5,001 research outputs found
An analytical evaluation of airfoil sections for helicopter rotor applications
An analytical technique was used to evaluate airfoils for helicopter rotor application. This technique permits assessment of the influences of airfoil geometric variations on drag divergence Mach number at lift coefficients from near zero to near maximum lift. Analytical results presented in this paper indicate the compromises in drag divergence Mach number which result from changes in (1) thickness ratio, (2) location of maximum thickness, (3) leading-edge radius, (4) camber addition, and (5) location of maximum camber of NACA four- and five-digit-series airfoils and some 6-series airfoils of potential interest for helicopters. Examples of airfoil sections which combine several of the geometric changes favorable to both advancing and retreating section performance have been presented
Two-dimensional aerodynamic characteristics of three rotorcraft airfoils at Mach numbers from 0.35 to 0.90
Three airfoils designed for helicopter rotor application were investigated in the Langley 6- by 28-inch Transonic Tunnel to determine the two dimensional aerodynamic characteristics at Mach numbers from 0.34 to 0.88 and respective Reynolds numbers from about 4.4 x 10(6) power to 9.5 x 10(6) power. The airfoils have thickness-to-chord ratios of 0.08, 0.10, and 0.12. Trailing-edge reflex was applied to minimize pitching moment. The maximum normal-force coefficient of the RC(3)-12 airfoil is from 0.1 to 0.2 higher, depending on Mach number M, than that of the NACA 0012 airfoil tested in the same facility. The maximum normal-force coefficient of the RC(3)-10 is about equal to that of the NACA 0012 at Mach numbers to 0.40 and is higher than that of the NACA 0012 at Mach numbers above 0.40. The maximum normal force coefficient of the RC(3)-08 is about 0.19 lower than that of the NACA 0012 at a Mach number of 0.35 and about 0.05 lower at a Mach number of 0.54. The drag divergence Mach number of the RC(3)-08 airfoil at normal-force coefficients below 0.1 was indicated to be greater than the maximum test Mach number of 0.88. At zero lift, the drag-divergence Mach numbers of the RC(3)-12 and the RC(3)-10 are about 0.77 and 0.82, respectively
Aerodynamic characteristics of three helicopter rotor airfoil sections at Reynolds number from model scale to full scale at Mach numbers from 0.35 to 0.90
An investigation was conducted in the Langely 6 by 28 inch transonic tunnel to determine the two dimensional aerodynamic characteristics of three helicopter rotor airfoils at Reynolds numbers from typical model scale to full scale at Mach numbers from about 0.35 to 0.90. The model scale Reynolds numbers ranged from about 700,00 to 1,500,000 and the full scale Reynolds numbers ranged from about 3,000,000 to 6,600,000. The airfoils tested were the NACA 0012 (0 deg Tab), the SC 1095 R8, and the SC 1095. Both the SC 1095 and the SC 1095 R8 airfoils had trailing edge tabs. The results of this investigation indicate that Reynolds number effects can be significant on the maximum normal force coefficient and all drag related parameters; namely, drag at zero normal force, maximum normal force drag ratio, and drag divergence Mach number. The increments in these parameters at a given Mach number owing to the model scale to full scale Reynolds number change are different for each of the airfoils
Experimental investigation of three helicopter rotor airfoils designed analytically
Three helicopter rotor airfoils designed analytically were investigated in a wind tunnel at Mach numbers from about 0.30 to 0.90 and Reynolds from about 0.8 to 2.3 x 10 to the 6th power. The airfoils had thickness-to-chord ratios of 0.08, 0.10, and 0.12 with maximum thickness at 40 percent chord. The camber distribution of each section was the same with maximum camber at 35 percent chord. The 10-percent-thick airfoil was also investigated at Reynolds numbers from 4.8 to 9.4 x 10 to the 6th power. The drag divergence Mach number of the 10-percent-thick airfoil is about 0.83 at a normal-force coefficient of 0 and about 0.72 at a normal-force coefficient of 0.6 at Reynolds numbers near 9 x 10 to the 6th power. The maximum normal-force coefficient is slightly less than that of the NACA 0012 airfoil tested in the same facility. The results indicate that a qualitative evaluation of the drag divergence can be made at normal-force coefficients up to the onset of boundary-layer separation by analytically predicting the onset of sonic flow at the airfoil crest. The qualitative results are conservative with respect to experimental values with the experimental drag divergence Mach number up to 0.05 higher than that indicated by analysis
Low speed aerodynamic characteristics of NACA 6716 and NACA 4416 airfoils with 35 percent-chord single-slotted flaps
An investigation was conducted in a low-turbulence pressure tunnel to determine the two-dimensional lift and pitching-moment characteristics of an NACA 6716 and an NACA 4416 airfoil with 35-percent-chord single-slotted flaps. Both models were tested with flaps deflected from 0 deg to 45 deg, at angles of attack from minus 6 deg to several degrees past stall, at Reynolds numbers from 3.0 million to 13.8 million, and primarily at a Mach number of 0.23. Tests were also made to determine the effect of several slot entry shapes on performance
Influence of an aperture on the performance of a two-degree-of-freedom iron-cored spherical permanent-magnet actuator
Abstract—This paper describes a computational and experimental study of a two-degree-of-freedom spherical permanent-magnet actuator equipped with an iron stator. In particular, it considers the effect of introducing an aperture in the stator core to facilitate access to the armature. The resultant magnetic field distribution in the region occupied by the stator windings, the net unbalanced radial force, and the resulting reluctance torque are determined by three-dimensional magnetostatic finite-element
analysis. The predicted reluctance torque is validated experimentally, and its implications on actuator performance are described
Recommended from our members
Rapid Manufactured Textiles
Rapid Manufacturing (RM) is increasingly becoming a viable manufacturing process due
to dramatic advantages that are achievable in the area of design complexity. Through the
exploration of the design freedom, this paper introduces the concept of manufacturing textiles for
potential smart and high performance textile applications. This paper discusses the current
limitations associated with the manufacture of textiles through RM and presents a novel
methodology for the generation of 3D conformal RM textile articles. The paper concludes that
through RM it is entirely possible to manufacture a structure that incorporates drape and free
movement properties directly comparable to conventional textiles.Mechanical Engineerin
Subglacial drainage processes at a High Arctic polythermal valley glacier
Peer reviewedPublisher PD
Recommended from our members
Impact Absorbent Rapid Manufactured Structures (IARMS)
Rapid Manufacturing (RM) is increasingly becoming a viable manufacturing process due
to dramatic advantages that it facilitates in the area of design complexity. Through the
exploration of the design freedom afforded by RM, this paper introduces the concept and initial
research surrounding Impact Absorbent Rapid Manufactured Structures (IARMS), with an
application in sports personal protective equipment (PPE). Designs are based on the cellular
structure of foams; the inherent advantages of the cellular structure are used as a basis to create
IARMS that have the potential to be optimised for a specific impact absorbent response. The
paper provides some initial results from compression testingMechanical Engineerin
- …