760 research outputs found
Low flow venovenous bypasses in small dogs and pediatric patients undergoing replacement of the liver
A venovenous bypass for transplantation of the liver was developed and evaluated in dogs and applied clinically, with flows that averaged less than 500 milliliters per minute. Fatal pulmonary emboli were seen in two of 40 experiments. The venovenous flow in the four pediatric recipients was 200 to 1,200 milliliters per minute, and there were no complications
WHO Takes Action to Promote the Health of Refugees and Migrants
Migration is a defining issue of our time, with 1 billion migrants globally, of whom 258 million have crossed borders. Climate change and political instability propel ever-greater displacement, with major detriments to health. Policies that fail to prevent human trafficking or guarantee essential services undermine Universal Health Coverage (UHC) and the global pledge to “leave no one behind.” The World Health Assembly should robustly implement WHO’s Global Action Plan (GAP) on the Health of Refugees and Migrants.ugees and Migrants
A New Method to Measure Portal Venous and Hepatic Arterial Blood Flow Patients Intraoperatively
The intraoperative measurement of the afferent circulation of the liver, namely the hepatic artery flow and portal venous flow was carried out upon 14 anesthetized patients having carcinoma in the splanchnic area,
mainly in the head of the pancreas by means of transit time ultrasonic volume flowmeter. The hepatic
artery flow, portal venous flow and total hepatic flow were 0.377±0.10; 0.614±0.21; 0.992±0.276 l/min respectively
VOICE QUALITY ASSESSMENT DURING VOICE TRANSMISSION\ud BY VARIOUS NETWORK TECHNOLOGIES\ud
This paper deals with the voice quality system assessment including calculation of the noise floor during voice transmission by various network technologies. Voice over Internet Protocol (VoIP) development presupposes solution of the problems related to effective voice transmission with required transmission parameters (Quality of Services - QoS). One of the mechanisms that may be used for assurance of service quality in IP networks is the QoS model. The QoS model is used to evaluate the VoIP quality and to design the VoIP networks. The voice quality may be determined using the passive method – E-model – which respects the used codec, the packet loss and the delay or the jitter. Attention is also paid to the calculation of the noise floor emphasizing the possibilities of the signal-to-noise ratio estimating. This paper also presents results of experimental verification of the designed solution implementation functionality.\ud
Описано систему оценки качества голоса включая определение порога шума в течении передачи голоса различными сетевыми технологиями. Развитие передачи голоса интернет протоколом (VoIP) предпочитает решение проблем относящихся к эффективной передачи голоса с требованными параметрами передачи (качество сервиса - QoS). Одним из механизмов, который может быть использован для обеспечения качества сервиса в IP сетях является QoS модель. QoS модели используются для оценки качества VoIP и для проектирования VoIP сетей. Качество голоса может быть определено с использованием пасивного метода – E-модели, которая отражает использован кодек, потерю пакетов, опаздывание и его колебание. Внимание уделяется определению порога шума подчеркивающее возможности оценки отношения сигнал-шум. Приведены результаты экспериментальной проверки функционирования имплементации предложенного решения.\u
Nanofibers
Cellulose is the most available biopolymer on earth existent in wood and other lignocellulosic sources, which can be isolated as nanofibers to reinforce composites. The aim of this chapter overview was to explain cellulose nanofibers’ preparation methods from different plant sources. The chemical treatment of cellulose fibers including dilute alkali swelling, acid and base hydrolysis, and bleaching was carried out followed by a mechanical method to isolate nanofibers. In this study, the effect of few palnt source variations and mechanical processes used in extraction procedure on nanofibers morphology, crystallinity, and chemical composition was evaluated. Characteristics of extracted cellulose nanofibers obtained from different plant sources were presented as well
Synthesis and Characterization of Nanostructured Oxide Layers on Ti-Nb-Zr-Ta and Ti-Nb-Zr-Fe Biomedical Alloys
Nanoporous/nanotubular complex oxide layers were developed on high-fraction β phase quaternary Ti-Nb-Zr-Ta and Ti-Nb-Zr-Fe promising biomedical alloys with a low elasticity modulus. Surface modification was achieved by electrochemical anodization aimed at the synthesis of the morphology of the nanostructures, which exhibited inner diameters of 15–100 nm. SEM, EDS, XRD, and current evolution analyses were performed for the characterization of the oxide layers. By optimizing the process parameters of electrochemical anodization, complex oxide layers with pore/tube openings of 18–92 nm on Ti-10Nb-10Zr-5Ta, 19–89 nm on Ti-20Nb-20Zr-4Ta, and 17–72 nm on Ti-29.3Nb-13.6Zr-1.9Fe alloys were synthesized using 1 M H3PO4 + 0.5 wt% HF aqueous electrolytes and 0.5 wt% NH4F + 2 wt% H20 + ethylene glycol organic electrolytes
Cloud-based robots and intelligent space teleoperation tools
Despite an idea of robotic system teleoperation is a relatively old concept, here we present its enhancements heading to an interconnection of teleoperation and collecting relevant information from the environment where robots act. This environment should be an intelligent space featured with various devices and sensors, which allows to obtain, preprocess and stores data in the cloud. Those data should provide relevant information for teleoperator or directly for robots, which act autonomously. For this purpose, we developed cloud-based tools, named Telescope v2. It is a platform-independent system for remote monitoring and controlling various systems. In this paper, we introduce this system, its abilities, and compare it with its network-based ancestor, Telescope v1. We analyze measurements of latency and response time when our new system is used for teleoperation in different places equipped with various Internet bandwidths
Bioink properties before, during and after 3D bioprinting
Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration and interaction with the material. A calibrated computational framework is able to predict the tissue development and maturation and to optimize the bioprinting input parameters such as the starting material, the initial cell loading and the construct geometry. In this contribution relevant bioink properties are reviewed and discussed on the example of most popular bioprinting approaches. The effect of cells on hydrogel processing and vice versa is highlighted. Furthermore, numerical approaches were reviewed and implemented for depicting the cellular mechanics within the hydrogel as well as for prediction of mechanical properties to achieve the desired hydrogel construct considering cell density, distribution and material-cell interaction
- …