펄스 기반 피드 포워드 이퀄라이저를 갖춘 고용량 DRAM을 위한 컨트롤러 PHY 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2020. 8. 김수환.A controller PHY for managed DRAM solution, which is a new memory structure to maximize capacity while minimizing refresh power, is presented. Inter-symbol interference is critical in such a high-capacity DRAM interface in which many DRAM chips share a command/address (C/A) channel. A pulse-based feed-forward equalizer (PB-FFE) is introduced to reduce ISI on a C/A channel. The controller PHY supports all the training sequences specified in the DDR4 standard. A glitch-free DCDL is also adopted to perform link training efficiently and to reduce training time. The DQ transmitter adopts quarter-rate architecture to reduce output latency. For the quarter-rate transmitters in DQ, we propose a quadrature error corrector (QEC), in which clock signal phase errors are corrected using two replicas of the 4:1 serializer of the output stage. Pulse shrinking is used to compare and equalize the outputs of these two replica serializers. A controller PHY was fabricated in 55nm CMOS. The PB-FFE increases the timing margin from 0.23UI to 0.29UI at 1067Mbps. At 2133Mbps, the read timing and voltage margins are 0.53UI and 211mV after read training, and the write margins are 0.72UI and 230mV after write training. To validate the QEC effectiveness, a prototype quarter-rate transmitter, including the QEC, was fabricated to another chip in 65nm CMOS. Adopting our QEC, the experimental results show that the output phase errors of the transmitter are reduced to a residual error of 0.8ps, and the output eye width and height are improved by 84% and 61%, respectively, at a data-rate of 12.8Gbps.본 연구에서 용량을 최대화하면서도 리프레시 전력을 최소화할 수 있는 새로운 메모리 구조인 관리형 DRAM 솔루션을 위한 컨트롤러 PHY를 제시하였다. 이와 같은 고용량 DRAM 인터페이스에서는 많은 DRAM 칩이 명령 / 주소 (C/A) 채널을 공유하고 있어서 심볼 간 간섭이 발생한다. 본 연구에서는 이러한 C/A 채널에서의 심볼 간 간섭을 줄이기 위해 펄스 기반 피드 포워드 이퀄라이저 (PB-FFE)를 채택하였다. 또한 본 연구의 컨트롤러 PHY는 DDR4 표준에 지정된 모든 트레이닝 시퀀스를 지원한다. 링크 트레이닝을 효율적으로 수행하고 트레이닝 시간을 줄이기 위해 글리치가 발생하지 않는 디지털 제어 지연 라인 (DCDL)을 채택하였다. 컨트롤러 PHY의 DQ 송신기는 출력 대기 시간을 줄이기 위해 쿼터 레이트 구조를 채택하였다. 쿼터 레이트 송신기의 경우에는 직교 클럭 간 위상 오류가 출력 신호의 무결성에 영향을 주게 된다. 이러한 영향을 최소화하기 위해 본 연구에서는 출력 단의 4 : 1 직렬 변환기의 두 복제본을 사용하여 클록 신호 위상 오류를 수정하는 QEC (Quadrature Error Corrector)를 제안하였다. 복제된 2개의 직렬 변환기의 출력을 비교하고 균등화하기 위해 펄스 수축 지연 라인이 사용되었다. 컨트롤러 PHY는 55nm CMOS 공정으로 제조되었다. PB-FFE는 1067Mbps에서 C/A 채널 타이밍 마진을 0.23UI에서 0.29UI로 증가시킨다. 읽기 트레이닝 후 읽기 타이밍 및 전압 마진은 2133Mbps에서 0.53UI 및 211mV이고, 쓰기 트레이닝 후 쓰기 마진은 0.72UI 및 230mV이다. QEC의 효과를 검증하기 위해 QEC를 포함한 프로토 타입 쿼터 레이트 송신기를 65nm CMOS의 다른 칩으로 제작하였다. QEC를 적용한 실험 결과, 송신기의 출력 위상 오류가 0.8ps의 잔류 오류로 감소하고, 출력 데이터 눈의 폭과 높이가 12.8Gbps의 데이터 속도에서 각각 84 %와 61 % 개선되었음을 보여준다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.1.1 HEAVY LOAD C/A CHANNEL 5 1.1.2 QUARTER-RATE ARCHITECTURE IN DQ TRANSMITTER 7 1.1.3 SUMMARY 8 1.2 THESIS ORGANIZATION 10 CHAPTER 2 ARCHITECTURE 11 2.1 MDS DIMM STRUCTURE 11 2.2 MDS CONTROLLER 15 2.3 MDS CONTROLLER PHY 17 2.3.1 INITIALIZATION SEQUENCE 20 2.3.2 LINK TRAINING FINITE-STATE MACHINE 23 2.3.3 POWER DOWN MODE 28 CHAPTER 3 PULSE-BASED FEED-FORWARD EQUALIZER 29 3.1 COMMAND/ADDRESS CHANNEL 29 3.2 COMMAND/ADDRESS TRANSMITTER 33 3.3 PULSE-BASED FEED-FORWARD EQUALIZER 35 CHAPTER 4 CIRCUIT IMPLEMENTATION 39 4.1 BUILDING BLOCKS 39 4.1.1 ALL-DIGITAL PHASE-LOCKED LOOP (ADPLL) 39 4.1.2 ALL-DIGITAL DELAY-LOCKED LOOP (ADDLL) 44 4.1.3 GLITCH-FREE DCDL CONTROL 47 4.1.4 DUTY-CYCLE CORRECTOR (DCC) 50 4.1.5 DQ/DQS TRANSMITTER 52 4.1.6 DQ/DQS RECEIVER 54 4.1.7 ZQ CALIBRATION 56 4.2 MODELING AND VERIFICATION OF LINK TRAINING 59 4.3 BUILT-IN SELF-TEST CIRCUITS 66 CHAPTER 5 QUADRATURE ERROR CORRECTOR USING REPLICA SERIALIZERS AND PULSE-SHRINKING DELAY LINES 69 5.1 PHASE CORRECTION USING REPLICA SERIALIZERS AND PULSE-SHRINKING UNITS 69 5.2 OVERALL QEC ARCHITECTURE AND ITS OPERATION 71 5.3 FINE DELAY UNIT IN THE PSDL 76 CHAPTER 6 EXPERIMENTAL RESULTS 78 6.1 CONTROLLER PHY 78 6.2 PROTOTYPE QEC 88 CHAPTER 7 CONCLUSION 94 BIBLIOGRAPHY 96Docto

Equalization Architectures for High Speed ADC-Based Serial I/O Receivers

The growth in worldwide network traffic due to the rise of cloud computing and wireless video consumption has required servers and routers to support increased serial I/O data rates over legacy channels with significant frequency-dependent attenuation. For these high-loss channel applications, ADC-based high-speed links are being considered due to their ability to enable powerful digital signal processing (DSP) algorithms for equalization and symbol detection. Relative to mixed-signal equalizers, digital implementations offer robustness to process, voltage and temperature (PVT) variations, are easier to reconfigure, and can leverage CMOS technology scaling in a straight-forward manner. Despite these advantages, ADC-based receivers are generally more complex and have higher power consumption relative to mixed-signal receivers. The ensuing digital equalization can also consume a significant amount of power which is comparable to the ADC contribution. Novel techniques to reduce complexity and improve power efficiency, both for the ADC and the subsequent digital equalization, are necessary. This dissertation presents efficient modeling and implementation approaches for ADC-based serial I/O receivers. A statistical modeling framework is developed, which is able to capture ADC related errors, including quantization noise, INL/DNL errors and time interleaving mismatch errors. A novel 10GS/s hybrid ADC-based receiver, which combines both embedded and digital equalization, is then presented. Leveraging a time-interleaved asynchronous successive approximation ADC architecture, a new structure for 3-tap embedded FFE inside the ADC with low power/area overhead is used. In addition, a dynamically-enabled digital 4-tap FFE + 3-tap DFE equalizer architecture is introduced, which uses reliable symbol detection to achieve remarkable savings in the digital equalization power. Measurement results over several FR4 channels verify the accuracy of the modeling approach and the effectiveness of the proposed receiver. The comparison of the fabricated prototype against state-of-the-art ADC-based receivers shows the ability of the proposed archi-tecture to compensate for the highest loss channel, while achieving the best power efficiency among other works

데이터 전송로 확장성과 루프 선형성을 향상시킨 다중채널 수신기들에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2013. 2. 정덕균.Two types of serial data communication receivers that adopt a multichannel architecture for a high aggregate I/O bandwidth are presented. Two techniques for collaboration and sharing among channels are proposed to enhance the loop-linearity and channel-expandability of multichannel receivers, respectively. The first proposed receiver employs a collaborative timing scheme recovery which relies on the sharing of all outputs of phase detectors (PDs) among channels to extract common information about the timing and multilevel signaling architecture of PAM-4. The shared timing information is processed by a common global loop filter and is used to update the phase of the voltage-controlled oscillator with better rejection of per-channel noise. In addition to collaborative timing recovery, a simple linearization technique for binary PDs is proposed. The technique realizes a high-rate oversampling PD while the hardware cost is equivalent to that of a conventional 2x-oversampling clock and data recovery. The first receiver exploiting the collaborative timing recovery architecture is designed using 45-nm CMOS technology. A single data lane occupies a 0.195-mm2 area and consumes a relatively low 17.9 mW at 6 Gb/s at 1.0V. Therefore, the power efficiency is 2.98 mW/Gb/s. The simulated jitter is about 0.034 UI RMS given an input jitter value of 0.03 UI RMS, while the relatively constant loop bandwidth with the PD linearization technique is about 7.3-MHz regardless of the data-stream noise. Unlike the first receiver, the second proposed multichannel receiver was designed to reduce the hardware complexity of each lane. The receiver employs shared calibration logic among channels and yet achieves superior channel expandability with slim data lanes. A shared global calibration control, which is used in a forwarded clock receiver based on a multiphase delay-locked loop, accomplishes skew calibration, equalizer adaptation, and the phase lock of all channels during a calibration period, resulting in reduced hardware overhead and less area required by each data lane. The second forwarded clock receiver is designed in 90-nm CMOS technology. It achieves error-free eye openings of more than 0.5 UI across 9− 28 inch Nelco 4000-6 microstrips at 4− 7 Gb/s and more than 0.42 UI at data rates of up to 9 Gb/s. The data lane occupies only 0.152 mm2 and consumes 69.8 mW, while the rest of the receiver occupies 0.297 mm2 and consumes 56 mW at a data rate of 7 Gb/s and a supply voltage of 1.35 V.1. Introduction 1 1.1 Motivations 1.2 Thesis Organization 2. Previous Receivers for Serial-Data Communications 2.1 Classification of the Links 2.2 Clocking architecture of transceivers 2.3 Components of receiver 2.3.1 Channel loss 2.3.2 Equalizer 2.3.3 Clock and data recovery circuit 2.3.3.1. Basic architecture 2.3.3.2. Phase detector 2.3.3.2.1. Linear phase detector 2.3.3.2.2. Binary phase detector 2.3.3.3. Frequency detector 2.3.3.4. Charge pump 2.3.3.5. Voltage controlled oscillator and delay-line 2.3.4 Loop dynamics of PLL 2.3.5 Loop dynamics of DLL 3. The Proposed PLL-Based Receiver with Loop Linearization Technique 3.1 Introduction 3.2 Motivation 3.3 Overview of binary phase detection 3.4 The proposed BBPD linearization technique 3.4.1 Architecture of the proposed PLL-based receiver 3.4.2 Linearization technique of binary phase detection 3.4.3 Rotational pattern of sampling phase offset 3.5 PD gain analysis and optimization 3.6 Loop Dynamics of the 2nd-order CDR 3.7 Verification with the time-accurate behavioral simulation 3.8 Summary 4. The Proposed DLL-Based Receiver with Forwarded-Clock 4.1 Introduction 4.2 Motivation 4.3 Design consideration 4.4 Architecture of the proposed forwarded-clock receiver 4.5 Circuit description 4.5.1 Analog multi-phase DLL 4.5.2 Dual-input interpolating deley cells 4.5.3 Dedicated half-rate data samplers 4.5.4 Cherry-Hooper continuous-time linear equalizer 4.5.5 Equalizer adaptation and phase-lock scheme 4.6 Measurement results 5. Conclusion 6. BibliographyDocto

Design of High-Speed SerDes Transceiver for Chip-to-Chip Communications in CMOS Process

With the continuous increase of on-chip computation capacities and exponential growth of data-intensive applications, the high-speed data transmission through serial links has become the backbone for modern communication systems. To satisfy the massive data-exchanging requirement, the data rate of such serial links has been updated from several Gb/s to tens of Gb/s. Currently, the commercial standards such as Ethernet 400GbE, InfiniBand high data rate (HDR), and common electrical interface (CEI)-56G has been developing towards 40+ Gb/s. As the core component within these links, the transceiver chipset plays a fundamental role in balancing the operation speed, power consumption, area occupation, and operation range. Meanwhile, the CMOS process has become the dominant technology in modern transceiver chip fabrications due to its large-scale digital integration capability and aggressive pricing advantage. This research aims to explore advanced techniques that are capable of exploiting the maximum operation speed of the CMOS process, and hence provides potential solutions for 40+ Gb/s CMOS transceiver designs. The major contributions are summarized as follows. A low jitter ring-oscillator-based injection-locked clock multiplier (RILCM) with a hybrid frequency tracking loop that consists of a traditional phase-locked loop (PLL), a timing-adjusted loop, and a loop selection state-machine is implemented in 65-nm C-MOS process. In the ring voltage-controlled oscillator, a full-swing pseudo-differential delay cell is proposed to lower the device noise to phase noise conversion. To obtain high operation speed and high detection accuracy, a compact timing-adjusted phase detector tightly combined with a well-matched charge pump is designed. Meanwhile, a lock-loss detection and lock recovery is devised to endow the RILCM with a similar lock-acquisition ability as conventional PLL, thus excluding the initial frequency set- I up aid and preventing the potential lock-loss risk. The experimental results show that the figure-of-merit of the designed RILCM reaches -247.3 dB, which is better than previous RILCMs and even comparable to the large-area LC-ILCMs. The transmitter (TX) and receiver (RX) chips are separately designed and fab- ricated in 65-nm CMOS process. The transmitter chip employs a quarter-rate multi-multiplexer (MUX)-based 4-tap feed-forward equalizer (FFE) to pre-distort the output. To increase the maximum operating speed, a bandwidth-enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. The receiver chip employs a two-stage continuous-time linear equalizer (CTLE) as the analog front-end and integrates an improved clock data recovery to extract the sampling clocks and retime the incoming data. To automatically balance the jitter tracking and jitter suppression, passive low-pass filters with adaptively-adjusted bandwidth are introduced into the data-sampling path. To optimize the linearity of the phase interpolation, a time-averaging-based compensating phase interpolator is proposed. For equalization, a combined TX-FFE and RX-CTLE is applied to compensate for the channel loss, where a low-cost edge-data correlation-based sign zero-forcing adaptation algorithm is proposed to automatically adjust the TX-FFE’s tap weights. Measurement results show that the fabricated transmitter/receiver chipset can deliver 40 Gb/s random data at a bit error rate of 16 dB loss at the half-baud frequency, while consuming a total power of 370 mW

Design Techniques for Energy Efficient Multi-GB/S Serial I/O Transceivers

Total I/O bandwidth demand is growing in high-performance systems due to the emergence of many-core microprocessors and in mobile devices to support the next generation of multi-media features. High-speed serial I/O energy efficiency must improve in order to enable continued scaling of these parallel computing platforms in applications ranging from data centers to smart mobile devices. The first work, a low-power forwarded-clock I/O transceiver architecture is presented that employs a high degree of output/input multiplexing, supply-voltage scaling with data rate, and low-voltage circuit techniques to enable low-power operation. The transmitter utilizes a 4:1 output multiplexing voltage-mode driver along with 4-phase clocking that is efficiently generated from a passive poly-phase filter. The output driver voltage swing is accurately controlled from 100-200 mV_(ppd) using a low-voltage pseudo-differential regulator that employs a partial negative-resistance load for improved low frequency gain. 1:8 input de-multiplexing is performed at the receiver equalizer output with 8 parallel input samplers clocked from an 8-phase injection-locked oscillator that provides more than 1UI de-skew range. Low-power high-speed serial I/O transmitters which include equalization to compensate for channel frequency dependent loss are required to meet the aggressive link energy efficiency targets of future systems. The second work presents a low power serial link transmitter design that utilizes an output stage which combines a voltage-mode driver, which offers low static-power dissipation, and current-mode equalization, which offers low complexity and dynamic-power dissipation. The utilization of current-mode equalization decouples the equalization settings and termination impedance, allowing for a significant reduction in pre-driver complexity relative to segmented voltage-mode drivers. Proper transmitter series termination is set with an impedance control loop which adjusts the on-resistance of the output transistors in the driver voltage-mode portion. Further reductions in dynamic power dissipation are achieved through scaling the serializer and local clock distribution supply with data rate. Finally, it presents that a scalable quarter-rate transmitter employs an analog-controlled impedance-modulated 2-tap voltage-mode equalizer and achieves fast power-state transitioning with a replica-biased regulator and ILO clock generation. Capacitively-driven 2 mm global clock distribution and automatic phase calibration allows for aggressive supply scaling

통계적 주파수 검출기 기반 기준 주파수를 사용하지 않는 클록 및 데이터 복원 회로의 설계 방법론

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this thesis, a design of a high-speed, power-efficient, wide-range clock and data recovery (CDR) without a reference clock is proposed. A frequency acquisition scheme using a stochastic frequency detector (SFD) based on the Alexander phase detector (PD) is utilized for the referenceless operation. Pat-tern histogram analysis is presented to analyze the frequency acquisition behavior of the SFD and verified by simulation. Based on the information obtained by pattern histogram analysis, SFD using autocovariance is proposed. With a direct-proportional path and a digital integral path, the proposed referenceless CDR achieves frequency lock at all measurable conditions, and the measured frequency acquisition time is within 7μs. The prototype chip has been fabricated in a 40-nm CMOS process and occupies an active area of 0.032 mm2. The proposed referenceless CDR achieves the BER of less than 10-12 at 32 Gb/s and exhibits an energy efficiency of 1.15 pJ/b at 32 Gb/s with a 1.0 V supply.본 논문은 기준 클럭이 없는 고속, 저전력, 광대역으로 동작하는 클럭 및 데이터 복원회로의 설계를 제안한다. 기준 클럭이 없는 동작을 위해서 알렉산더 위상 검출기에 기반한 통계적 주파수 검출기를 사용하는 주파수 획득 방식이 사용된다. 통계적 주파수 검출기의 주파수 추적 양상을 분석하기 위해 패턴 히스토그램 분석 방법론을 제시하였고 시뮬레이션을 통해 검증하였다. 패턴 히스토그램 분석을 통해 얻은 정보를 바탕으로 자기공분산을 이용한 통계적 주파수 검출기를 제안한다. 직접 비례 경로와 디지털 적분 경로를 통해 제안된 기준 클럭이 없는 클럭 및 데이터 복원회로는 모든 측정 가능한 조건에서 주파수 잠금을 달성하는 데 성공하였고, 모든 경우에서 측정된 주파수 추적 시간은 7μs 이내이다. 40-nm CMOS 공정을 이용하여 만들어진 칩은 0.032 mm2의 면적을 차지한다. 제안하는 클럭 및 데이터 복원회로는 32 Gb/s의 속도에서 비트에러율 10-12 이하로 동작하였고, 에너지 효율은 32Gb/s의 속도에서 1.0V 공급전압을 사용하여 1.15 pJ/b을 달성하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 13 CHAPTER 2 BACKGROUNDS 14 2.1 CLOCKING ARCHITECTURES IN SERIAL LINK INTERFACE 14 2.2 GENERAL CONSIDERATIONS FOR CLOCK AND DATA RECOVERY 24 2.2.1 OVERVIEW 24 2.2.2 JITTER 26 2.2.3 CDR JITTER CHARACTERISTICS 33 2.3 CDR ARCHITECTURES 39 2.3.1 PLL-BASED CDR – WITH EXTERNAL REFERENCE CLOCK 39 2.3.2 DLL/PI-BASED CDR 44 2.3.3 PLL-BASED CDR – WITHOUT EXTERNAL REFERENCE CLOCK 47 2.4 FREQUENCY ACQUISITION SCHEME 50 2.4.1 TYPICAL FREQUENCY DETECTORS 50 2.4.1.1 DIGITAL QUADRICORRELATOR FREQUENCY DETECTOR 50 2.4.1.2 ROTATIONAL FREQUENCY DETECTOR 54 2.4.2 PRIOR WORKS 56 CHAPTER 3 DESIGN OF THE REFERENCELESS CDR USING SFD 58 3.1 OVERVIEW 58 3.2 PROPOSED FREQUENCY DETECTOR 62 3.2.1 MOTIVATION 62 3.2.2 PATTERN HISTOGRAM ANALYSIS 68 3.2.3 INTRODUCTION OF AUTOCOVARIANCE TO STOCHASTIC FREQUENCY DETECTOR 75 3.3 CIRCUIT IMPLEMENTATION 83 3.3.1 IMPLEMENTATION OF THE PROPOSED REFERENCELESS CDR 83 3.3.2 CONTINUOUS-TIME LINEAR EQUALIZER (CTLE) 85 3.3.3 DIGITALLY-CONTROLLED OSCILLATOR (DCO) 87 3.4 MEASUREMENT RESULTS 89 CHAPTER 4 CONCLUSION 99 APPENDIX A DETAILED FREQUENCY ACQUISITION WAVEFORMS OF THE PROPOSED SFD 100 BIBLIOGRAPHY 108 초 록 122박

Design of energy efficient high speed I/O interfaces

Energy efficiency has become a key performance metric for wireline high speed I/O interfaces. Consequently, design of low power I/O interfaces has garnered large interest that has mostly been focused on active power reduction techniques at peak data rate. In practice, most systems exhibit a wide range of data transfer patterns. As a result, low energy per bit operation at peak data rate does not necessarily translate to overall low energy operation. Therefore, I/O interfaces that can scale their power consumption with data rate requirement are desirable. Rapid on-off I/O interfaces have a potential to scale power with data rate requirements without severely affecting either latency or the throughput of the I/O interface. In this work, we explore circuit techniques for designing rapid on-off high speed wireline I/O interfaces and digital fractional-N PLLs. A burst-mode transmitter suitable for rapid on-off I/O interfaces is presented that achieves 6 ns turn-on time by utilizing a fast frequency settling ring oscillator in digital multiplying delay-locked loop and a rapid on-off biasing scheme for current mode output driver. Fabricated in 90 nm CMOS process, the prototype achieves 2.29 mW/Gb/s energy efficiency at peak data rate of 8 Gb/s. A 125X (8 Gb/s to 64 Mb/s) change in effective data rate results in 67X (18.29 mW to 0.27 mW) change in transmitter power consumption corresponding to only 2X (2.29 mW/Gb/s to 4.24 mW/Gb/s) degradation in energy efficiency for 32-byte long data bursts. We also present an analytical bit error rate (BER) computation technique for this transmitter under rapid on-off operation, which uses MDLL settling measurement data in conjunction with always-on transmitter measurements. This technique indicates that the BER bathtub width for 10^(−12) BER is 0.65 UI and 0.72 UI during rapid on-off operation and always-on operation, respectively. Next, a pulse response estimation-based technique is proposed enabling burst-mode operation for baud-rate sampling receivers that operate over high loss channels. Such receivers typically employ discrete time equalization to combat inter-symbol interference. Implementation details are provided for a receiver chip, fabricated in 65nm CMOS technology, that demonstrates efficacy of the proposed technique. A low complexity pulse response estimation technique is also presented for low power receivers that do not employ discrete time equalizers. We also present techniques for implementation of highly digital fractional-N PLL employing a phase interpolator based fractional divider to improve the quantization noise shaping properties of a 1-bit ∆Σ frequency-to-digital converter. Fabricated in 65nm CMOS process, the prototype calibration-free fractional-N Type-II PLL employs the proposed frequency-to-digital converter in place of a high resolution time-to-digital converter and achieves 848 fs rms integrated jitter (1 kHz-30 MHz) and -101 dBc/Hz in-band phase noise while generating 5.054 GHz output from 31.25 MHz input

Hybrid NRZ/Multi-Tone Signaling for High-Speed Low-Power Wireline Transceivers

Over the past few decades, incessant growth of Internet networking traffic and High-Performance Computing (HPC) has led to a tremendous demand for data bandwidth. Digital communication technologies combined with advanced integrated circuit scaling trends have enabled the semiconductor and microelectronic industry to dramatically scale the bandwidth of high-loss interfaces such as Ethernet, backplane, and Digital Subscriber Line (DSL). The key to achieving higher bandwidth is to employ equalization technique to compensate the channel impairments such as Inter-Symbol Interference (ISI), crosstalk, and environmental noise. Therefore, todayâs advanced input/outputs (I/Os) has been equipped with sophisticated equalization techniques to push beyond the uncompensated bandwidth of the system. To this end, process scaling has continually increased the data processing capability and improved the I/O performance over the last 15 years. However, since the channel bandwidth has not scaled with the same pace, the required signal processing and equalization circuitry becomes more and more complicated. Thereby, the energy efficiency improvements are largely offset by the energy needed to compensate channel impairments. In this design paradigm, re-thinking about the design strategies in order to not only satisfy the bandwidth performance, but also to improve power-performance becomes an important necessity. It is well known in communication theory that coding and signaling schemes have the potential to provide superior performance over band-limited channels. However, the choice of the optimum data communication algorithm should be considered by accounting for the circuit level power-performance trade-offs. In this thesis we have investigated the application of new algorithm and signaling schemes in wireline communications, especially for communication between microprocessors, memories, and peripherals. A new hybrid NRZ/Multi-Tone (NRZ/MT) signaling method has been developed during the course of this research. The system-level and circuit-level analysis, design, and implementation of the proposed signaling method has been performed in the frame of this work, and the silicon measurement results have proved the efficiency and the robustness of the proposed signaling methodology for wireline interfaces. In the first part of this work, a 7.5 Gb/s hybrid NRZ/MT transceiver (TRX) for multi-drop bus (MDB) memory interfaces is designed and fabricated in 40 nm CMOS technology. Reducing the complexity of the equalization circuitry on the receiver (RX) side, the proposed architecture achieves 1 pJ/bit link efficiency for a MDB channel bearing 45 dB loss at 2.5 GHz. The measurement results of the first prototype confirm that NRZ/MT serial data TRX can offer an energy-efficient solution for MDB memory interfaces. Motivated by the satisfying results of the first prototype, in the second phase of this research we have exploited the properties of multi-tone signaling, especially orthogonality among different sub-bands, to reduce the effect of crosstalk in high-dense wireline interconnects. A four-channel transceiver has been implemented in a standard CMOS 40 nm technology in order to demonstrate the performance of NRZ/MT signaling in presence of high channel loss and strong crosstalk noise. The proposed system achieves 1 pJ/bit power efficiency, while communicating over a MDB memory channel at 36 Gb/s aggregate data rate

PHY Link Design and Optimization For High-Speed Low-Power Communication Systems

The ever-growing demands for high-bandwidth data transfer have been pushing towards advancing research efforts in the field of high-performing communication systems. Studies on the performance of single chip, e.g. faster multi-core processors and higher system memory capacity, have been explored. To further enhance the system performance, researches have been focused on the improvement of data-transfer bandwidth for chip-to-chip communication in the high-speed serial link. Many solutions have been addressed to overcome the bottleneck caused by the non-idealties such as bandwidth-limited electrical channel that connects two link devices and varieties of undesired noise in the communication systems. Nevertheless, with these solutions data have run into limitations of the timing margins for high-speed interfaces running at multiple gigabits per second data rates on low-cost Printed Circuit Board (PCB) material with constrained power budget. Therefore, the challenge in designing a physical layer (PHY) link for high-speed communication systems turns out to be power-efficient, reliable and cost-effective. In this context, this dissertation is intended to focus on architectural design, system-level and circuit-level verification of a PHY link as well as system performance optimization in respective of power, reliability and adaptability in high-speed communication systems. The PHY is mainly composed of clock data recovery (CDR), equalizers (EQs) and high- speed I/O drivers. Symmetrical structure of the PHY link is usually duplicated in both link devices for bidirectional data transmission. By introducing training mechanisms into high-speed communication systems, the timing in one link device is adaptively aligned to the timing condition specified in the other link device despite of different skews or induced jitter resulting from process, voltage and temperature (PVT) variations in the individual link. With reliable timing relationships among the interface signals provided, the total system bandwidth is dramatically improved. On the other hand, interface training offers high flexibility for reuse without further investigation on high demanding components involved in high costs. In the training mode, a CDR module is essential for reconstructing the transmitted bitstream to achieve the best data eye and to detect the edges of data stream in asynchronous systems or source-synchronous systems. Generally, the CDR works as a feedback control system that aligns its output clock to the center of the received data. In systems that contain multiple data links, the overall CDR power consumption increases linearly with the increase in number of links as one CDR is required for each link. Therefore, a power-efficient CDR plays a significant role in such systems with parallel links. Furthermore, a high performance CDR requires low jitter generation in spite of high input jitter. To minimize the trade-off between power consumption and CDR jitter, a novel CDR architecture is proposed by utilizing the proportional-integral (PI) controller and three times sampling scheme. Meanwhile, signal integrity (SI) becomes critical as the data rate exceeds several gigabits per second. Distorted data due to the non-idealties in systems are likely to reduce the signal quality aggressively and result in intolerable transmission errors in worst case scenarios, thus affect the system effective bandwidth. Hence, additional trainings such as transmitter (Tx) and receiver (Rx) EQ trainings for SI purpose are inserted into the interface training. Besides, a simplified system architecture with unsymmetrical placement of adaptive Rx and Tx EQs in a single link device is proposed and analyzed by using different coefficient adaptation algorithms. This architecture enables to reduce a large number of EQs through the training, especially in case of parallel links. Meanwhile, considerable power and chip area are saved. Finally, high-speed I/O driver against PVT variations is discussed. Critical issues such as overshoot and undershoot interfering with the data are primarily accompanied by impedance mismatch between the I/O driver and its transmitting channel. By applying PVT compensation technique I/O driver impedances can be effectively calibrated close to the target value. Different digital impedance calibration algorithms against PVT variations are implemented and compared for achieving fast calibration and low power requirements