An effective modeling framework for the analysis of interconnects subject to line-edge roughness

This letter proposes a complete and efficient simulation framework to assess the effects of line-edge roughness appearing in on-chip lines. The modeling approach consists of three steps. First, a stochastic macromodel is created for the per-unit-length RLGC parameters of the line. Secondly, random conductor edge profiles are generated using randomized splines. These are combined with the stochastic macromodel to readily provide place-dependent RLGC parameters. Finally, the resulting nonuniform transmission line is analyzed by means of a fast and accurate perturbation technique. To validate the proposed approach, a statistical analysis of the response of a coupled inverted embedded microstrip line is carried out for different roughness parameters

Influence of base and photoacid generator on deprotection blur in extreme ultraviolet photoresists and some thoughts on shot noise

A contact-hole deprotection blur metric has been used to monitor the deprotection blur of an experimental open platform resist (EH27) as the wt % of base and photoacid generator (PAG) were varied. A six times increase in base wt % is shown to reduce the size of successfully patterned 1:1 line-space features from 52 to 39 nm without changing deprotection blur. Corresponding isolated line edge roughness is reduced from 6.9 to 4.1 nm. A two times increase in PAG wt % is shown to improve 1:1 line-space patterning from 47 to 40 nm without changing deprotection blur or isolated line edge roughness. A discussion of improved patterning performance as related to shot noise and deprotection blur concludes with a speculation that the spatial distribution of PAG molecules has been playing some role, perhaps a dominant one, in determining the uniformity of photogenerated acids in the resists that have been studied. © 2008 American Vacuum Society

Intrinsic parameter fluctuations in decananometer MOSFETs introduced by gate line edge roughness

In this paper, we use statistical three-dimensional (3-D) simulations to study the impact of the gate line edge roughness (LER) on the intrinsic parameters fluctuations in deep decananometer (sub 50 nm) gate MOSFETs. The line edge roughness is introduced using a Fourier synthesis technique based on the power spectrum of a Gaussian autocorrelation function. In carefully designed simulation experiments, we investigate the impact of the rms amplitude /spl Delta/ and the correlation length /spl Lambda/ on the intrinsic parameter fluctuations in well scaled, but simple devices with fixed geometry as well as the channel length and width dependence of the fluctuations at fixed LER parameters. For the first time, we superimpose in the simulations LER and random discrete dopants and investigate their relative contribution to the intrinsic parameter fluctuations in the investigated devices. For particular MOSFET geometries, we were able to identify the regions where each of these two sources of intrinsic parameter fluctuations dominates

Enhanced Resolution of Poly-(Methyl Methacrylate) Electron Resist by Thermal Processing

Granular nanostructure of electron beam resist had limited the ultimate resolution of electron beam lithography. We report a thermal process to achieve a uniform and homogeneous amorphous thin film of poly methyl methacrylate electron resist. This thermal process consists of a short time-high temperature backing process in addition to precisely optimized development process conditions. Using this novel process, we patterned arrays of holes in a metal film with diameter smaller than 5nm. In addition, line edge roughness and surface roughness of the resist reduced to 1nm and 100pm respectively.Comment: 8 pages, 4 figure

Modeling of novel resist technologies

In response to the difficulties posed by the resolution, line edge roughness, sensitivity (RLS) trade-off to traditional chemically amplified resist (CAR) systems used for extreme ultraviolet lithography, a number of novel resist technologies have been proposed. In this paper, the effect of quencher loading on three resist technologies is analyzed via an error propagation-based resist simulator. In order of increasing novelty as well as complexity, they are: Conventional CAR with quencher, CAR with photodecomposable base, and PSCAR 2.0, a CAR system with photodecomposable base as well as an EUV-activated UV-sensitive resist component. Simulation finds the more complicated resist systems trade in an increase in resist stochastics for improved deprotection slopes, yielding a net benefit in terms of line width roughness

Analytical modeling and 3D finite element simulation of line edge roughness in scatterometry

The influence of edge roughness in angle resolved scatterometry at periodically structured surfaces is investigated. A good description of the radiation interaction with structured surfaces is crucial for the understanding of optical imaging processes like, e.g. in photolithography. We compared an analytical 2D model and a numerical 3D simulation with respect to the characterization of 2D diffraction of a line grating involving structure roughness. The results show a remarkably high agreement. The diffraction intensities of a rough structure can therefore be estimated using the numerical simulation result of an undisturbed structure and an analytically derived correction function. This work allows to improve scatterometric results for the case of practically relevant 2D structures

Polymer Bound Photobase Generators And Photoacid Generators For Pitch Division Lithography

The semiconductor industry is pursuing several process options that provide pathways to printing images smaller than the theoretical resolution limit of 193 nm projection scanners. These processes include double patterning, side wall deposition and pitch division. Pitch doubling lithography (PDL), the achievement of pitch division by addition of a photobase generator (PBG) to typical 193 nm resist formulations was recently presented. 1 Controlling the net acid concentration as a function of dose by incorporating both a photoacid generator (PAG) and a PBG in the resist formulation imparts a resist dissolution rate response modulation at twice the frequency of the aerial image. Simulation and patterning of 45 nm half pitch L/S patterns produced using a 90 nm half pitch mask were reported. 2 Pitch division was achieved, but the line edge roughness of the resulting images did not meet the current standard. To reduce line edge roughness, polymer bound PBGs and polymer bound PAGs were investigated in the PDL resist formulations. The synthesis, purification, analysis, and functional performance of various polymers containing PBG or PAG monomers are described herein. Both polymer bound PBG with monomeric PAG and polymer bound PAG with monomeric PBG showed a PDL response. The performance of the polymer bound formulations is compared to the same formulations with small molecule analogs of PAG and PBG.Chemical Engineerin