Detection of a relic X-ray jet in Cygnus A

We present a 200 ks Chandra ACIS-I image of Cygnus A, and discuss a long linear feature seen in its counterlobe. This feature has a non-thermal spectrum and lies on the line connecting the brighter hotspot on the approaching side and the nucleus. We therefore conclude that this feature is (or was) a jet. However, the outer part of this X-ray jet does not trace the current counterjet observed in radio. No X-ray counterpart is observed on the jet side. Using light-travel time effects we conclude that this X-ray 50 kpc linear feature is a relic jet that contains enough low-energy plasma (gamma ~ 10^3) to inverse-Compton scatter cosmic microwave background photons, producing emission in the X-rays.Comment: 4 pages. Proceedings of "High Energy Phenomena in Relativistic Outflows", held in Dublin, Ireland, September 24-28, 200

A thin rivulet or ridge subject to a uniform transverse shear stress at its free surface due to an external airflow

We use the lubrication approximation to analyse three closely related problems involving a thin rivulet or ridge (i.e. a two-dimensional droplet) of fluid subject to a prescribed uniform transverse shear stress at its free surface due to an external airflow, namely a rivulet draining under gravity down a vertical substrate, a rivulet driven by a longitudinal shear stress at its free surface, and a ridge on a horizontal substrate, and find qualitatively similar behaviour for all three problems. We show that, in agreement with previous numerical studies, the free surface profile of an equilibrium rivulet/ridge with pinned contact lines is skewed as the shear stress is increased from zero, and that there is a maximum value of the shear stress beyond which no solution with prescribed semi-width is possible. In practice, one or both of the contact lines will de-pin before this maximum value of the shear stress is reached, and so we consider situations in which the rivulet/ridge de-pins at one or both contact lines. In the case of de-pinning only at the advancing contact line, the rivulet/ridge is flattened and widened as the shear stress is increased from its critical value, and there is a second maximum value of the shear stress beyond which no solution with a prescribed advancing contact angle is possible. In contrast, in the case of de-pinning only at the receding contact line, the rivulet/ridge is thickened and narrowed as the shear stress is increased from its critical value, and there is a solution with a prescribed receding contact angle for all values of the shear stress. In general, in the case of de-pinning at both contact lines there is a critical “yield” value of the shear stress beyond which no equilibrium solution is possible and the rivulet/ridge will evolve unsteadily. In an Appendix we show that an equilibrium rivulet/ridge with prescribed flux/area is quasi-statically stable to two-dimensional perturbations

A thin rivulet or ridge subject to a uniform transverse\ud shear stress at its free surface due to an external airflow

We use the lubrication approximation to analyse three closely related problems involving a thin rivulet or ridge (i.e. a two-dimensional droplet) of fluid subject to a prescribed uniform transverse shear stress at its free surface due to an external airflow, namely a rivulet draining under gravity down a vertical substrate, a rivulet driven by a longitudinal shear stress at its free surface, and a ridge on a horizontal substrate, and find qualitatively similar behaviour for all three problems. We show that, in agreement with previous numerical studies, the free surface profile of an equilibrium rivulet/ridge with pinned contact lines is skewed as the shear stress is increased from zero, and that there is a maximum value of the shear stress beyond which no solution with prescribed semi-width is possible. In practice, one or both of the contact lines will de-pin before this maximum value of the shear stress is reached, and so we consider situations in which the rivulet/ridge de-pins at one or both contact lines. In the case of de-pinning only at the advancing contact line, the rivulet/ridge is flattened and widened as the shear stress is increased from its critical value, and there is a second maximum value of the shear stress beyond which no solution with a prescribed advancing contact angle is possible. In contrast, in the case of de-pinning only at the receding contact line, the rivulet/ridge is thickened and narrowed as the shear stress is increased from its critical value, and there is a solution with a prescribed receding contact angle for all values of the shear stress. In general, in the case of de-pinning at both contact lines there is a critical “yield” value of the shear stress beyond which no equilibrium solution is possible and the rivulet/ridge will evolve unsteadily. In an Appendix we show that an equilibrium rivulet/ridge with prescribed flux/area is quasi-statically stable to two-dimensional perturbations

Alcohol and healthy ageing: a challenge for alcohol policy

Objectives: This paper presents findings of a qualitative study of older people's use of alcohol during retirement and identifies ways that an improved understanding of older people's drinking can inform policy approaches to alcohol and active and healthy ageing. Study design: Qualitative semi-structured interviews conducted with a self-selecting sample of retired people. Methods: Participants were recruited from three geographical locations in the West of Scotland. A quota sampling design was used to ensure a broad spread of participants in terms of socio-economic position, age and gender. In total 40 participants were interviewed and the data analysed thematically using Braun and Clarke's (2006) approach. Results: Amongst those who used alcohol, it was most often framed in terms of pleasure, relaxation, socialising and as a way to mark the passage of time. Alcohol was often associated with social occasions and interactions both in private and in public spaces. There were also many examples of the use of imposed routines to limit alcohol use and of a decreasing volume of alcohol being consumed as participants aged. This suggests that older people are often active in constructing what they regard as ‘healthier’ routines around alcohol use. However, processes and circumstances associated with ageing can lead to risk of social isolation and/or increased alcohol consumption. Such processes include retirement from paid work and other ‘biographical disruptions’ such as caring for a partner, bereavement and/or loss of social networks. Conclusions: These findings highlight processes that can result in changes in drinking habits and routines. Whilst these processes can be associated with a reduction or cessation of alcohol use as people age, they can also be associated with increased risk of harmful alcohol consumption. Fractured or disrupted routines, particularly those associated with bereavement or the burden of caring responsibilities, through increasing the risk of loneliness and isolation, can construct increased risk of harmful alcohol consumption. These findings reframe the pathway of risk between ageing and alcohol-related harm by highlighting the vulnerability to harmful drinking practices brought by fracture or sudden change of routine. The findings point to a role for public health in supporting the reconstruction of routines that provide structure and meaning and can be used to actively manage the benefits and harms associated with drinking

Independent Orbiter Assessment (IOA): Assessment of the life support and airlock support systems, volume 1

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. The IOA effort first completed an analysis of the Life Support and Airlock Support Systems (LSS and ALSS) hardware, generating draft failure modes and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The IOA results were then compared to the NASA FMEA/CIL baseline with proposed Post 51-L updates included. The discrepancies were flagged for potential future resolution. This report documents the results of that comparison for the Orbiter LSS and ALSS hardware. The IOA product for the LSS and ALSS analysis consisted of 511 failure mode worksheets that resulted in 140 potential critical items. Comparison was made to the NASA baseline which consisted of 456 FMEAs and 101 CIL items. The IOA analysis identified 39 failure modes, 6 of which were classified as CIL items, for components not covered by the NASA FMEAs. It was recommended that these failure modes be added to the NASA FMEA baseline. The overall assessment produced agreement on all but 301 FMEAs which caused differences in 111 CIL items

Decentralised Learning MACs for Collision-free Access in WLANs

By combining the features of CSMA and TDMA, fully decentralised WLAN MAC schemes have recently been proposed that converge to collision-free schedules. In this paper we describe a MAC with optimal long-run throughput that is almost decentralised. We then design two \changed{schemes} that are practically realisable, decentralised approximations of this optimal scheme and operate with different amounts of sensing information. We achieve this by (1) introducing learning algorithms that can substantially speed up convergence to collision free operation; (2) developing a decentralised schedule length adaptation scheme that provides long-run fair (uniform) access to the medium while maintaining collision-free access for arbitrary numbers of stations

Influence of coal thermoplastic properties on coking pressure generation: Part 2 – A study of binary coal blends and specific additives

A number of coal blends and pitch/coal blends were evaluated using rheometry, thermogravimetric analysis and microscopy to confirm and further elucidate the coking pressure mechanism previously proposed by Duffy et al. (2007) [1]. We confirm that blending a low rank, high fluidity, low coking pressure coal, with a high rank, low fluidity, high coking pressure coal can significantly reduce the coking pressure associated with the latter. Interestingly, blending does not necessarily result in a fluidity that is midway between that of the two coals; sometimes the fluidity of the blend is less than that of the low fluidity coal, especially when the coals are significantly different in rank. This occurs because the increase in complex viscosity (η*) through resolidification of the low rank, high fluidity coal counteracts the reduction in η* resulting from softening of the high rank, low fluidity coal. It has also been confirmed that the η* of the resultant blend can be estimated from the η* of each component coal using a logarithmic additivity rule commonly employed for polymer blends. Polarised light microscopy has indicated that the degree of mixing between coals of different rank is minimal, with fusion restricted to the particle surface. It is therefore inappropriate to think of such a coal blend in the same way as a single coal, since each component coal behaves relatively independently. This limited fusion is important for understanding the coking pressure mechanism for blends. It is proposed here that the lower rank coal, which softens at lower temperature, is able to expand into the interparticle voids between the high rank coal that is yet to soften, and these voids can create channels for volatiles to traverse. Then, and importantly, when the high rank coal begins to expand, the pore structure developed in the resolidified structures of the low rank coal can facilitate removal of volatiles, while the resolidified material may also act as a suitable sorbent for volatile matter. This is considered to be the primary mechanism by which coal blending is able to alleviate coking pressure, and applies to addition of inert material also. Addition of a coal tar pitch was found to increase fluidity but also to extend the thermoplastic range to lower temperatures. This caused an increase in the swelling range, which was accompanied by a long plateau in η*, a feature which has previously been observed for certain high fluidity, high pressure coals. Elasticity and η* at the onset of expansion were also higher for both the pitch impregnated coals and the high pressure blends, which supports previous findings for singly charged high pressure coals, and confirms the potential use of such criteria for identifying potentially dangerous coals/blends. © 2009 Elsevier Ltd. All rights reserved

Travelling-wave similarity solutions for an unsteady shear-stress-driven dry patch in a flowing film

We investigate unsteady flow of a thin film of Newtonian fluid around a symmetric slender dry patch moving with constant velocity on an inclined planar substrate, the flow being driven by a prescribed constant shear stress at the free surface of the film (which would be of uniform thickness in the absence of the dry patch). We obtain a novel unsteady travelling-wave similarity solution which predicts that the dry patch has a parabolic shape and that the film thickness increases monotonically away from the dry patch

Heat and fluid flow in a scraped-surface heat exchanger containing a fluid with temperature-dependent viscosity

Scraped-surface heat exchangers (SSHEs) are extensively used in a wide variety of industrial settings where the continuous processing of fluids and fluid-like materials is involved. The steady non-isothermal flow of a Newtonian fluid with temperature-dependent viscosity in a narrow-gap SSHE when a constant temperature difference is imposed across the gap between the rotor and the stator is investigated. The mathematical model is formulated and the exact analytical solutions for the heat and fluid flow of a fluid with a general dependence of viscosity on temperature for a general blade shape are obtained. These solutions are then presented for the specific case of an exponential dependence of viscosity on temperature. Asymptotic methods are employed to investigate the behaviour of the solutions in several special limiting geometries and in the limits of weak and strong thermoviscosity. In particular, in the limit of strong thermoviscosity (i.e., strong heating or cooling and/or strong dependence of viscosity on temperature) the transverse and axial velocities become uniform in the bulk of the flow with boundary layers forming either just below the blade and just below the stationary upper wall or just above the blade and just above the moving lower wall. Results are presented for the most realistic case of a linear blade which illustrate the effect of varying the thermoviscosity of the fluid and the geometry of the SSHE on the flow

Comentarios a la ponencia "Igualdades, desigualdades y derechos", presentada por Mirta Lobato

Teniendo en cuenta -como advierte Mirta Lobato a los comentaristas- que cuando habla de desigualdades en su ponencia se refiere a que "el trabajo es el eje articulador de estas reflexiones", y sin dejar de reconocer la importancia que cabe a los otros temas y sujetos sobre los que tan bien desarrolla su exposición, quiero centrarme en un grupo que estoy estudiando desde hace unos años, como es el de los inmigrantes limítrofes a la Argentina de fin de siglo XX e inicios del XXI. Para ello, voy a analizar brevemente -como así lo exigen las reglas del comentario- a estos sujetos sociales, a quienes, como también ella afirma, ya los habríamos de encontrar censalmente a inicios del siglo pasado, aunque su visibilidad fuera menor porque aún no habían arribado a Buenos Aires; es decir, al escenario donde "las cosas suceden".Fil: Benencia, Roberto Rodolfo. Universidad de Buenos Aires; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentin