Spin-tunnel investigation of a 1/13-scale model of the NASA AD-1 oblique-wing research aircraft

The spin and recovery characteristics of a 1/13-scale model of the NASA AD-1 oblique-wing research aircraft at wing-skew positions of 0, 25, 45, and 60 deg (right wing forward) were investigated. Spins were obtained for all wing-skew positions tested. For the unskewed wing position, two spin modes were possible. One spin mode was very steep and recoveries were obtained within 1 turn or less by rudder reversal. The second spin mode was flat and fast; the angle of attack was about 75 deg and the spin rate was about 145 deg/sec (2.5 seconds per turn). For the skewed wing positions, spins were obtained only in the direction of the forward-skewed wing (right wing forward). No spins were obtained to the left when the wing was skewed with the right wing forward. Recoveries should be attempted by deflecting the rudder to full against the spin, the ailerons to full with the spin, and movement of the wings to 0 deg skew. If the wing is skewed, the recovery may not be effected until the wing skew approaches 0 deg

Pressure distribution of a twin-engine upper-surface blown jet-flap model

An investigation has been made to determine the chordwise and spanwise pressure distributions of a small-scale upper-surface blown jet-augmented flap STOL model. The model was powered by two simulated high-bypass-ratio turbofan engines mounted ahead of and above an unswept-untapered wing in a nacelle having a rectangular nozzle. The results of the investigation are presented as tabulated and plotted chordwise pressure distribution coefficients for nine spanwise stations

Spin-Tunnel Investigation of the Spinning Characteristics of Typical Single-Engine General Aviation Airplane Designs. 1. Low-Wing Model A: Effects of Tail Configurations

The effects of tail design on spin and recovery were investigated in a spin tunnel. A 1/11-scale model of a research airplane which represents a typical low-wing, single engine, light general aviation airplane was used. A tail design criterion for satisfactory spin recovery for light airplanes was evaluated. The effects of other geometric design features on the spin and recovery characteristics were also determined. Results indicate that the existing tail design criterion for light airplanes, which uses the tail damping power factor as a parameter, cannot be used to predict spin-recovery characteristics

Spin-tunnel investigation of the spinning characteristics of typical single-engine general aviation airplane designs. 2: Low-wing model A; tail parachute diameter and canopy distance for emergency spin recovery

A spin tunnel study is reported on a scale model of a research airplane typical of low-wing, single-engine, light general aviation airplanes to determine the tail parachute diameter and canopy distance (riser length plus suspension-line length) required for energency spin recovery. Nine tail configurations were tested, resulting in a wide range of developed spin conditions, including steep spins and flat spins. The results indicate that the full-scale parachute diameter required for satisfactory recovery from the most critical conditions investigated is about 3.2 m and that the canopy distance, which was found to be critical for flat spins, should be between 4.6 and 6.1 m

The Journals of Lieutenant John Pickell, 1836-1837

During the summer of 1837, virtually all military operations against the Seminoles ceased. For several months after General Thomas S. Jesup’s agreement with the Indians in March, only sporadic fighting had occurred in Florida. The Army was employed in encouraging the Indians to assemble for emigration to the West as provided by the truce and in exploring the country. At the same time, however, additional troops were arriving to resume hostilities, if this should become necessary. The Seminoles, on the other hand, used this period to delay their embarkation and at the same time to continue their attacks upon white settlements. The resumption of the war, consequently, was inevitable

Generation and measurement of nonstationary random processes technical note no. 3

Generation and measurement of nonstationary stochastic processes related to Monte Carlo studies with analog compute

The goldstone real-time connected element interferometer

Connected element interferometry (CEI) is a technique of observing a celestial radio source at two spatially separated antennas and then interfering the received signals to extract the relative phase of the signal at the two antennas. The high precision of the resulting phase delay data type can provide an accurate determination of the angular position of the radio source relative to the baseline vector between the two stations. This article describes a recently developed connected element interferometer on a 21-km baseline between two antennas at the Deep Space Network's Goldstone, California, tracking complex. Fiber-optic links are used to transmit the data to a common site for processing. The system incorporates a real-time correlator to process these data in real time. The architecture of the system is described, and observational data are presented to characterize the potential performance of such a system. The real-time processing capability offers potential advantages in terms of increased reliability and improved delivery of navigational data for time-critical operations. Angular accuracies of 50-100 nrad are achievable on this baseline

An evaluation of the Department of Health’s Health and Social Care Volunteering Fund

The Health and Social Care Volunteering Fund (HSCVF) is an innovative programme that was established in 2009 by the Department of Health (DH) to build organisational and community capacity for volunteering through a national and local grant scheme. The HSCVF has offered both funds and tailored support to health and social care projects delivered by Voluntary, Community and Social Enterprise (VCSE) organisations. The HSCVF is managed by a partnership led by Ecorys and with expertise from leading national voluntary sector organisations: Attend, Community Service Volunteers (CSV) and Primetimers. To date the HSCVF has funded a total of 157 local and national projects, of which 114 are currently live. This report presents findings from an evaluation of the HSCVF with a specific focus on the 2010/2011 national and local projects, conducted by a team from the Institute for Health & Wellbeing at Leeds Metropolitan University. It presents evidence on the extent to which, how and in what ways the HSCVF programme has built organisational and community capacity across the national and local HSCVF projects, as well as on the health and social outcomes that resulted

Emperical Tests of Acceptance Sampling Plans

Acceptance sampling is a quality control procedure applied as an alternative to 100% inspection. A random sample of items is drawn from a lot to determine the fraction of items which have a required quality characteristic. Both the number of items to be inspected and the criterion for determining conformance of the lot to the requirement are given by an appropriate sampling plan with specified risks of Type I and Type II sampling errors. In this paper, we present the results of empirical tests of the accuracy of selected sampling plans reported in the literature. These plans are for measureable quality characteristics which are known have either binomial, exponential, normal, gamma, Weibull, inverse Gaussian, or Poisson distributions. In the main, results support the accepted wisdom that variables acceptance plans are superior to attributes (binomial) acceptance plans, in the sense that these provide comparable protection against risks at reduced sampling cost. For the Gaussian and Weibull plans, however, there are ranges of the shape parameters for which the required sample sizes are in fact larger than the corresponding attributes plans, dramatically so for instances of large skew. Tests further confirm that the published inverse-Gaussian (IG) plan is flawed, as reported by White and Johnson (2011)