Performance enhancement of permeable asphalt mixtures with recycled aggregate for concrete pavement application

The incorporation of recycled concrete aggregate (RCA) in permeable asphalt mixtures (PAMs) is an efficient method of utilizing construction demolished waste. It not only conforms to the trend of building sponge cities, but also alleviates the problem of overexploitation of natural aggregate resources. As the performance of PAM containing recycled aggregate is not comparable to natural aggregate, modification treatments and the addition of hybrid fibers are adopted as two enhancement methods to improve the performance of PAM with RAC in this study. It is found that replacing natural aggregate with recycled aggregate increases the optimum asphalt content (OAC) but decreases the residual stability. The OAC is increased by 45% when the RCA ratio is 100%, whereas applying silicone resin can give a 16.2% decrease in the OAC. Enhancing RCA with silicone resin can increase the water stability to be comparable with natural aggregate. Moreover, with modification treatment using calcium hydroxide solution, the mechanical strength of PAM is enhanced to even higher than that of natural coarse aggregate mixture alone. Improvements in both mechanical strength and water stability are also achieved by strengthening recycled aggregate with cement slurry, although the performance is less effective than using silicone resin. With the increase in the content of RCA, the permeability coefficients of PAM first decrease and then exhibit an increasing trend. The results indicate that the PAM with RCA and modification treatments can perform satisfactorily as a pavement material in practice. Applying probable modification, PAM incorporating RCA meets the criteria for use in concrete pavement applications

Detection of Hepatitis B virus in serum and liver of chickens

Hepatitis B virus (HBV) is one of the most important human pathogens. Its existence in food animals could present a significant threat to public health. The objective of this study was to determine if HBV is present in serum and liver of chickens. A total of 129 serum samples from broiler chickens were collected for the detection of HBV antigens and antibodies, and 193 liver samples were tested for HBV DNA sequence by PCR and for the existence of HBV antigens by immunohistochemistry. The overall prevalence of HBsAg, anti-HBs, anti-HBc was 28.68%, 53.49%, 17.05%, respectively, whereas HBeAg, anti-HBe were barely detectable. Three serum samples were found to be positive for both HBsAg and HBeAg. Further analysis of these samples with transmission electron microscopy (TEM) revealed two morphologic particles with 20 nm and 40 nm in diameter, which were similar to small spherical and Danes particles of HBV. The viral DNA sequence identified in two of the chicken livers shared 92.2% of one known HBV strain and 97.9% nucleotide sequence of another HBV strain. Our results showed the existence of HBV in chickens. This would present a significant risk to people who work with live chickens or chicken products if HBV found in chicken could be confirmed to be the same as human HBV

A new assessment model for tumor heterogeneity analysis with [18]F-FDG PET images

It has been shown that the intratumor heterogeneity can be characterized with quantitative analysis of the [18]F-FDG PET image data. The existing models employ multiple parameters for feature extraction which makes it difficult to implement in clinical settings for the quantitative characterization. This article reports an easy-to-use and differential SUV based model for quantitative assessment of the intratumor heterogeneity from 3D [18]F-FDG PET image data. An H index is defined to assess tumor heterogeneity by summing voxel-wise distribution of differential SUV from the [18]F-FDG PET image data. The summation is weighted by the distance of SUV difference among neighboring voxels from the center of the tumor and can thus yield increased values for tumors with peripheral sub-regions of high SUV that often serves as an indicator of augmented malignancy. Furthermore, the sign of H index is used to differentiate the rate of change for volume averaged SUV from its center to periphery. The new model with the H index has been compared with a widely-used model of gray level co-occurrence matrix (GLCM) for image texture characterization with phantoms of different configurations and the [18]F-FDG PET image data of 6 lung cancer patients to evaluate its effectiveness and feasibility for clinical uses. The comparison of the H index and GLCM parameters with the phantoms demonstrate that the H index can characterize the SUV heterogeneity in all of 6 2D phantoms while only 1 GLCM parameter can do for 1 and fail to differentiate for other 2D phantoms. For the 8 3D phantoms, the H index can clearly differentiate all of them while the 4 GLCM parameters provide complicated patterns in the characterization. Feasibility study with the PET image data from 6 lung cancer patients show that the H index provides an effective single-parameter metric to characterize tumor heterogeneity in terms of the local SUV variation, and it has higher correlation with tumor volume change after radiotherapy (R2 = 0.83) than the 4 GLCM parameters (R2 = 0.63, 0.73, 0.59 and 0.75 for Energy, Contrast, Local Homogeneity and Entropy respectively). The new model of the H index has the capacity to characterize the intratumor heterogeneity feature from 3D [18]F-FDG PET image data. As a single parameter with an intuitive definition, the H index offers potential for clinical applications

Drought stress had a predominant effect over heat stress on three tomato cultivars subjected to combined stress

BACKGROUND: Abiotic stresses due to environmental factors could adversely affect the growth and development of crops. Among the abiotic stresses, drought and heat stress are two critical threats to crop growth and sustainable agriculture worldwide. Considering global climate change, incidence of combined drought and heat stress is likely to increase. The aim of this study was to shed light on plant growth performance and leaf physiology of three tomatoes cultivars (‘Arvento’, ‘LA1994’ and ‘LA2093’) under control, drought, heat and combined stress. RESULTS: Shoot fresh and dry weight, leaf area and relative water content of all cultivars significantly decreased under drought and combined stress as compared to control. The net photosynthesis and starch content were significantly lower under drought and combined stress than control in the three cultivars. Stomata and pore length of the three cultivars significantly decreased under drought and combined stress as compared to control. The tomato ‘Arvento’ was more affected by heat stress than ‘LA1994’ and ‘LA2093’ due to significant decreases in shoot dry weight, chlorophyll a and carotenoid content, starch content and NPQ (non-photochemical quenching) only in ‘Arvento’ under heat treatment. By comparison, the two heat-tolerant tomatoes were more affected by drought stress compared to ‘Arvento’ as shown by small stomatal and pore area, decreased sucrose content, Φ(PSII) (quantum yield of photosystem II), ETR (electron transport rate) and q(L) (fraction of open PSII centers) in ‘LA1994’ and ‘LA2093’. The three cultivars showed similar response when subjected to the combination of drought and heat stress as shown by most physiological parameters, even though only ‘LA1994’ and ‘LA2093’ showed decreased F(v)/F(m) (maximum potential quantum efficiency of photosystem II), Φ(PSII), ETR and q(L) under combined stress. CONCLUSIONS: The cultivars differing in heat sensitivity did not show difference in the combined stress sensitivity, indicating that selection for tomatoes with combined stress tolerance might not be correlated with the single stress tolerance. In this study, drought stress had a predominant effect on tomato over heat stress, which explained why simultaneous application of heat and drought revealed similar physiological responses to the drought stress. These results will uncover the difference and linkage between the physiological response of tomatoes to drought, heat and combined stress and be important for the selection and breeding of tolerant tomato cultivars under single and combine stress

Quantitative assessment of metabolic tumor burden in molecular subtypes of primary breast cancer with FDG PET/CT

PURPOSE:We aimed to quantitatively evaluate volumetric metabolic tumor burden including metabolic tumor volume and total lesion glycolysis in different molecular subtypes of breast cancer using 18F-fluorodeoxyglucose (FDG) positron emission tomography/ computed tomography (PET/CT).METHODS:This study involved 99 female patients with pathologic diagnosis of primary breast cancer, who underwent 18F-FDG PET/CT before any therapy. Patients were divided into subtypes of luminal A, luminal B, ERBB2+, and basal-like based on the immunohistochemistry results. Metabolic tumor volume (MTV) and total lesion glycolysis (TLG) before and after correction for lean body mass were achieved and compared. Correlations between metabolic tumor burden and Ki-67 were analyzed and diagnostic performances of volumetric metabolic parameters were evaluated.RESULTS:TLG values were significantly different between each molecular subtype, while MTV values were not. Values of TLG were significantly reduced after normalizing for lean body mass in each subtype. Both of them showed correlations with Ki-67 and presented high diagnostic ability in identifying patients with basal-like breast cancer from the rest. TLGs before and after normalizing for the lean body mass had similar diagnostic performances in differentiating patients of basal-like subtype from the rest.CONCLUSION:Metabolic tumor burden could comprehensively reflect tumor metabolic differences of molecular subtypes of breast cancer, and it can serve to help differentiate patients with basal-like breast cancer

A Mechanochemical Reaction Cascade for Controlling Load-Strengthening of a Mechanochromic Polymer

We demonstrate an intermolecular reaction cascade to control the force which triggers crosslinking of a mechanochromic polymer of spirothiopyran (STP). Mechanochromism arises from rapid reversible force-sensitive isomerization of STP to a merocyanine, which reacts rapidly with activated C=C bonds. The concentration of such bonds, and hence the crosslinking rate, is controlled by force-dependent dissociation of a Diels–Alder adduct of anthracene and maleimide. Because the adduct requires ca. 1 nN higher force to dissociate at the same rate as that of STP isomerization, the cascade limits crosslinking to overstressed regions of the material, which are at the highest rate of material damage. Using comb polymers decreased the minimum concentration of mechanophores required to crosslinking by about 100-fold compared to previous examples of load-strengthening materials. The approach described has potential for controlling a broad range of reaction sequences triggered by mechanical load

Comparison of Diagnostic Performance of Three-Dimensional Positron Emission Mammography versus Whole Body Positron Emission Tomography in Breast Cancer

Objective. To compare the diagnostic performance of three-dimensional (3D) positron emission mammography (PEM) versus whole body positron emission tomography (WBPET) for breast cancer. Methods. A total of 410 women with normal breast or benign or highly suspicious malignant tumors were randomized at 1 : 1 ratio to undergo 3D-PEM followed by WBPET or WBPET followed by 3D-PEM. Lumpectomy or mastectomy was performed on eligible participants after the scanning. Results. The sensitivity and specificity of 3D-PEM were 92.8% and 54.5%, respectively. WBPET showed a sensitivity of 95.7% and specificity of 56.8%. After exclusion of the patients with lesions beyond the detecting range of the 3D-PEM instrument, 3D-PEM showed higher sensitivity than WBPET (97.0% versus 95.5%, P = 0.913), particularly for small lesions (<1 cm) (72.0% versus 60.0%, P = 0.685). Conclusions. The 3D-PEM appears more sensitive to small lesions than WBPET but may fail to detect lesions that are beyond the detecting range. This study was approved by the Ethics Committee (E2012052) at the Tianjin Medical University Cancer Institute and Hospital (Tianjin, China). The instrument positron emission mammography (PEMi) was approved by China State Food and Drug Administration under the registration number 20153331166

Comparative analysis on international construction and demolition waste management policies and laws for policy makers in China

In the current age of enhanced environmental awareness, transformation to sustainable management in the construction sector is needed. China currently produces the largest amount of construction and demolition (C&D) waste around the world, but the average recovery rate of the waste was only about 5% in 2017. In order to investigate problems in current C&D waste management in China, a cross-national comparative analysis is conducted among China and seven selected countries (Japan, South Korea, Germany, Italy, Austria, the Netherlands and the United Kingdom), to compare legal texts of national policies and laws which relate to C&D waste management and are currently being used. Through the comparison, problems in management of C&D waste in China are investigated. The problems could be concluded to: (a) inadequate guidance on recycling, (b) lack of market incentives in utilising recycled materials, (c) incomplete knowledge of stakeholders’ responsibilities, (d) lack of penalty for other stakeholders, and (e) inefficient supervision system. By understanding these problems, this paper further provides recommendations to enhance the performance of C&D waste management in China

A Mechanochemical Reaction Cascade for Controlling Load‐Strengthening of a Mechanochromic Polymer

We demonstrate an intermolecular reaction cascade to control the force which triggers crosslinking of a mechanochromic polymer of spirothiopyran (STP). Mechanochromism arises from rapid reversible force-sensitive isomerization of STP to a merocyanine, which reacts rapidly with activated C=C bonds. The concentration of such bonds, and hence the crosslinking rate, is controlled by force-dependent dissociation of a Diels–Alder adduct of anthracene and maleimide. Because the adduct requires ca. 1 nN higher force to dissociate at the same rate as that of STP isomerization, the cascade limits crosslinking to overstressed regions of the material, which are at the highest rate of material damage. Using comb polymers decreased the minimum concentration of mechanophores required to crosslinking by about 100-fold compared to previous examples of load-strengthening materials. The approach described has potential for controlling a broad range of reaction sequences triggered by mechanical load