17,678 research outputs found
Digital Switching in the Quantum Domain
In this paper, we present an architecture and implementation algorithm such
that digital data can be switched in the quantum domain. First we define the
connection digraph which can be used to describe the behavior of a switch at a
given time, then we show how a connection digraph can be implemented using
elementary quantum gates. The proposed mechanism supports unicasting as well as
multicasting, and is strict-sense non-blocking. It can be applied to perform
either circuit switching or packet switching. Compared with a traditional space
or time domain switch, the proposed switching mechanism is more scalable.
Assuming an n-by-n quantum switch, the space consumption grows linearly, i.e.
O(n), while the time complexity is O(1) for unicasting, and O(log n) for
multicasting. Based on these advantages, a high throughput switching device can
be built simply by increasing the number of I/O ports.Comment: 24 pages, 16 figures, LaTe
Sialons as high temperature insulators
Sialons were evaluated for application as high temperature electrical insulators in contact with molybdenum and tungsten components in hard vacuum applications. Both D.C. and variable frequency A.C. resistivity data indicate the sialons to have electrical resistivity similar to common oxide in the 1000 C or higher range. Metallographic evaluations indicate good bonding of the type 15R ALN polytype to molybdenum and tungsten. The beta prime or modified silicon nitride phase was unacceptable in terms of vacuum stability. Additives effect on electrical resistivity. Similar resistivity decreases were produced by additions of molybdenum or tungsten to form cermets. The use of hot pressing at 1800 C with ALN, Al2 O3 and Si3N4 starting powders produced a better product than did a combination of SiO2 and AIN staring powders. It was indicated that sialons will be suitable insulators in the 1600K range in contact with molybdenum or tungsten if they are produced as a pure ceramic and subsequently bonded to the metal components at temperatures in the 1600K range
A 0.8 V T Network-Based 2.6 GHz Downconverter RFIC
A 2.6 GHz downconverter RFIC is designed and implemented using a 0.18 μm CMOS standard process. An important goal of the design is to achieve the high linearity that is required in WiMAX systems with a low supply voltage. A passive T phase-shift network is used as an RF input stage in a Gilbert cell to reduce supply voltage. A single supply voltage of 0.8 V is used with a power consumption of 5.87 mW. The T network-based downconverter achieves a conversion gain (CG) of 5 dB, a single-sideband noise figure (NF) of 16.16 dB, an RF-to-IF isolation of greater than 20 dB, and an input-referred third-order intercept point (IIP3) of 1 dBm when the LO power of -13 dBm is applied
The Megamaser Cosmology Project. V. An Angular Diameter Distance to NGC 6264 at 140 Mpc
We present the direct measurement of the Hubble constant, yielding the direct
measurement of the angular-diameter distance to NGC 6264 using the HO
megamaser technique. Our measurement is based on sensitive observations of the
circumnuclear megamaser disk from four observations with the Very Long Baseline
Array, the Green Bank Telescope and the Effelsberg Telescope. We also monitored
the maser spectral profile for 2.3 years using the Green Bank Telescope to
measure accelerations of maser lines by tracking their line-of-sight velocities
as they change with time. The measured accelerations suggest that the systemic
maser spots have a significantly wider radial distribution than in the
archetypal megamaser in NGC 4258. We model the maser emission as arising from a
circumnuclear disk with orbits dominated by the central black hole. The best
fit of the data gives a Hubble constant of 689 km s
Mpc, which corresponds to an angular-diameter distance of 14419
Mpc. In addition, the fit also gives a mass of the central black hole of
(3.090.42) . The result demonstrates the
feasibility of measuring distances to galaxies located well into the Hubble
flow by using circumnuclear megamaser disks.Comment: 29 pages, 8 figures, Accepted by Ap
Combustion: Structural interaction in a viscoelastic material
The effect of interaction between combustion processes and structural deformation of solid propellant was considered. The combustion analysis was performed on the basis of deformed crack geometry, which was determined from the structural analysis. On the other hand, input data for the structural analysis, such as pressure distribution along the crack boundary and ablation velocity of the crack, were determined from the combustion analysis. The interaction analysis was conducted by combining two computer codes, a combustion analysis code and a general purpose finite element structural analysis code
- …