voltage for comparator, optimal reduced radix-2 capacitor ratio for low-power reference buffers and higher conversion speed, etc. The lane-to-lane mismatches in a time-interleave ADC are minimized by using optimal floor plan and then are calibrated digitally. Three prototypes: the broadband RF front ends with RFPGA-V, the broadband RF front ends with RFPGA-I and a 5-GHz ADC, are fabricated to verify the proposed ideas in 28nm CMOS technology.Electrical and Computer Engineerin