9,670 research outputs found
Evaluation of shear mounted elastomeric damper
Viton-70 elastomeric shear mounted damper was built and tested on a T-55 power turbine spool in the rotor's high speed balancing rig. This application of a shear mounted elastomeric damper demonstrated for the first time, the feasibility of using elastomers as the primary rotor damping source in production turbine engine hardware. The shear damper design was selected because it was compatible with actual gas turbine engine radial space constraints, could accommodate both the radial and axial thrust loads present in gas turbine engines, and was capable of controlled axial preload. The shear damper was interchangeable with the production T-55 power turbine roller bearing support so that a direct comparison between the shear damper and the production support structure could be made. Test results show that the Viton-70 elastomer damper operated successfully and provided excellent control of both synchronous and nonsynchronous vibrations through all phases of testing up to the maximum rotor speed of 16,000 rpm. Excellent correlation between the predicted and experienced critical speeds, mode shapes and log decrements for the power turbine rotor and elastomer damper assembly was also achieved
Internal rotor friction instability
The analytical developments and experimental investigations performed in assessing the effect of internal friction on rotor systems dynamic performance are documented. Analytical component models for axial splines, Curvic splines, and interference fit joints commonly found in modern high speed turbomachinery were developed. Rotor systems operating above a bending critical speed were shown to exhibit unstable subsynchronous vibrations at the first natural frequency. The effect of speed, bearing stiffness, joint stiffness, external damping, torque, and coefficient of friction, was evaluated. Testing included material coefficient of friction evaluations, component joint quantity and form of damping determinations, and rotordynamic stability assessments. Under conditions similar to those in the SSME turbopumps, material interfaces experienced a coefficient of friction of approx. 0.2 for lubricated and 0.8 for unlubricated conditions. The damping observed in the component joints displayed nearly linear behavior with increasing amplitude. Thus, the measured damping, as a function of amplitude, is not represented by either linear or Coulomb friction damper models. Rotordynamic testing of an axial spline joint under 5000 in.-lb of static torque, demonstrated the presence of an extremely severe instability when the rotor was operated above its first flexible natural frequency. The presence of this instability was predicted by nonlinear rotordynamic time-transient analysis using the nonlinear component model developed under this program. Corresponding rotordynamic testing of a shaft with an interference fit joint demonstrated the presence of subsynchronous vibrations at the first natural frequency. While subsynchronous vibrations were observed, they were bounded and significantly lower in amplitude than the synchronous vibrations
Synergistic relationships among remote-sensing and geophysical media: Geological and hydrological applications
The synergistic relationships among LANDSAT imagery, Skylab photographs, and aerial photographs were useful for establishing areas of near surface bedrock. Lineaments were located on LANDSAT imagery and aerial photographs during 1978 and near surface water tables were to be located during 1980. Both of these subjects can be identified by remote sensing methods more reliably than individual outcrops, which are small and occur in a wide variety of environments with a wide range of responses. Bedrock outcrops themselves could not be resolved by any of the data sources used, nor did any combination of data sources specifically identify rock at the ground surface. The data sources could not simply be combined mathematically to produce a visual image of probable areas of near surface bedrock. Outcrops and near surface bedrock had to be verified visually at the site. Despite these drawbacks, a procedure for locating areas of near surface bedrock within which actual surface outcrops may occur was developed
Adaptive antenna arrays for satellite communications: Design and testing
When two separate antennas are used with each feedback loop to decorrelate noise, the antennas should be located such that the phase of the interfering signal in the two antennas is the same while the noise in them is uncorrelated. Thus, the antenna patterns and spatial distribution of the auxiliary antennas are quite important and should be carefully selected. The selection and spatial distribution of auxiliary elements is discussed when the main antenna is a center fed reflector antenna. It is shown that offset feeds of the reflector antenna can be used as auxiliary elements of an adaptive array to suppress weak interfering signals. An experimental system is designed to verify the theoretical analysis. The details of the experimental systems are presented
Apollo-11 lunar sample information catalogue
The Apollo 11 mission is reviewed with emphasis on the collection of lunar samples, their geologic setting, early processing, and preliminary examination. The experience gained during five subsequent missions was applied to obtain physical-chemical data for each sample using photographic and binocular microscope techniques. Topics discussed include: binocular examination procedure; breccia clast dexrriptuons, thin section examinations procedure typical breccia in thin section, typical basalt in thin section, sample histories, and chemical and age data. An index to photographs is included
Solar pond power plant feasibility study for Davis, California
The feasibility of constructing a solar pond power plant at Davis, California was studied. Site visits, weather data compilation, soil and water analyses, conceptual system design and analyses, a material and equipment market survey, conceptual site layout, and a preliminary cost estimate were studied. It was concluded that a solar pond power plant is technically feasible, but economically unattractive. The relatively small scale of the proposed plant and the high cost of importing salt resulted in a disproportionately high capital investment with respect to the annual energy production capacity of the plant. Cycle optimization and increased plant size would increase the economical attractiveness of the proposed concept
Electromagnetic properties of material coated surfaces
The electromagnetic properties of material coated conducting surfaces were investigated. The coating geometries consist of uniform layers over a planar surface, irregularly shaped formations near edges and randomly positioned, electrically small, irregularly shaped formations over a surface. Techniques to measure the scattered field and constitutive parameters from these geometries were studied. The significance of the scattered field from these geometries warrants further study
Vibration characteristics of ring-stiffened orthotropic shells of revolution
Computer program solves vibration modes and frequencies of thin shells of revolution having general meridional curvature and orthotropic elastic properties in order to evaluate the dynamic behavior of structures with thin shelled components
Why undertake a pilot in a qualitative PhD study? Lessons learned to promote success
YesBackground
Pilot studies can play an important role in qualitative studies. Methodological and practical issues can be shaped and refined by undertaking pilots. Personal development and researchers’ competence are enhanced and lessons learned can inform the development and quality of the main study. However, pilot studies are rarely published, despite their potential to improve knowledge and understanding of the research.
Aim
To present the main lessons learned from undertaking a pilot in a qualitative PhD study.
Discussion
This paper draws together lessons learned when undertaking a pilot as part of a qualitative research project. Important methodological and practical issues identified during the pilot study are discussed including access, recruitment, data collection and the personal development of the researcher. The resulting changes to the final study are also highlighted.
Conclusion
Sharing experiences of and lessons learned in a pilot study enhances personal development, improves researchers’ confidence and competence, and contributes to the understanding of research
- …