Memory effects of carbon nanotubes as charge storage nodes for floating gate memory applications

Author name used in this publication: J. Y. Dai2005-2006 > Academic research: refereed > Publication in refereed journalVersion of RecordPublishe

Investigation on the Dispersal Characteristics of Liquid Breakup in Vacuum

This work presents an experimental study on the dispersal characteristics of a liquid jet ejecting into vacuum. The liquid breaking experiments of several kinds of liquid under different pressure and temperature conditions are carried out in a flash chamber. The stability of the jet and the sizes of the droplets or the icing particles formed during liquid flashing dispersing are analyzed. The influences of the superheat degree, spray velocity, and the mass of the volatile liquid mixing in the nonvolatile liquid on these characteristics are discussed. Moreover, the applicability of the two definitions of superheat degree is discussed. The results show that the superheat degree is an important parameter influencing the pattern of the breaking liquid, and the jet velocity has a large influence on the distribution of particle sizes. In addition, mixing some volatile liquid with nonvolatile liquid can enhance the dispersion of the latter

Synthesis and memory effect study of Ge nanocrystals embedded in LaAlO₃ high-k dielectrics

Author name used in this publication: P. F. LeeAuthor name used in this publication: J. Y. Dai2004-2005 > Academic research: refereed > Publication in refereed journalVersion of RecordPublishe

Simulation of dynamic loading in centrifuge modeling for suction bucket foundations

Suction bucket foundations are widely used in the offshore platform for the exploitation of the offshore petroleum and natural gas resources in the Bohai Bay of China. During winter seasons, ice sheets formed in Bohai Bay will impose strong impact and result in strong vibration on the platform. The measured frequency of the structural vibration of the platforms is 0.8 similar to 1.0 Hz. This paper describes a dynamic loading device developed on the geotechnical centrifuge at Tsinghua University and its application in modeling suction bucket foundation under the equivalent ice-induced vibration loadings

Solidly Mounted Resonators with Carbon Nanotube Electrodes for Biosensing Applications

The work reported here shows a direct experimental comparison of the sensitivities of AlN solidly mounted resonators (SMR)-based biosensors fabricated with standard metal electrodes and with carbon nanotube electrodes. SMRs resonating at frequencies around 1.75 GHz have been fabricated, some devices using a thin film of multi-wall carbon nanotubes (CNTs) as the top electrode material and some identical devices using a chromium/gold electrode. Protein solutions with different concentrations were loaded on the top of the resonators and their responses to mass-load from physically adsorbed coatings were investigated. Results show that resonators using CNTs as the top electrode material exhibited higher frequency change for a given load due to the higher active surface area of a thin film of interconnecting CNTs compared to that of a metal thin film electrode and hence exhibited greater mass loading sensitivity. It is therefore concluded that the use of CNT electrodes on resonators for their use as gravimetric biosensors is viable and worthwhile

AlN-based BAW resonators with CNT electrodes for gravimetric biosensing

Solidly mounted resonators (SMRs) with a top carbon nanotubes (CNTs) surface coating that doubles as an electrode and as a sensing layer have been fabricated. The influence of the CNTs on the frequency response of the resonators was studied by direct comparison to identical devices with a top metallic electrode. It was found that the CNTs introduced significantly less mass load on the resonators and these devices exhibited a greater quality factor, Q (>2000, compared to ∼1000 for devices with metal electrodes), which increases the gravimetric sensitivity of the devices by allowing the tracking of smaller frequency shifts. Protein solutions with different concentrations were loaded on the top of the resonators and their responses to mass-load from physically adsorbed coatings were investigated. Results show that resonators using CNTs as the top electrode exhibited a higher frequency change for a given load (∼0.25 MHz cm2 ng−1) compared to that of a metal thin film electrode (∼0.14 MHz cm2 ng−1), due to the lower mass of the CNT electrodes and their higher active surface area compared to that of a thin film metal electrode. It is therefore concluded that the use of CNT electrodes on resonators for their use as gravimetric biosensors is a significant improvement over metallic electrodes that are normally employed

Quantifying Inactive Lithium in Lithium Metal Batteries

Inactive lithium (Li) formation is the immediate cause of capacity loss and catastrophic failure of Li metal batteries. However, the chemical component and the atomic level structure of inactive Li have rarely been studied due to the lack of effective diagnosis tools to accurately differentiate and quantify Li+ in solid electrolyte interphase (SEI) components and the electrically isolated unreacted metallic Li0, which together comprise the inactive Li. Here, by introducing a new analytical method, Titration Gas Chromatography (TGC), we can accurately quantify the contribution from metallic Li0 to the total amount of inactive Li. We uncover that the Li0, rather than the electrochemically formed SEI, dominates the inactive Li and capacity loss. Using cryogenic electron microscopies to further study the microstructure and nanostructure of inactive Li, we find that the Li0 is surrounded by insulating SEI, losing the electronic conductive pathway to the bulk electrode. Coupling the measurements of the Li0 global content to observations of its local atomic structure, we reveal the formation mechanism of inactive Li in different types of electrolytes, and identify the true underlying cause of low Coulombic efficiency in Li metal deposition and stripping. We ultimately propose strategies to enable the highly efficient Li deposition and stripping to enable Li metal anode for next generation high energy batteries

Janus monolayers of transition metal dichalcogenides.

Structural symmetry-breaking plays a crucial role in determining the electronic band structures of two-dimensional materials. Tremendous efforts have been devoted to breaking the in-plane symmetry of graphene with electric fields on AB-stacked bilayers or stacked van der Waals heterostructures. In contrast, transition metal dichalcogenide monolayers are semiconductors with intrinsic in-plane asymmetry, leading to direct electronic bandgaps, distinctive optical properties and great potential in optoelectronics. Apart from their in-plane inversion asymmetry, an additional degree of freedom allowing spin manipulation can be induced by breaking the out-of-plane mirror symmetry with external electric fields or, as theoretically proposed, with an asymmetric out-of-plane structural configuration. Here, we report a synthetic strategy to grow Janus monolayers of transition metal dichalcogenides breaking the out-of-plane structural symmetry. In particular, based on a MoS2 monolayer, we fully replace the top-layer S with Se atoms. We confirm the Janus structure of MoSSe directly by means of scanning transmission electron microscopy and energy-dependent X-ray photoelectron spectroscopy, and prove the existence of vertical dipoles by second harmonic generation and piezoresponse force microscopy measurements