15 research outputs found
Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications
As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well
Design of Power Management Integrated Circuits and High-Performance ADCs
A battery-powered system has widely expanded its applications to implantable medical devices
(IMDs) and portable electronic devices. Since portable devices or IMDs operate in the
energy-constrained environment, their low-power operations in combination with efficiently sourcing
energy to them are key problems to extend device life. This research proposes novel circuit
techniques for two essential functions of a power receiving unit (PRU) in the energy-constrained
environment, which are power management and signal processing.
The first part of this dissertation discusses power management integrated circuits for a PRU.
From a power management perspective, the most critical two circuit blocks are a front-end rectifier
and a battery charger. The front-end CMOS active rectifier converts transmitted AC power into
DC power. High power conversion efficiency (PCE) is required to reduce power loss during the
power transfer, and high voltage conversion ratio (VCR) is required for the rectifier to enable low-voltage
operations. The proposed 13.56-MHz CMOS active rectifier presents low-power circuit
techniques for comparators and controllers to reduce increasing power loss of an active diode with
offset/delay calibration. It is implemented with 5-V devices of a 0.35 Āµm CMOS process to support
high voltage. A peak PCE of 89.0%, a peak VCR of 90.1%, and a maximum output power of 126.7
mW are measured for 200Ī© loading.
The linear battery charger stores the converted DC power into a battery. Since even small
power saving can be enough to run the low-power PRU, a battery charger with low IvQ is desirable.
The presented battery charger is based on a single amplifier for regulation and the charging
phase transition from the constant-current (CC) phase to the constant-voltage (CV) phase. The
proposed unified amplifier is based on stacked differential pairs which share the bias current. Its
current-steering property removes multiple amplifiers for regulation and the CC-CV transition, and
achieves high unity-gain loop bandwidth for fast regulation. The charger with the maximum charging
current of 25 mA is implemented in 0.35 Āµm CMOS. A peak charger efficiency of 94% and
average charger efficiency of 88% are achieved with an 80-mAh Li-ion polymer battery.
The second part of this dissertation focuses on analog-to-digital converters (ADCs). From a
signal processing perspective, an ADC is one of the most important circuit blocks in the PRU.
Hence, an energy-efficient ADC is essential in the energy-constrained environment. A pipelined successive
approximation register (SAR) ADC has good energy efficiency in a design space of
moderate-to-high speeds and resolutions. Process-Voltage-Temperature variations of a dynamic
amplifier in the pipelined-SAR ADC is a key design issue. This research presents two dynamic
amplifier architectures for temperature compensation. One is based on a voltage-to-time converter
(VTC) and a time-to-voltage converter (TVC), and the other is based on a temperature-dependent
common-mode detector. The former amplifier is adopted in a 13-bit 10-50 MS/s subranging
pipelined-SAR ADC fabricated in 0.13-Āµm CMOS. The ADC can operate under the power supply
voltage of 0.8-1.2 V. Figure-of-Merits (FoMs) of 4-11.3 fJ/conversion-step are achieved. The latter
amplifier is also implemented in 0.13-Āµm CMOS, consuming 0.11 mW at 50 MS/s. Its measured
gain variation is 2.1% across the temperature range of -20Ā°C to 85 Ā°C
Recommended from our members
Design Techniques for High-Performance SAR A/D Converters
The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs.
ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ā¼GS/s sampling rates at reasonable power consumption.
Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADCās SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s.
The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew
calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ā¼GS/s with 10-bit resolution and a power consumption as low as ā¼10mW; specifications that satisfy the requirements of 5G technology
Recommended from our members
Design techniques for low-power SAR ADCs in nano-scale CMOS technologies
This thesis presents low power design techniques for successive approximation register (SAR) analog-to-digital converters (ADCs) in nano-scale CMOS technologies. Low power SAR ADCs face two major challenges especially at high resolutions: (1) increased comparator power to suppress the noise, and (2) increased DAC switching energy due to the large DAC size. To improve the comparatorās power efficiency, a statistical estimation based comparator noise reduction technique is presented. It allows a low power and noisy comparator to achieve high signal-to-noise ratio (SNR) by estimating the conversion residue. A first prototype ADC in 65nm CMOS has been developed to validate the proposed noise reduction technique. It achieves 4.5 fJ/conv-step Walden figure of merit and 64.5 dB signal-to-noise and distortion ratio (SNDR). In addition, a bidirectional single-side switching technique is developed to reduce the DAC switching power. It can reduce the DAC switching power and the total number of unit capacitors by 86% and 75%, respectively. A second prototype ADC with the proposed switching technique is designed and fabricated in 180nm CMOS technology. It achieves an SNDR of 63.4 dB and consumes only 24 Wat 1MS/s, leading to aWalden figure of merit of 19.9 fJ/conv-step. This thesis also presents an improved loop-unrolled SAR ADC, which works at high frequency with reduced SAR logic power and delay. It employs the bidirectional single-side switching technique to reduce the comparator common-mode voltage variation. In addition, it uses a Vcm-adaptive offset calibration technique which can accurately calibrate comparatorās offset at its operating Vcm. A prototype ADC designed in 40nm CMOS achieves 35 dB at 700 MS/s sampling rate and consumes only 0.95 mW, leading to a Walden figure of merit of 30 fJ/conv-step.Electrical and Computer Engineerin
Built-in self-test and self-calibration for analog and mixed signal circuits
Analog-to-digital converters (ADC) are one of the most important components in modern electronic systems. In the mission-critical applications such as automotive, the reliability of the ADC is critical as the ADC impacts the system level performance. Due to the aging effect and environmental changes, the performance of the ADC may degrade and even fail to meet the accuracy requirement over time. Built-in self-test (BIST) and self-calibration are becoming the ultimate solution to achieve lifetime reliability. This dissertation introduces two ADC testing algorithms and two ADC built-in self-test circuit implementations to test the ADC integral nonlinearity (INL) and differential nonlinearity (DNL) on-chip.
In the first testing algorithm, the ultrafast stimulus error removal and segmented model identification of linearity errors (USER-SMILE) is developed for ADC built-in self-test, which eliminates the need for precision stimulus and reduces the overall test time. In this algorithm, the ADC is tested twice with a nonlinear ramp, instead of using a linear ramp signal. Therefore, the stimulus can be easily generated on-chip in a low-cost way. For the two ramps, there is a constant voltage shift in between. As the input stimulus linearity is completely relaxed, there is no requirement on the waveform of the input stimulus as long as it covers the ADC input range. In the meantime, the high-resolution ADC linearity is modeled with segmented parameters, which reduces the number of samples required for achieving high-precision test, thus saving the test time. As a result, the USER-SMILE algorithm is able to use less than 1 sample/code nonlinear stimulus to test high resolution ADCs with less than 0.5 least significant bit (LSB) INL estimation error, achieving more than 10-time test time reduction. This algorithm is validated with both board-level implementation and on-chip silicon implementation.
The second testing algorithm is proposed to test the INL/DNL for multi-bit-per-stages pipelined ADCs with reduced test time and better test coverage. Due to the redundancy characteristics of multi-bit-per-stages pipelined ADC, the conventional histogram test cannot estimate and calibrate the static linearity accurately. The proposed method models the pipelined ADC nonlinearity as segmented parameters with inter-stage gain errors using the raw codes instead of the final output codes. During the test phase, a pure sine wave is sent to the ADC as the input and the model parameters are estimated from the output data with the system identification method. The modeled errors are then removed from the digital output codes during the calibration phase. A high-speed 12-bit pipelined ADC is tested and calibrated with the proposed method. With only 4000 samples, the 12-bit ADC is accurately tested and calibrated to achieve less than 1 LSB INL. The ADC effective number of bits (ENOB) is improved from 9.7 bits to 10.84 bits and the spurious-free dynamic range (SFDR) is improved by more than 20dB after calibration.
In the first circuit implementation, a low-cost on-chip built-in self-test solution is developed using an R2R digital-to-analog converter (DAC) structure as the signal generator and the voltage shift generator for ADC linearity test. The proposed DAC is a subradix-2 R2R DAC with a constant voltage shift generation capability. The subradix-2 architecture avoids positive voltage gaps caused by mismatches, which relaxes the DAC matching requirements and reduces the design area. The R2R DAC based BIST circuit is fabricated in TSMC 40nm technology with a small area of 0.02mm^2. Measurement results show that the BIST circuit is capable of testing a 15-bit ADC INL accurately with less than 0.5 LSB INL estimation error.
In the second circuit implementation, a complete SAR ADC built-in self-test solution using the USER-SMILE is developed and implemented in a 28nm automotive microcontroller. A low-cost 12-bit resistive DAC with less than 12-bit linearity is used as the signal generator to test and calibrate a SAR ADC with a target linearity of 12 bits. The voltage shift generation is created inside the ADC with capacitor switching. The entire algorithm processing unit for USER-SMILE algorithm is also implemented on chip. The final testing results are saved in the memory for further digital calibration. Both the total harmonic distortion (THD) and the SFDR are improved by 20dB after calibration, achieving -84.5dB and 86.5dB respectively. More than 700 parts are tested to verify the robustness of the BIST solution
?????? ?????? ???????????? ?????? ???????????? ??????????????? ?????????????????? ??? ???????????????
Department of Electrical EngineeringA Sensor system is advanced along sensor technologies are developed. The performance improvement of sensor system can be expected by using the internet of things (IoT) communication technology and artificial neural network (ANN) for data processing and computation. Sensors or systems exchanged the data through this wireless connectivity, and various systems and applications are possible to implement by utilizing the advanced technologies. And the collected data is computed using by the ANN and the efficiency of system can be also improved.
Gas monitoring system is widely need from the daily life to hazardous workplace. Harmful gas can cause a respiratory disease and some gas include cancer-causing component. Even though it may cause dangerous situation due to explosion. There are various kinds of hazardous gas and its characteristics that effect on human body are different each gas. The optimal design of gas monitoring system is necessary due to each gas has different criteria such as the permissible concentration and exposure time. Therefore, in this thesis, conventional sensor system configuration, operation, and limitation are described and gas monitoring system with wireless connectivity and neural network is proposed to improve the overall efficiency.
As I already mentioned above, dangerous concentration and permissible exposure time are different depending on gas types. During the gas monitoring, gas concentration is lower than a permissible level in most of case. Thus, the gas monitoring is enough with low resolution for saving the power consumption in this situation. When detecting the gas, the high-resolution is required for the accurate concentration detecting. If the gas type is varied in the above situation, the amount of calculation increases exponentially. Therefore, in the conventional systems, target specifications are decided by the highest requirement in the whole situation, and it occurs increasing the cost and complexity of readout integrated circuit (ROIC) and system. In order to optimize the specification, the ANN and adaptive ROIC are utilized to compute the complex situation and huge data processing.
Thus, gas monitoring system with learning-based algorithm is proposed to improve its efficiency. In order to optimize the operation depending on situation, dual-mode ROIC that monitoring mode and precision mode is implemented. If the present gas concentration is decided to safe, monitoring mode is operated with minimal detecting accuracy for saving the power consumption. The precision mode is switched when the high-resolution or hazardous situation are detected. The additional calibration circuits are necessary for the high-resolution implementation, and it has more power consumption and design complexity. A high-resolution Analog-to-digital converter (ADC) is kind of challenges to design with efficiency way. Therefore, in order to reduce the effective resolution of ADC and power consumption, zooming correlated double sampling (CDS) circuit and prediction successive approximation register (SAR) ADC are proposed for performance optimization into precision mode.
A Microelectromechanical systems (MEMS) based gas sensor has high-integration and high sensitivity, but the calibration is needed to improve its low selectivity. Conventionally, principle component analysis (PCA) is used to classify the gas types, but this method has lower accuracy in some case and hard to verify in real-time. Alternatively, ANN is powerful algorithm to accurate sensing through collecting the data and training procedure and it can be verified the gas type and concentration in real-time. ROIC was fabricated in complementary metal-oxide-semiconductor (CMOS) 180-nm process and then the efficiency of the system with adaptive ROIC and ANN algorithm was experimentally verified into gas monitoring system prototype. Also, Bluetooth supports wireless connectivity to PC and mobile and pattern recognition and prediction code for SAR ADC is performed in MATLAB. Real-time gas information is monitored by Android-based application in smartphone. The dual-mode operation, optimization of performance and prediction code are adjusted with microcontroller unit (MCU). Monitoring mode is improved by x2.6 of figure-of-merits (FoM) that compared with previous resistive interface.clos
Digitally Assisted ADCS.
This work involves the development of digital calibration techniques for Analogto-
Digital Converters. According to the 2001 International Technology Roadmap for
Semiconductors, improved ADC technology is a key factor in the development of present
and future applications.
The switched-capacitor (SC) pipeline technique is the most popular method of
implementing moderate resolution ADCs. However the advantages of CMOS, which
originally made SC circuits feasible, are being eroding by process scaling. Good switches
and opamps are becoming increasingly difficult to design and the growing gate leakage
of deep submicron MOSFETs is causing difficulty. Traditional ADC schemes do not
work well with supply voltages of 1.8V and below. Furthermore, the performance required by present and future wireless and IT applications will not be met by the present
day ADC circuits techniques.
Bearing in mind the challenges associated with deep sub-micron analog circuitry
a new calibration technique for folding ADCs has been developed. Since digital circuitry
scales well, this calibration relies heavily on digital techniques. Hence it reduces the
amount of analog design involved. As this folding ADC is dominated, in terms of both
functionality and power, by digital circuitry, the performance of folding will improve
when implemented in smaller geometry processes.
An 8-bit, 500MS/s, digitally calibrated folding ADC was designed in TSMC
0.18mm. A second prototype, 9-bit 400MS/s, was designed in ST 90nm. This ADC uses
novel folders to reduce thermal noise.
The major accomplishments of this work are:
Ā· The creation of a new folding ADC architecture that is digitally dominated
allowing large transistor mismatch to be tolerated so that small devices
can be utilized in the signal path.
Ā· The development of modeling techniques, to investigate and analyze the
effects of transistor mismatch, folder linearity and redundancy in ADCs.
Ā· The design of a new folder circuit topology that decreases the required
power consumption for a given noise budget.
Ā· The design of a resistor ladder DAC that uses a unique resistor layout to
allow any shape ladder to be designed.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/58426/1/ibogue_1.pd
Multi-gigabit CMOS analog-to-digital converter and mixed-signal demodulator for low-power millimeter-wave communication systems
The objective of the research is to develop high-speed ADCs and mixed-signal demodulator for multi-gigabit communication systems using millimeter-wave frequency bands in standard CMOS technology. With rapid advancements in semiconductor technologies, mobile communication devices have become more versatile, portable, and inexpensive over the last few decades. However, plagued by the short lifetime of batteries, low power consumption has become an extremely important specification in developing mobile communication devices. The ever-expanding demand of consumers to access and share information ubiquitously at faster speeds requires higher throughputs, increased signal-processing functionalities at lower power and lower costs. In todayās technology, high-speed signal processing and data converters are incorporated in almost all modern multi-gigabit communication systems. They are key enabling technologies for scalable digital design and implementation of baseband signal processors. Ultimately, the merits of a high performance mixed-signal receiver, such as data rate, sensitivity, signal dynamic range, bit-error rate, and power consumption, are directly related to the quality of the embedded ADCs. Therefore, this dissertation focuses on the analysis and design of high-speed ADCs and a novel broadband mixed-signal demodulator with a fully-integrated DSP composed of low-cost CMOS circuitry. The proposed system features a novel dual-mode solution to demodulate multi-gigabit BPSK and ASK signals. This approach reduces the resolution requirement of high-speed ADCs, while dramatically reducing its power consumption for multi-gigabit wireless communication systems.PhDGee-Kung Chang - Committee Chair; Chang-Ho Lee - Committee Member; Geoffrey Ye Li - Committee Member; Paul A. Kohl - Committee Member; Shyh-Chiang Shen - Committee Membe
Recommended from our members
A Discrete-Time Technique for Linearity Enhancement of Wideband Receivers
A new signal processing technique is introduced to enhance the linearity performance of wideband radio frequency (RF) receivers. The proposed technique combines the advancements in mixer first architectures with a library of binary sequences as local oscillator signals to enable wide instantaneous bandwidth and high linearity for the RF receiver. To do so, N-bit pseudo-random-binary-sequences (PRBS) are used as local oscillator signals. The RF input signal is multiplied with the PRBS at the mixer and then averaged over the full sequence. This in effect reduces the amplitude of the signal and improves the overall linearity of the system. In order to enable full reconstruction of the input signal N channels are used with each employing a shifted version of a PRBS.
The effect of the proposed technique on different aspects of the system performance such as noise and linearity is discussed. In addition, the effect of nonidealities stemming from hardware implementation on the overall performance are studied. A prototype integrated circuit (IC) is implemented in 130\,nm CMOS technology to demonstrate the feasibility of the proposed technique. The design procedure of each circuit block is described and simulation results are used to evaluate the performance. The device is fabricated and characterized using a custom data acquisition system. Measurement results show good agreement with the expected values from simulation and analytical analysis.
Calibration techniques are introduced to minimize the effect of DC offsets, gain mismatches, and timing skews. Modifications to the implemented CMOS circuit are proposed to enable such calibrations and further enhance the overall performance of the system. The requirements for the precision of calibration techniques are derived and used to find the specifications of circuit block that are designed to enable these techniques. Calibration of DC offsets along with gain mismatches is carried out for the fabricated IC and results are shown. A digitally assisted technique is proposed to enable the calibration of timing skews. In addition, a review of additional implementation shortcomings that can affect the system performance are reviewed. Finally, a conclusion of the dissertation is presented along with potential future work for further enhancement of the system performance