Numerical simulation of flame acceleration and deflagration-to-detonation transition in hydrogen-air mixtures with concentration gradients

The present study aims to test the capability of our newly developed density-based solver, ExplosionFoam, for flame acceleration (FA) and deflagration-to-detonation transition (DDT) in mixtures with concentration gradients which is of important safety concern. The solver is based on the open source computational fluid dynamics (CFD) platform OpenFOAM® and uses the hydrogen-air single-step chemistry and the corresponding transport coefficients developed by the authors. Numerical simulations have been conducted for the experimental set up of Ettner et al. [7], which involves flame acceleration and DDT in both homogeneous hydrogen-air mixture as well as an inhomogeneous mixture with concentration gradients in an obstucted channel. The predictions demonstrate good quantitative agreement with the experimental measurements in flame tip position, speed and pressure profiles. Qualitatively, the numerical simulations have reproduced well the flame acceleration and DDT phenomena observed in the experiment. The results have revealed that in the computed cases, DDT is induced by the interaction of the precursor inert shock wave with the wall close to high hydrogen concentration rather than with the obstacle. Some vortex pairs appear ahead of the flame due to the interaction between the obstacles and the gas flow caused by combustion-induced expansion, but they soon disappear after the flame passes through them. Hydrogen cannot be completely consumed especially in the fuel rich region. This is of additional safety concern as the unburned hydrogen can be potentially re-ignited once more fresh air is available in an accidental scenario, resulting in subsequent explosions

A computationally efficient QRS detection algorithm for wearable ECG sensors

10.1109/IEMBS.2011.6091365Proceedings of the Annual International Conference of the IEEE Engineering in Medicine and Biology Society, EMBS5641-564

Mechanical behavior of irregular fibers part III : the flexural buckling behavior

Fiber buckling behavior is associated with fabric-evoked prickle, which affects clothing comfort and aesthetics. In this paper, the flexural buckling behavior of irregular or nonuniform fibers is studied using the finite element method (FEM). Fiber dimensional irregularities are simulated with sine waves of different magnitude, frequency, and initial phase. The critical buckling loads of the simulated fibers are then calculated from the FE model. The results indicate that increasing the level of irregularity will decrease the critical buckling load of fibers, but the effect of the frequency and initial phase of irregularity on fiber buckling behavior is complicated and is affected by fiber diameter and effective length

Negative 4-Probe Conductances of Mesoscopic Superconducting Wires

We analyze the longitudinal 4-probe conductance of mesoscopic normal and superconducting wires and predict that in the superconducting case, large negative values can arise for both the weakly disordered and localized regimes. This contrasts sharply with the behaviour of the longitudinal 4-probe conductance of normal wires, which in the localized limit is always exponentially small and positive.Comment: Latex, 3 figures available on request to [email protected] (Simon Robinson

Transparent and Conducting Boron Doped ZnO Thin Films Grown By Aerosol Assisted Chemical Vapor Deposition

ZnO based transparent conducting oxides are important as they provide an alternative to the more expensive Sn:In2O3 that currently dominates the industry. Here, we investigate B-doped ZnO thin films grown via aerosol assisted chemical vapour deposition. B:ZnO films were produced from zinc acetate and triethylborane using either tetrahydrofuran or methanol (MeOH) as the solvent. The lowest resistivity of 5.1 x 10-3 .cm along with a visible light transmittance of ~75 - 80% was achieved when using MeOH as the solvent. XRD analysis only detected the wurtzite phase of ZnO suggesting successful solid solution formation with B3+ substituting Zn2+ sites in the lattice. Refinement of the XRD patterns showed minimal distortion to the ZnO unit cell upon doping when MeOH was the solvent due to the immiscibility of the [BEt3] solution (1.0M solution in hexane) in methanol that limited the amount of B going into the films, thus preventing excessive doping

2-(3-Hydroxy-propyl)isoindoline-1,3-dione:Competition among hydrogen-bond acceptors

The title compound, C11H11NO3, has two mol-ecules in the asymmetric unit, which differ in the orientation of their side-chain OH groups, allowing them to form inter-molecular O - H⋯O hydrogen bonds to different acceptors. In one case, the acceptor is the OH group of the other mol-ecule, and in the other case it is an imide O=C group. This is the first example in the N-substituted phthalimide series in which independent mol-ecules have different types of acceptor. Mol-ecular-orbital calculations place the greatest negative charge on the OH group. © 2008 International Union of Crystallography

Parameters of the Magnetic Flux inside Coronal Holes

Parameters of magnetic flux distribution inside low-latitude coronal holes (CHs) were analyzed. A statistical study of 44 CHs based on Solar and Heliospheric Observatory (SOHO)/MDI full disk magnetograms and SOHO/EIT 284\AA images showed that the density of the net magnetic flux, $B_{{\rm net}}$, does not correlate with the associated solar wind speeds, $V_x$. Both the area and net flux of CHs correlate with the solar wind speed and the corresponding spatial Pearson correlation coefficients are 0.75 and 0.71, respectively. A possible explanation for the low correlation between $B_{{\rm net}}$ and $V_x$ is proposed. The observed non-correlation might be rooted in the structural complexity of the magnetic field. As a measure of complexity of the magnetic field, the filling factor, $f(r)$, was calculated as a function of spatial scales. In CHs, $f(r)$ was found to be nearly constant at scales above 2 Mm, which indicates a monofractal structural organization and smooth temporal evolution. The magnitude of the filling factor is 0.04 from the Hinode SOT/SP data and 0.07 from the MDI/HR data. The Hinode data show that at scales smaller than 2 Mm, the filling factor decreases rapidly, which means a mutlifractal structure and highly intermittent, burst-like energy release regime. The absence of necessary complexity in CH magnetic fields at scales above 2 Mm seems to be the most plausible reason why the net magnetic flux density does not seem to be related to the solar wind speed: the energy release dynamics, needed for solar wind acceleration, appears to occur at small scales below 1 Mm.Comment: 6 figures, approximately 23 pages. Accepted in Solar Physic

Investigation into high-frequency-vibration assisted micro-blanking of pure copper foils

The difficulties encountered during the manufacture of microparts are often associated with size effects relating to material, process and tooling. Utilizing acoustoplastic softening, achieved through a high-frequency vibration assisted micro-blanking process, was introduced to improve the surface finish in micro-blanking. A frequency of 1.0 kHz was chosen to activate the longitudinal vibration mode of the horn tip, using a piezoelectric actuator. A square hole with dimensions of 0.5 mm × 0.5 mm was made, successfully, from a commercial rolled T2 copper foil with 100 μm in thickness. It was found that the maximum blanking force could be reduced by 5% through utilizing the high-frequency vibration. Proportion of the smooth, burnished area in the cut cross-section increases with an increase of the plasticity to fracture, under the high-frequency vibration, which suggests that the vibration introduced is helpful for inhibiting evolution of the crack due to its acoustoplastic softening effect. During blanking, roughness of the burnished surface could be reduced by increasing the vibration amplitude of the punch, which played a role as surface polishing. The results obtained suggest that the high-frequency vibration can be adopted in micro-blanking in order to improve quality of the microparts