A Single-Stage LED Driver Based on ZCDS Class-E Current-Driven Rectifier as a PFC for Street-Lighting Applications

This paper presents a light-emitting diode (LED) driver for street-lighting applications that uses a resonant rectifier as a power-factor corrector (PFC). The PFC semistage is based on a zero-current and zero-derivative-switching (ZCDS) Class-E current-driven rectifier, and the LED driver semistage is based on a zero-voltage-switching (ZVS) Class-D LLC resonant converter that is integrated into a single-stage topology. To increase the conduction angle of the bridge-rectifier diodes current and to decrease the current harmonics that are injected in the utility line, the ZCDS Class-E rectifier is placed between the bridge-rectifier and a dc-link capacitor. The ZCDS Class-E rectifieris driven by a high-frequency current source, which is obtained from a square-wave output voltage of the ZVS Class-D LLC resonant converter using a matching network. Additionally, the proposed converter has a soft-switching characteristic that reduces switching losses and switching noise. A prototype for a 150-W LED street light has been developed and tested to evaluate the performance of the proposed approach. The proposed LED driver had a high efficiency (>91%), a high PF (>0.99), and a low total harmonic distortion (THD i <; 8%) under variation of the utility-line input voltage from 180 to 250 V rms . These experimental results demonstrate the feasibility of the proposed LED scheme

Optimized design of a high input-voltage-ripple-rejection converter for LED lighting

The asymmetrical half-bridge (AHB) converter has been deeply analyzed as second stage in ac–dc light emitting diode (LED) drivers. Galvanic isolation, high reliability and high efficiency are their main advantages while a limited duty cycle range (i.e., 0–0.5) and a poor dynamic behavior are their main disadvantages. As second stage of an LED driver, the most demanding requirement for its control loop is cancelling the low-frequency ripple introduced by the first stage. According to its limited maximum attainable bandwidth, this is normally achieved by implementing a feedforward loop. Nonetheless, the static gain of the standard AHB converter presents a nonlinear relation between the output voltage and the duty cycle. As a consequence, the effectiveness of this feedforward loop is limited. In this paper, the use of the zeta AHB converter as second stage of an LED driver is analyzed and an optimized design is proposed. Regarding its advantages, it presents an extended duty cycle range (theoretically, 0–1.0). Besides, it presents a linear relation between the output voltage and the duty cycle. Therefore, although its dynamic behavior is still limited, it can perfectly cancel the low-frequency ripple introduced by the first stage of the LED driver by means of a straightforward feedforward loop. The optimized design proposed in this paper is focused on minimizing the losses in the magnetic components (transformer and inductor) by wisely choosing the value of the two turns ratios of the transforme

Multiple-output DC–DC converters: applications and solutions

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required. The interest and importance of this type of multiport configuration is also reflected in that many electronics manufacturers currently develop integrated solutions. Traditionally, the different output voltages required are obtained by means of a transformer with several windings, which are in addition to providing electrical isolation. However, the current trend in the development of multiple-output DC–DC converters follows general aspects, such as low losses, high-power density, and high efficiency, as well as the development of new architectures and control strategies. Certainly, simple structures with a reduced number of components and power switches will be one of the new trends, especially to reduce the size. In this sense, the incorporation of devices with a Wide Band Gap (WBG), particularly Gallium Nitride (GaN) and Silicon Carbide (SiC), will establish future trends, advantages, and disadvantages in the development and applications of multiple-output DC–DC converters. In this paper, we present a review of the most important topics related to multiple-output DC–DC converters based on their main topologies and configurations, applications, solutions, and trends. A wide variety of configurations and topologies of multiple-output DC–DC converters are shown (more than 30), isolated and non-isolated, single and multiple switches, and based on soft and hard switching techniques, which are used in many different applications and solutions.info:eu-repo/semantics/publishedVersio