Flexible Receivers in CMOS for Wireless Communication

Consumers are pushing for higher data rates to support more services that are introduced in mobile applications. As an example, a few years ago video-on-demand was only accessed through landlines, but today wireless devices are frequently used to stream video. To support this, more flexible network solutions have merged in 4G, introducing new technical problems to the mobile terminal. New techniques are thus needed, and this dissertation explores five different ideas for receiver front-ends, that are cost-efficient and flexible both in performance and operating frequency. All ideas have been implemented in chips fabricated in 65 nm CMOS technology and verified by measurements. Paper I explores a voltage-mode receiver front-end where sub-threshold positive feedback transistors are introduced to increase the linearity in combination with a bootstrapped passive mixer. Paper II builds on the idea of 8-phase harmonic rejection, but simplifies it to a 6-phase solution that can reject noise and interferers at the 3rd order harmonic of the local oscillator frequency. This provides a good trade-off between the traditional quadrature mixer and the 8- phase harmonic rejection mixer. Furthermore, a very compact inductor-less low noise amplifier is introduced. Paper III investigates the use of global negative feedback in a receiver front-end, and also introduces an auxiliary path that can cancel noise from the main path. In paper IV, another global feedback based receiver front-end is designed, but with positive feedback instead of negative. By introducing global positive feedback, the resistance of the transistors in a passive mixer-first receiver front-end can be reduced to achieve a lower noise figure, while still maintaining input matching. Finally, paper V introduces a full receiver chain with a single-ended to differential LNA, current-mode downconversion mixers, and a baseband circuity that merges the functionalities of the transimpedance amplifier, channel-select filter, and analog-to-digital converter into one single power-efficient block

Inductorless LNA and Harmonic-rejection Mixer for Wideband Direct-conversion Receiver

In this master thesis, combinations of noise-canceling LNA and harmonic-rejection mixers are investigated and compared to find an optimal inductorless receiver front-end for low-band (600-960MHz) FDD LTE-A network. The work was carried out in a modem development project at Ericsson Modems, Lund. Three receiver versions with different harmonic rejection techniques are compared in terms of noise figure (NF) and power consumption and the receiver with 6 LO phases is selected for optimization. The LNA combines noise cancellation for matching stage and nonlinearity cancellation for output stages so both low noise figure and high linearity are achieved. The final circuit show great potential for FDD LTE-A system with support up to 3 aggregated carriers for higher bandwidth. Low NF at 1.62 dB after the LNA and 1.75 dB after the mixer are observed from 0.4-1GHz. The LNA IIP2 is above 12 dBm and robust with process and temperature. Gain switching with possible reduction of 6 and 12 dB is integrated and the LNA linearity is not significantly suffered by low gain. Input return loss (S11) is better than -12dB regardless of gain, number of carriers and temperature (-30 – 110°C). Inductorless operation saves a lot of chip area and avoid dead package area, which then save cost and make the solution competitive.This master’s thesis done at Ericsson Modem aimed to investigate an inductorless receiver front-end for low-band LTE-A user terminals. The circuit combined noise-canceling technique and push-pull stage for LNA and harmonic-rejection technique for mixer, so three main issues of inductorless operation are solved. The issues include LNA noise and linearity, and noise folding effect caused by 3rd harmonics of LO signals

SAW-Less Digitally-Assisted Receivers

Today’s wireless devices, like our smartphones, are able to handle multiple standards and bands for different applications, such as Bluetooth, Wi-Fi and data-voice communications. However, the cost of a modern transceiver is becoming mainly dominated by the large number of off-chip passive components, like Duplexers and SAW filters, needed to distinguish the desired signal among many interferences. Addressing the challenges that arise from the lack of RF filtering, a SAW-less architecture represents an interesting solution to reduce the platform complexity. This thesis proposes a feasible solution based on a SAW-less RF front-end able to meet the standard requirements and a digital system tailored to the RF path. The digital architecture, which represents the main topic of this thesis, is described in detail and experimentally tested to validate the proposed solutions

HIGH PERFORMANCE CMOS WIDE-BAND RF FRONT-END WITH SUBTHRESHOLD OUT OF BAND SENSING

In future, the radar/satellite wireless communication devices must support multiple standards and should be designed in the form of system-on-chip (SoC) so that a significant reduction happen on cost, area, pins, and power etc. However, in such device, the design of a fully on-chip CMOS wideband receiver front-end that can process several radar/satellite signal simultaneously becomes a multifold complex problem. Further, the inherent high-power out-of-band (OB) blockers in radio spectrum will make the receiver more non-linear, even sometimes saturate the receiver. Therefore, the proper blocker rejection techniques need to be incorporated. The primary focus of this research work is the development of a CMOS high-performance low noise wideband receiver architecture with a subthreshold out of band sensing receiver. Further, the various reconfigurable mixer architectures are proposed for performance adaptability of a wideband receiver for incoming standards. Firstly, a high-performance low- noise bandwidthenhanced fully differential receiver is proposed. The receiver composed of a composite transistor pair noise canceled low noise amplifier (LNA), multi-gate-transistor (MGTR) trans-conductor amplifier, and passive switching quad followed by Tow Thomas bi-quad second order filter based tarns-impedance amplifier. An inductive degenerative technique with low-VT CMOS architecture in LNA helps to improve the bandwidth and noise figure of the receiver. The full receiver system is designed in UMC 65nm CMOS technology and measured. The packaged LNA provides a power gain 12dB (including buffer) with a 3dB bandwidth of 0.3G – 3G, noise figure of 1.8 dB having a power consumption of 18.75mW with an active area of 1.2mm*1mm. The measured receiver shows 37dB gain at 5MHz IF frequency with 1.85dB noise figure and IIP3 of +6dBm, occupies 2mm*1.2mm area with 44.5mW of power consumption. Secondly, a 3GHz-5GHz auxiliary subthreshold receiver is proposed to estimate the out of blocker power. As a redundant block in the system, the cost and power minimization of the auxiliary receiver are achieved via subthreshold circuit design techniques and implementing the design in higher technology node (180nm CMOS). The packaged auxiliary receiver gives a voltage gain of 20dB gain, the noise figure of 8.9dB noise figure, IIP3 of -10dBm and 2G-5GHz bandwidth with 3.02mW power consumption. As per the knowledge, the measured results of proposed main-high-performancereceiver and auxiliary-subthreshold-receiver are best in state of art design. Finally, the various viii reconfigurable mixers architectures are proposed to reconfigure the main-receiver performance according to the requirement of the selected communication standard. The down conversion mixers configurability are in the form of active/passive and Input (RF) and output (IF) bandwidth reconfigurability. All designs are simulated in 65nm CMOS technology. To validate the concept, the active/ passive reconfigurable mixer configuration is fabricated and measured. Measured result shows a conversion gain of 29.2 dB and 25.5 dB, noise figure of 7.7 dB and 10.2 dB, IIP3 of -11.9 dBm and 6.5 dBm in active and passive mode respectively. It consumes a power 9.24mW and 9.36mW in passive and active case with a bandwidth of 1 to 5.5 GHz and 0.5 to 5.1 GHz for active/passive case respectively

Wide-band channel sounding in the bands above 2GHz

Modem telecommunication services require increasing data rates for both mobile and fixed applications. At frequencies in the range 2.5 GHz to 6 GHz physical constraints on the size of equipment result in antenna with moderate directivity typically with an antenna beam width of 20 degrees or greater. Thus building and ground clutter is present within the first Fresnel zones of the antenna system which gives rise to multi-path propagation. This multi-path propagation (average delay and RMS delay spread) has been investigated using a wideband FMCW channel sounder that is capable of operation at a number of frequencies. The channel sounder has been based upon a parallel architecture sounder operating within the 2 GHz band with a number of frequency conversion modules to translate operation to the new frequency bands under study. Two primary configurations have been explored. In the first of these, propagation has been measured simultaneously within the 2.5 GHz, 3.4 GHz and 5.7 GHz bands. This is believed to be novel and original. In the second configuration four parallel channels operating within the 5.7 GHz band may be operated simultaneously. This configuration supports multiple antennas at the receiver. To support the work in the bands from 2.5 GHz to 6 GHz wideband discone antenna have been designed and fabricated. A system to provide relative gain and phase calibration for up to four antennas has been developed and demonstrated. This is also believed to represent a novel method of performing antenna and array calibration. Finally, the frequency converters have been used in conjunction with additional components to provide an FMCพ sounder operating within the 60 GHz Oxygen absorption band. This work is novel in that up to 1 GHz of spectrum can be swept. To support this work a significant number of microwave components have been designed and developed. In particular a novel wide band balanced X3 multiplier and a novel impedance-matched amplitude-equaliser (to provide amplifier gain-slope equalisation) has been developed. Channel soundings have been performed at three frequencies simultaneously using band specific and common antenna. The average delay and RMS delay spread have been demonstrated to be essentially frequency independent for the environments evaluated

대역 외 방해신호에 내성을 가지는 광대역 수신기에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 공과대학 전기·컴퓨터공학부, 2018. 2. 남상욱.In this thesis, a study of wideband receivers as one of the practical SDR receiver implementations is presented. The out-of-band interference signal (or blocker), which is the biggest problem of the wideband receiver is investigated, and have studied how to effectively remove it. As a result of reviewing previous studies, we have developed a wideband receiver based on the current-mode receiver structure and attempted to eliminate the blocker. The contents of the step-by-step research are as follows. First, attention was paid to the linearity of a low-noise transconductance amplifier (LNTA), which is the base block of current-mode receivers. In current-mode receivers, the LNTA should have a high transconductance (Gm) value to achieve a low noise figure, but a high Gm value results in low linearity. To solve this trade-off, we proposed a linearization method of transconductors. The proposed technique eliminates the third-order intermodulation distortion (IMD3) in a feed-forward manner using two paths. A transconductor having a transconductance of 2Gm is disposed in the main path, and an amplifier having a gain of ∛2 and a Gm-sized transconductor are located in the auxiliary path. This structure allows for some fundamental signal loss but cancel the IMD3 component at the output. As a result, the entire transconductor circuit can have high linearity due to the removed IMD3 component. We have designed a reconfigurable high-pass filter using a linearized transconductor and have demonstrated its performance. The fabricated circuit achieved a high input-referred third-order intercept point(IIP3) performance of 19.4 dBm. Then, a further improved linearized transconductor is designed. Since the linearized transconductors have a high noise figure due to the additional circuitry used for linearization, we have proposed a more suitable form for application to LNTA through noise figure analysis. The improved LNTA is designed to operate in low noise mode when there is no blocker, and can be switched to operate in high linearity mode when the blocker exists. We also applied noise cancelling techniques to the receiver to improve the noise figure performance of the wideband receiver circuit. A feedback path has been added to the current-mode receiver structure consisting of the LNTA, the mixer and the baseband transimpedance amplifier (TIA), and the noise signal can be detected using this path. This feedback path also maintains the input matching of the receiver to 50 Ω in a wide bandwidth. By adding an auxiliary path to the receiver, the in-band signal is amplified and the detected noise is removed from the baseband. The completed circuit exhibited wideband performance from 0.025 GHz to 2 GHz and IIP3 performance of -6.9 dBm in the high linearity mode. Finally, we designed a double noise-cancelling wideband receiver circuit by improving the performance of a wideband receiver with high immunity to blocker signals. In previous receivers, the LNTA was operated in two modes depending on the situation. In the improved receiver, the Gm ratio of the linearized LNTA was changed and the RF noise-cancelling technique was applied. The input matching and noise cancelling scheme introduced in the previous circuit was also applied and a wideband receiver circuit was designed to perform double noise-cancelling. As a result, the linearization and noise-cancellation of LNTA could be achieved at the same time, and the completed receiver circuit showed high IIP3 performance of 5 dBm with minimum noise figure of 1.4 dB. In conclusion, this thesis proposed a linearization technique for transconductor circuit and designed a wideband receiver based on current-mode receiver. The designed receiver circuit experimentally verified that it has low noise figure performance and high IIP3 performance and is tolerant to out-of-band blocker signals.Chapter 1. Introduction 1 1.1. Motivation of Wideband Receiver Architecture 2 1.2. Challenges in Designing Wideband Receiver 7 1.3. Prior Researches 13 1.3.1. N-Path Filter 14 1.3.2. Feed-Forward Blocker Filtering 16 1.3.3. Current-Mode Receiver 18 1.4. Research Objectives and Thesis Organization 22 Chapter 2. Transconductor Linearization Technique and Design of Tunable High-pass Filter 24 2.1. Transconductor Linearization Technique 27 2.2. Design of Tunable High-pass Filter 36 2.3. Measurement Results 41 2.4. Conclusions 46 Chapter 3. Wideband Noise-Cancelling Receiver Front-End Using Linearized Transconductor 47 3.1. Low-Noise Transconductance Amplifier Based on Linearized Transconductor 49 3.2. Wideband Noise-Cancelling Receiver Architecture 58 3.3. Measurement Results 64 3.4. Conclusions 70 Chapter 4. Blocker-Tolerant Wideband Double Noise-Cancelling Receiver Front-End 71 4.1. Linearized Noise-Cancelling Low-Noise Transconductance Amplifier 73 4.2. Wideband Double Noise-Cancelling Receiver Front-End 83 4.3. Measurement Results 90 4.4. Conclusions 97 Chapter 5. Conclusions 98 Bibliography 102 Abstract in Korean 112Docto

Reconfigurable Receiver Front-Ends for Advanced Telecommunication Technologies

The exponential growth of converging technologies, including augmented reality, autonomous vehicles, machine-to-machine and machine-to-human interactions, biomedical and environmental sensory systems, and artificial intelligence, is driving the need for robust infrastructural systems capable of handling vast data volumes between end users and service providers. This demand has prompted a significant evolution in wireless communication, with 5G and subsequent generations requiring exponentially improved spectral and energy efficiency compared to their predecessors. Achieving this entails intricate strategies such as advanced digital modulations, broader channel bandwidths, complex spectrum sharing, and carrier aggregation scenarios. A particularly challenging aspect arises in the form of non-contiguous aggregation of up to six carrier components across the frequency range 1 (FR1). This necessitates receiver front-ends to effectively reject out-of-band (OOB) interferences while maintaining high-performance in-band (IB) operation. Reconfigurability becomes pivotal in such dynamic environments, where frequency resource allocation, signal strength, and interference levels continuously change. Software-defined radios (SDRs) and cognitive radios (CRs) emerge as solutions, with direct RF-sampling receivers offering a suitable architecture in which the frequency translation is entirely performed in digital domain to avoid analog mixing issues. Moreover, direct RF- sampling receivers facilitate spectrum observation, which is crucial to identify free zones, and detect interferences. Acoustic and distributed filters offer impressive dynamic range and sharp roll off characteristics, but their bulkiness and lack of electronic adjustment capabilities limit their practicality. Active filters, on the other hand, present opportunities for integration in advanced CMOS technology, addressing size constraints and providing versatile programmability. However, concerns about power consumption, noise generation, and linearity in active filters require careful consideration.This thesis primarily focuses on the design and implementation of a low-voltage, low-power RFFE tailored for direct sampling receivers in 5G FR1 applications. The RFFE consists of a balun low-noise amplifier (LNA), a Q-enhanced filter, and a programmable gain amplifier (PGA). The balun-LNA employs noise cancellation, current reuse, and gm boosting for wideband gain and input impedance matching. Leveraging FD-SOI technology allows for programmable gain and linearity via body biasing. The LNA's operational state ranges between high-performance and high-tolerance modes, which are apt for sensitivityand blocking tests, respectively. The Q-enhanced filter adopts noise-cancelling, current-reuse, and programmable Gm-cells to realize a fourth-order response using two resonators. The fourth-order filter response is achieved by subtracting the individual response of these resonators. Compared to cascaded and magnetically coupled fourth-order filters, this technique maintains the large dynamic range of second-order resonators. Fabricated in 22-nm FD-SOI technology, the RFFE achieves 1%-40% fractional bandwidth (FBW) adjustability from 1.7 GHz to 6.4 GHz, 4.6 dB noise figure (NF) and an OOB third-order intermodulation intercept point (IIP3) of 22 dBm. Furthermore, concerning the implementation uncertainties and potential variations of temperature and supply voltage, design margins have been considered and a hybrid calibration scheme is introduced. A combination of on-chip and off-chip calibration based on noise response is employed to effectively adjust the quality factors, Gm-cells, and resonance frequencies, ensuring desired bandpass response. To optimize and accelerate the calibration process, a reinforcement learning (RL) agent is used.Anticipating future trends, the concept of the Q-enhanced filter extends to a multiple-mode filter for 6G upper mid-band applications. Covering the frequency range from 8 to 20 GHz, this RFFE can be configured as a fourth-order dual-band filter, two bandpass filters (BPFs) with an OOB notch, or a BPF with an IB notch. In cognitive radios, the filter’s transmission zeros can be positioned with respect to the carrier frequencies of interfering signals to yield over 50 dB blocker rejection