Phase Noise in CMOS Phase-Locked Loop Circuits

Phase-locked loops (PLLs) have been widely used in mixed-signal integrated circuits. With the continuously increasing demand of market for high speed, low noise devices, PLLs are playing a more important role in communications. In this dissertation, phase noise and jitter performances are investigated in different types of PLL designs. Hot carrier and negative bias temperature instability effects are analyzed from simulations and experiments. Phase noise of a CMOS phase-locked loop as a frequency synthesizer circuit is modeled from the superposition of noises from its building blocks: voltage-controlled oscillator, frequency divider, phase-frequency detector, loop filter and auxiliary input reference clock. A linear time invariant model with additive noise sources in frequency domain is presented to analyze the phase noise. The modeled phase noise results are compared with the corresponding experimentally measured results on phase-locked loop chips fabricated in 0.5 m n-well CMOS process. With the scaling of CMOS technology and the increase of electrical field, MOS transistors have become very sensitive to hot carrier effect (HCE) and negative bias temperature instability (NBTI). These two reliability issues pose challenges to designers for designing of chips in deep submicron CMOS technologies. A new strategy of switchable CMOS phase-locked loop frequency synthesizer is proposed to increase its tuning range. The switchable PLL which integrates two phase-locked loops with different tuning frequencies are designed and fabricated in 0.5 µm CMOS process to analyze the effects under HCE and NBTI. A 3V 1.2 GHz programmable phase-locked loop frequency synthesizer is designed in 0.5 μm CMOS technology. The frequency synthesizer is implemented using LC voltage-controlled oscillator (VCO) and a low power dual-modulus prescaler. The LC VCO working range is from 900MHz to 1.4GHz. Current mode logic (CML) is used in designing high speed D flip-flop in the dual-modulus prescaler circuits for low power consumption. The power consumption of the PLL chip is under 30mW. Fully differential LC VCO is used to provide high oscillation frequency. A new design of LC VCO using carbon nanotube (CNT) wire inductor has been proposed. The PLL design using CNT-LC VCO shows significant improvement in phase noise due to high-Q LC circuit

Integrated radio frequency synthetizers for wireless applications

This thesis consists of six publications and an overview of the research topic, which is also a summary of the work. The research described in this thesis concentrates on the design of phase-locked loop radio frequency synthesizers for wireless applications. In particular, the focus is on the implementation of the prescaler, the phase detector, and the chargepump. This work reviews the requirements set for the frequency synthesizer by the wireless standards, and how these requirements are derived from the system specifications. These requirements apply to both integer-N and fractional-N synthesizers. The work also introduces the special considerations related to the design of fractional-N phase-locked loops. Finally, implementation alternatives for the different building blocks of the synthesizer are reviewed. The presented work introduces new topologies for the phase detector and the chargepump, and improved topologies for high speed CMOS prescalers. The experimental results show that the presented topologies can be successfully used in both integer-N and fractional-N synthesizers with state-of-the-art performance. The last part of this work discusses the additional considerations that surface when the synthesizer is integrated into a larger system chip. It is shown experimentally that the synthesizer can be successfully integrated into a complex transceiver IC without sacrificing the performance of the synthesizer or the transceiver.reviewe

Design and Analysis of a Wide Loop-Bandwidth RF Synthesizer Using Ring oscillator For DECT Receiver

Wireless communication devices including cordless phones and modern digital cellular systems (DCSs) use portable transceiver systems. The frequency synthesis of this type of transceiver system is done using a phase-locked loop oscillator. Traditional on-chip implementation of a complete phase-locked loop using a ring type voltage controlled oscillator contributes higher noise at the output. An alternative architecture, phase-locked loop (PLL) with wide loop-bandwidth, is proposed in this research to suppress the noise from the traditional ring oscillator. The proposed PLL is amendable to on-chip integration as well as commercially suitable for a Digital Enhancement Cordless Telephone (DECT) system which needs flexible noise margin. In this research, a 1.5552 GHz PLL-based frequency synthesizer is designed with a noisy ring oscillator. The wide loop-bandwidth approach is applied in designing the PLL to suppress the VCO noise. In this type of frequency synthesizer, the frequency divider is operated at higher frequencies with less noise and care is taken to design the delay flip-flops and logic gates that can be operated at higher frequencies. Current-mode control can be employed in designing the logic gates and the delay flip-flop to enhance the speed performance of the divider. An alternate approach in designing a high-speed divider using a current-mode control approach is also presented

A Programmable Frequency Divider Having a Wide Division Ratio Range, and Close-to-50% Output Duty-Cycle

In Radio Frequency (RF) integrated circuit design field, programmable dividers are getting more and more attentions in recent years. A programmable frequency divider can divide an input frequency by programmable ratios [1]. It is a key component of a frequency synthesizer. It also can be used to generate variable clock-signals for: switched-capacitor filters (SCFs), digital systems with different power-states, as well as multiple clock-signals on the same system-on-a-chip (SOC). These circuits need high performance programmable frequency dividers, operating at high frequencies and having wide division ratio ranges, with binary division ratio controls and 50% output duty-cycle. Different types of programmable frequency dividers are reviewed and compared. A programmable frequency divider with a wide division ratio range of (8 ~ 524287) has been reported [2]. Because the output duty-cycle of this reported divider is far from 50%, the circuit in [2] has very limited applications. The proposed design solves this problem, without compromising other advantages of the design in [2]. The proposed design is fabricated in a 0.18-μm RF CMOS process. Test results show that the output duty-cycle is 50% when the division ratio is an even number. The duty-cycle is 44.4% when the division ratio is 9. The output duty-cycle becomes closer to 50% when the division ratio is an increasing odd number. For each division ratio, the output duty-cycle remains constant, with different input frequencies from GHz down to kHz ranges, with different temperatures and power supply voltages. This thesis provides an explanation of the design details and test results. A Phase Locked-Loop (PLL) based frequency synthesizer can generate different output frequencies. A programmable frequency divider is an important component of this type of PLL. Since bandwidth is expensive, it is preferred to reduce the frequency channel distance of a frequency synthesizer. Using a fractional programmable divider, the frequency channel distance of a PLL can be reduced, without reducing the reference frequency or increasing the settling time of the PLL. A frequency synthesizer with a programmable fractional divider is designed and fabricated. A brief description of the PLL design and test results are presented in this dissertation

A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

Design and implementation of frequency synthesizers for 3-10 ghz mulitband ofdm uwb communication

The allocation of frequency spectrum by the FCC for Ultra Wideband (UWB) communications in the 3.1-10.6 GHz has paved the path for very high data rate Gb/s wireless communications. Frequency synthesis in these communication systems involves great challenges such as high frequency and wideband operation in addition to stringent requirements on frequency hopping time and coexistence with other wireless standards. This research proposes frequency generation schemes for such radio systems and their integrated implementations in silicon based technologies. Special emphasis is placed on efficient frequency planning and other system level considerations for building compact and practical systems for carrier frequency generation in an integrated UWB radio. This work proposes a frequency band plan for multiband OFDM based UWB radios in the 3.1-10.6 GHz range. Based on this frequency plan, two 11-band frequency synthesizers are designed, implemented and tested making them one of the first frequency synthesizers for UWB covering 78% of the licensed spectrum. The circuits are implemented in 0.25µm SiGe BiCMOS and the architectures are based on a single VCO at a fixed frequency followed by an array of dividers, multiplexers and single sideband (SSB) mixers to generate the 11 required bands in quadrature with fast hopping in much less than 9.5 ns. One of the synthesizers is integrated and tested as part of a 3-10 GHz packaged receiver. It draws 80 mA current from a 2.5 V supply and occupies an area of 2.25 mm2. Finally, an architecture for a UWB synthesizer is proposed that is based on a single multiband quadrature VCO, a programmable integer divider with 50% duty cycle and a single sideband mixer. A frequency band plan is proposed that greatly relaxes the tuning range requirement of the multiband VCO and leads to a very digitally intensive architecture for wideband frequency synthesis suitable for implementation in deep submicron CMOS processes. A design in 130nm CMOS occupies less than 1 mm2 while consuming 90 mW. This architecture provides an efficient solution in terms of area and power consumption with very low complexity

Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers

There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular. Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process. CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers. A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band. The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided

A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS

© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΔ fractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe

Architectures and Circuits Leveraging Injection-Locked Oscillators for Ultra-Low Voltage Clock Synthesis and Reference-less Receivers for Dense Chip-to-Chip Communications

High performance computing is critical for the needs of scientific discovery and economic competitiveness. An extreme-scale computing system at 1000x the performance of today’s petaflop machines will exhibit massive parallelism on multiple vertical fronts, from thousands of computational units on a single processor to thousands of processors in a single data center. To facilitate such a massively-parallel extreme-scale computing, a key challenge is power. The challenge is not power associated with base computation but rather the problem of transporting data from one chip to another at high enough rates. This thesis presents architectures and techniques to achieve low power and area footprint while achieving high data rates in a dense very-short reach (VSR) chip-to-chip (C2C) communication network. High-speed serial communication operating at ultra-low supplies improves the energy-efficiency and lowers the power envelop of a system doing an exaflop of loops. One focus area of this thesis is clock synthesis for such energy-efficient interconnect applications operating at high speeds and ultra-low supplies. A sub-integer clockfrequency synthesizer is presented that incorporates a multi-phase injection-locked ring-oscillator-based prescaler for operation at an ultra-low supply voltage of 0.5V, phase-switching based programmable division for sub-integer clock-frequency synthesis, and automatic calibration to ensure injection lock. A record speed of 9GHz has been demonstrated at 0.5V in 45nm SOI CMOS. It consumes 3.5mW of power at 9.12GHz and 0.052 of area, while showing an output phase noise of -100dBc/Hz at 1MHz offset and RMS jitter of 325fs; it achieves a net of -186.5 in a 45-nm SOI CMOS process. This thesis also describes a receiver with a reference-less clocking architecture for high-density VSR-C2C links. This architecture simplifies clock-tree planning in dense extreme-scaling computing environments and has high-bandwidth CDR to enable SSC for suppressing EMI and to mitigate TX jitter requirements. It features clock-less DFE and a high-bandwidth CDR based on master-slave ILOs for phase generation/rotation. The RX is implemented in 14nm CMOS and characterized at 19Gb/s. It is 1.5x faster that previous reference-less embedded-oscillator based designs with greater than 100MHz jitter tolerance bandwidth and recovers error-free data over VSR-C2C channels. It achieves a power-efficiency of 2.9pJ/b while recovering error-free data (BER 200MHz and the INL of the ILO-based phase-rotator (32- Steps/UI) is <1-LSB. Lastly, this thesis develops a time-domain delay-based modeling of injection locking to describe injection-locking phenomena in nonharmonic oscillators. The model is used to predict the locking bandwidth, and the locking dynamics of the locked oscillator. The model predictions are verified against simulations and measurements of a four-stage differential ring oscillator. The model is further used to predict the injection-locking behavior of a single-ended CMOS inverter based ring oscillator, the lock range of a multi-phase injection-locked ring-oscillator-based prescaler, as well as the dynamics of tracking injection phase perturbations in injection-locked masterslave oscillators; demonstrating its versatility in application to any nonharmonic oscillator

Transceiver architectures and sub-mW fast frequency-hopping synthesizers for ultra-low power WSNs

Wireless sensor networks (WSN) have the potential to become the third wireless revolution after wireless voice networks in the 80s and wireless data networks in the late 90s. This revolution will finally connect together the physical world of the human and the virtual world of the electronic devices. Though in the recent years large progress in power consumption reduction has been made in the wireless arena in order to increase the battery life, this is still not enough to achieve a wide adoption of this technology. Indeed, while nowadays consumers are used to charge batteries in laptops, mobile phones and other high-tech products, this operation becomes infeasible when scaled up to large industrial, enterprise or home networks composed of thousands of wireless nodes. Wireless sensor networks come as a new way to connect electronic equipments reducing, in this way, the costs associated with the installation and maintenance of large wired networks. To accomplish this task, it is necessary to reduce the energy consumption of the wireless node to a point where energy harvesting becomes feasible and the node energy autonomy exceeds the life time of the wireless node itself. This thesis focuses on the radio design, which is the backbone of any wireless node. A common approach to radio design for WSNs is to start from a very simple radio (like an RFID) adding more functionalities up to the point in which the power budget is reached. In this way, the robustness of the wireless link is traded off for power reducing the range of applications that can draw benefit form a WSN. In this thesis, we propose a novel approach to the radio design for WSNs. We started from a proven architecture like Bluetooth, and progressively we removed all the functionalities that are not required for WSNs. The robustness of the wireless link is guaranteed by using a fast frequency hopping spread spectrum technique while the power budget is achieved by optimizing the radio architecture and the frequency hopping synthesizer Two different radio architectures and a novel fast frequency hopping synthesizer are proposed that cover the large space of applications for WSNs. The two architectures make use of the peculiarities of each scenario and, together with a novel fast frequency hopping synthesizer, proved that spread spectrum techniques can be used also in severely power constrained scenarios like WSNs. This solution opens a new window toward a radio design, which ultimately trades off flexibility, rather than robustness, for power consumption. In this way, we broadened the range of applications for WSNs to areas in which security and reliability of the communication link are mandatory