35 research outputs found
ANALISIS PENGHAMBAT PENYELESAIAN STUDI MAHASISWA S1 PROGRAM STUDI PENDIDIKAN TEKNIK MESIN JURUSAN PENDIDIKAN TEKNIK DAN KEJURUAN FAKULTAS KEGURUAN DAN ILMU PENDIDIKAN UNIVERSITAS SEBELAS MARET SURAKARTA
The purpose of the research is to acquire knowledge about the internal factors and
external factors are a barrier to completion of the study in thesis writing student S1 in PTM
JPTK UNS Surakarta. The source in this research are all students Mechanical Engineering
Education JPTK FKIP UNS Surakarta class of 2006, 2007, and 2008. The sample is taken by
using sampling purposive technique. The sample in this research are students Mechanical
Engineering Education JPTK FKIP UNS Surakarta class of 2006, 2007, and 2008 which take
courses thesis. The most dominant factor that inhibits completion of studies students PTM S1
JPTK FKIP UNS Surakarta, among others: (1) Internal factors is health factors, fatigue
factors, and psychological factors. (2) External factors is guidance by professors factors,
family factors, friends factors, student reference factors, and administrative thesis factors.
Key words: inhibitor analysis, study completion, student S1, thesi
STUDI PEMANFAATAN CAMPURAN SERBUK TEMPURUNG KELAPA-ALUMINIUM SEBAGAI MATERIAL ALTERNATIF KAMPAS REM SEPEDA MOTOR NON-ASBESTOSSTUDI PEMANFAATAN CAMPURAN SERBUK TEMPURUNG KELAPA-ALUMINIUM SEBAGAI MATERIAL ALTERNATIF KAMPAS REM SEPEDA MOTOR NON-ASBESTOS
Serbuk tempurung kelapa dapat digunakan sebagai alternatif bahan kampas
rem non-asbes sepeda motor. Dalam penelitian ini, pada komposisi serbuk tempurung
kelapa 20%, serbuk aluminium 40%, resin 40% memiliki angka yang paling mendekati
dengan kampas rem pembanding. Komposisi serbuk tempurung kelapa 20%, serbuk
aluminium 40%, resin 40% memiliki angka keausan 0,071.10-7 mm2/kg. Komposisi
serbuk tempurung kelpa 20%, serbuk aluminium 40%, resin 40% memiliki angka
kekerasan 16,8 kgf/mm2. Dengan melakukan variasi komposisi akan didapat angka
keausan dan kekerasan yang paling optimum. Variasi komposisi serbuk tempurung
kelapa sangat berpengaruh terhadap angka keausan dan angka kekerasan sampel
kampas rem.
Kata kunci : kampas rem non asbes, serbuk tempurung kelapa, serbuk aluminium,
kekerasan, keausan, kampas rem
PENGARUH SUDUT PENYAYATAN DAN JUMLAH MATA SAYAT ENDMILL CUTTER TERHADAP TINGKAT KEKASARAN PERMUKAAN BAJA ST 40 HASIL PEMESINAN CNC MILLING TOSURO KONTROL GSK 983 Ma-H
The purpose of this study is to determine: (1) the effect of endmill cutter primary angel to
the roughness level of steel ST 40 machining result by Tosuro CNC Milling controlled by GSK
983 Ma-H. (2) The effect of the endmill cutter flute amount to the roughness level of steel ST 40
machining result by Tosuro CNC Milling controlled by GSK 983 Ma-H. (3) a combination of
primary angel and the flute amount of endmill cutter which produces the smallest level of
roughness. This study is an experiment that uses two-factor variables (angle incision and the
number of eyes slice endmill cutter) and one dependent variable (the level of surface roughness).
This study was conducted at the Machining Practices Laboratory of SMK Warga Surakarta for
the formation of Test Objects and implementation of the machining process using Tosuro CNC
Milling controlled by GSK Ma-H. The level of the surface roughness conducted at Engineering
Materials Laboratory of Mechanical Engineering Diploma, The Faculty of Engineering,
GadjahMada University. The research method used in this study is an experimental method with
analytic descriptive analytical techniques. The results showed that there was primary angel and
the flute amount of endmill cutter effect to the roughness level of steel ST 40 machining result
by Tosuro CNC Milling controlled by GSK 983 Ma-H. The smallest combination of primary
angel and the flute amount of endmill cutter toward the roughness level of steel ST 40 machining
results process by TS 218 CNC Milling is on the interaction between primary angel of 5° and 4
flutes of endmill cutter is equal to 0,2013 µm and the greatest of the roughness level of steel ST
40 machining results process by TS 218 CNC Milling is on the interaction between primary
angel of 10° and 2 flutes of endmill cutter is equal to 0,4691 µm. The more the amount of
endmill cutter the smaller the level of the roughness
ANALISIS KESIAPAN MAHASISWA DALAM MELAKSANAKAN PRAKTIK INDUSTRI PROGRAM STUDI PENDIDIKAN TEKNIK MESIN JPTK FKIP UNS
The purpose of this research was to know the students readiness of Mechanical
Engineering Education Study Program JPTK FKIP UNS in implementating industry practice
and the value of indicators which obtained.
This research is a quantitative descriptive. Research subjects were students of
Mechanical Engineering Education Study Program JPTK FKIP UNS 2009, as many as 56
students. The research sample as many as 48 students. Sampling technique was proportionate
random sampling. Sampling technique was proportionate random sampling. Techniques of
data collection are by questionnaire and interview. Testing of the validity instrument was
conducted based on the Pearson's Product Moment Correlation. Reliability test instrument
used Cronbach's Alpha.
The results showed that students readiness of Mechanical Engineering Education
Study Program JPTK FKIP UNS 2009 in implementating industry practice in terms of
condition tonus of the body was 78,65 (high), state of body function was 85,00 (very high),
intelligence was 79,90 (high), motivation was 72,08 (high), interests was 80,83 (very high),
attitudes was 73,17 (high), and talents was 73,85 (high). In general, the student of Mechanical
Engineering Education Study Program JPTK FKIP UNS 2009 ready to implemented Industry
Practices.
Key words: Student Readiness, Industry Practice, Mechanical Engineering Education Study
Progra
KARAKTERISASI TINGKAT KEKASARAN PERMUKAAN BAJA ST 40 HASIL PEMESINAN CNC MILLING ZK 7040 EFEK DARI KECEPATAN PEMAKANAN (FEED RATE) DAN AWAL WAKTU PEMBERIAN PENDINGIN
The purpose of this research was to determine the level surface roughness
characterization of steel ST 40 results ZK 7040 CNC Milling machining effect feed
rate and the early timing of cooling.
This research was conducted at SMK WARGA Surakarta Laboratory.
Machining process using ZK 7040 CNC Milling machines with control SIEMENS
SINUMERIK 802S. Data obtained by measuring the level of roughness of the
workpiece using a SURFCODER SE-1700 at Bahan Teknik D3, Univesitas Gadjah
Mada Laboratory. This research method using descriptive analysis with independent
variable were feed rates and the early timing of cooling, dependent variable was
levels of surface roughness of steel ST 40.
The results on the feedrate 0.11 mm / rev, 0.13 mm / rev and 0.15 mm / rev
indicates that the higher the feedrate is used to produce the level of the rough
workpiece roughness. In the early timing of the air 10 minutes, 15 minutes and, 20
minutes showed that the longer the first timing of cooling used in the CNC machining
process Milling ZK 7040 on steel ST 40, would result in the level of the rough
workpiece roughness. This research resulted in varying levels of surface roughness
between N6 to N8.
The level of roughness of the workpiece machining CNC Milling results ZK
7040 on steel ST 40 that the smallest on the conditions before the beginning of the
cooling at feed rate 0.11 mm / rev and the early cooling time 10 minutes is equal to
1.616 μm, while the greatest rudeness occurs the feed rate of 0.15 mm / rev and the
early timing of the air 20 minutes is equal to 3.603 μm. The level of roughness of the
workpiece machining CNC Milling results ZK 7040 on steel ST 40 that the smallest
on the conditions after the timing of cooling on CNC milling machining process ZK
7040 occurred at a feed rate of 0.11 mm / rev and the early timing of cooling after 10
minutes is equal to 1.855 μm while the roughness of the greatest place on the feed
rate of 0.15 mm / rev and the early timing of cooling after 20 minutes is equal to
5.782 μm.
Keywords: feed rate, early timing of air, surface roughness, steel ST 40, CNC Millin
PENGARUH VARIASI PUTARAN MESIN DAN PEMANASAN BAHAN BAKAR BENSIN MELALUI PIPA KAPILER BERSIRIP RADIAL DI DALAM UPPER TANK RADIATOR TERHADAP KONSUMSI BAHAN BAKAR BENSIN PADA MESIN TOYOTA KIJANG
The result of this research shows that the effect the usage of heating gasoline fuel
through a capillary tube which is radial finned in the upper tank radiator at engine speed 1000
r.p.m., 2000 r.p.m., and 3000 r.p.m.. Average consumption at engine speed 1000 r.p.m.
normal Toyota Kijang average consumption 32,066×10-3
cc per cycle. With the use of
heating fuel use 3 copper pipe with fins spaced 10 mm fuel consumption by 25,174×10-3
cc
per cycle. Fuel consumption decreased by 6,892×10-3
cc per cycle or 21,58%. At engine
speed 2000 r.p.m. normal Toyota Kijang average consumption 38,487×10-3
cc per cycle.
With the use of heating fuel use 3 copper pipe with fins spaced 10 mm fuel consumption by
28,121×10-3
cc per cycle. Fuel consumption decreased by 10,366×10-3
cc per cycle or
26,93%. At engine speed 3000 r.p.m. normal Toyota Kijang average consumption
36,783×10-3
cc per cycle. With the use of heating fuel use 3 copper pipe with fins spaced 10
mm fuel consumption by 31,187×10-3
cc per cycle. Fuel consumption decreased by 5,596×10-
3
per cycle or 15,21%. The conclusion of this research is the usage of fuel heating using three
copper tubes with the range between the fins is 10 mm in the upper tank of radiator can
reduce the biggest lowers fuel consumption on the Engine of Toyota Kijang 1989.
Keywords: r.p.m., heating fuel, capillary tube, radial fin, upper tank radiator, fuel
consumption of gasolin
OPTIMASI PARAMETER PROSES PEMESINAN CNC MILLING TERHADAP KEKASARAN PERMUKAAN KAYU JATI DENGAN METODE TAGUCHI
Nur Firstiawan. PARAMETER OPTIMIZATION OF MACHINING CNC
MILLING PROCESS OF SURFACE ROUGHNESS TEAK WOOD WITH METHOD
2
TAGUCHI. Thesis, Surakarta: The Faculty of Teacher Training and Education. Sebelas
Maret University, September 2012.
The purpose of this research is to know: (1) Effect of spindle speed variation, feedrate,
depth of cut and direction of the wood grain pieces (longitudinal, radial and tangential) to the
level of surface roughness result type CNC milling machining process ZK 7040 at teak wood
material. (2) Knowing which parameters that produce optimal roughness values on CNC
milling machining process on the material type ZK 7040 at teak wood material, using the
Taguchi method.
Teak wood machining process using CNC milling machine type 7040 with the ZK
control SIEMENS SINUMERIK 802S in SMK SAKTI Gemolong. The testing of moisture
content done in Laboratory of Materials, Civil Engineering, Sebelas Maret University.
Surface roughness test was done in metrology laboratory, Mechanical Engineering
Diploma Program, Vocational School, Gadjah Mada University. Optimization methods used
in this study the Taguchi method. TAGUCHI ANOVA (Analysis of Taguchi Varian) in Minitab
15 software help to determine the performance characteristics of the machining parameters.
The results of CNC milling machining process on the material type ZK 7040 teak was:
(1) higher spindle speed, will produce a surface roughness values less ie at level 3 = 3000
rpm; highe feedrate, will produce a surface roughness values greater ie at level 3 = 1200
mm/min; higher depth of cut,will produce value greater surface roughness is at level 3 = 6
mm, and more dry wood on the variation of direction wood grain pieces, would result in the
value of the smaller surface roughness is at level 1 = direction tangential cutting. (2)
Parameters that yield optimal surface roughness values are at 3000 rpm spindle rotation
speed, feedrate 400 mm/min, depth of cut 2 mm and tangential cutting direction. The feedrate
has the most effect with delta ratio S/N 3,78 and the direction of cutting wood has the smallest
contribution is a delta ratio S/N 1,92. (3) The optimal roughness is 4,12 ± 0,42 μm.
Key words: Wood machining, CNC milling, surface roughness, and Taguchi
metho
PENGARUH VARIASI WATERGLASS TERHADAP KADAR AIR DAN KADAR LEMPUNG PADA PASIR CETAK
This paper presents an effect of variation waterglass on moisture degree and clay degree in
sand casting. The held as the word in sand casting used is waterglass with a variation of 0%,
15%, 25%, and 40%. Sand casting mixture on the sand river weighing 500 grams, the
addition of 10 ml of water, and the addition of waterglass based on the variations that have
been determined. Research carried out is descriptive research with experimental methods.
The result show that the moisture degree and increasing clay degree. The higher addition of
waterglass on molding sands increasing moisture degree. The resulting moisture degree is
1.50%, 5.18%, 6.48%, 7.14%. The higher addition of waterglass on molding sands
increasing moisture degree. The resulting clay degree was 5.44%, 12.80%, 17.68%, 26.64%.
Keywords : waterglass, molding sands, moisture degree, clay degre
PENGARUH KECEPATAN PEMAKANAN DAN KADAR AIR TERHADAP KEKASARAN PERMUKAAN PADA PROSES MILLING CNC 3 AXIS DENGAN MATERIAL KAYU JATI
There are many factors influencing the quality of products that are produced from
wood machinery. Those influencing factors are the feedrate and moisture content.The results
of this research was: (1) Reduction of feedrate of 3 axis CNC milling process with teak wood
material, would be resulted the smllest surface roughness. (2) Reduction of moisture content
of 3 axis CNC milling process with teak wood material, would be resulted the smallest surface
roughness. (3) The surface roughness of 3 axis CNC milling processes with feedrate variation
0.2, 0.4 and 0.6 mm / rev and the moisture content 0%, 17% and 67% would be produce a
level surface roughness between N7 to N11. The smallest surface roughness occurs in
interaction feedrate 0.2 mm / rev with a moisture content 0% at 5.54 μm, whereas the rate of
degradation surface roughness occurs interaction feedrate 0.6 mm / rev with moisture content
67% at 16.10 μm . The surface appearanceof 3 axis CNC millingproceses a fuzzy grain,
loosened grains, chipped grains and chip mark.
Keywords: feedrate, moisture content, CNC milling, surface roughness
HUBUNGAN ANTARA MOTIVASI BELAJAR DAN PRESTASI BELAJAR DENGAN MINAT MENJADI GURU MAHASISWA PTM JPTK FKIP UNS SURAKARTA TAHUN AKADEMIK 2011/2012.
Tujuan penelitian ini adalah: (1) Untuk mengetahui hubungan antara motivasi
belajar dengan minat menjadi guru mahasiswa Program Studi Pendidikan Teknik Mesin JPTK
FKIP UNS Surakarta Tahun Akademik 2011/2012, (2) Untuk mengetahui hubungan antara
prestasi belajar dengan minat menjadi guru mahasiswa Program Studi Pendidikan Teknik Mesin
JPTK FKIP UNS Surakarta Tahun Akademik 2011/2012, (3) Untuk mengetahui hubungan
secara bersama- sama antara motivasi belajar dan prestasi belajar dengan minat menjadi guru
mahasiswa Program Studi Pendidikan Teknik Mesin JPTK FKIP UNS Surakarta Tahun
Akademik 2011/2012. Penelitian ini berbentuk kuantitatif dengan menggunakan metode
deskriptif korelasional. Populasi penelitian ini adalah mahasiswa Program Studi Pendidikan
Teknik Mesin JPTK FKIP UNS Surakarta angkatan tahun 2009 sejumlah 56 mahasiswa. Sampel
penelitian diambil 48 mahasiswa yang diambil menggunakan proportionate random sampling.
Untuk memperoleh data prestasi belajar menggunakan metode dokumentasi, untuk memperoleh
data motivasi belajar dan minat menjadi guru menggunakan metode angket. Teknik analisis data
yang digunakan adalah analisis korelasi dan regresi linear ganda. Hasil analisis data yaitu: (1)
Ada hubungan yang signifikan antara motivasi belajar dengan minat menjadi guru mahasiswa
Program Studi Pendidikan Teknik Mesin JPTK FKIP UNS Surakarta Tahun Akademik
2011/2012. Hal ini ditunjukkan dari hasil perhitungan pada n = 48 dan taraf signifikansi 5%
diperoleh r
x1y > r tabel
atau 0,5182 > 0,284. (2) Ada hubungan yang signifikan antara prestasi
belajar dengan minat menjadi guru mahasiswa Program Studi Pendidikan Teknik Mesin JPTK
FKIP UNS Surakarta Tahun Akademik 2011/2012. Hal ini ditunjukkan dari hasil perhitungan
pada n = 48 dan taraf signifikansi 5% diperoleh r
x1y > r tabel
atau 0,5398 > 0,284. (3) Ada
hubungan yang signifikan secara bersama- sama antara motivasi belajar dan prestasi belajar
dengan minat menjadi guru mahasiswa Program Studi Pendidikan Teknik Mesin JPTK FKIP
UNS Surakarta Tahun Akademik 2011/2012. Hal ini ditunjukkan dari hasil perhitungan pada dk
pembilang = 2, dk penyebut = 45 dan taraf signifikansi 5% diperoleh F
hitung
> F tabel
atau 9,29 >
3,20.
Kata Kunci: motivasi belajar, prestasi belajar, minat guru