Phase Transitions in Granular Packings

We describe the contact network of granular packings by a frustrated lattice gas that contains steric frustration as essential ingredient. Two transitions are identified, a spin glass transition at the onset of Reynolds dilatancy and at lower densities a percolation transition. We describe the correlation functions that give rise to the singularities and propose some dynamical experiments

Sensitivity of Micromachined Joule-Thomson Cooler to Clogging Due to Moisture

A major issue in long-term operation of micromachined Joule-Thomson coolers is the clogging of the microchannels and/or the restriction due to the deposition of water molecules present in the working fluid. In this study, we present the performance of a microcooler operated with nitrogen gas with different moisture levels. Relatively low-purity nitrogen gas (5.0) is supplied from a gas bottle and led through a filter to control the moisture level. The filter consists of a tube-in-tube counter flow heat exchanger (CFHX) and a heat exchanger that is stabilized at a certain temperature by using a Stirling cooler. The set-point temperature determines the moisture level at the exit of the heat exchanger. It is found that the moisture level has influence on the mass-flow rate during the cool down. Once the microcooler reaches the set cold-end temperature, the main deposition area shifts into the CFHX and the moisture level at the restriction is almost independent on the inlet moisture level of the microcooler. The moisture level at the restriction increases with the increasing cold-end temperature when the cold-end temperature is lower than the saturation temperature of the water in the nitrogen gas. Higher cold-end temperature results in higher clogging rate

Vibration-free Cooler for the METIS Instrument Using Sorption Compressors

METIS is the “Mid-infrared ELT Imager and Spectrograph” for the European Extremely Large Telescope (E-ELT) that will cover the thermal/mid-infrared wavelength range from 3-14 micron. Starting from a pumped nitrogen line at 70K, it requires cryogenic cooling of detectors and optics at 40 K (1.4 W), 25 K (1.1 W), and 8 K (0.4 W). A vibration-free cooling technology for this instrument based on sorption coolers is under development at the University of Twente in collaboration with Dutch Space. We propose a sorption-based cooler with three cascaded Joule-Thomson coolers of which the sorption compressors are all heat sunk at the 70K platform. A helium-operated cooler is used to obtain the 8K level with a cooling power of 0.4 W. Here, three pre-cooling stages are used at 40K, 25K and 15K. The latter two levels are provided by a hydrogen-based cooler, whereas the 40K level is realized by a neon-based sorption cooler. Based on our space-cooler heritage, our preliminary design used sorption compressors equipped with gas-gap heat switches. These have maximum efficiency, but the gas-gap switches add significantly to the complexity of the system. Since in METIS relatively high cooling powers are required, and thus a high number of compressor cells, manufacturability is an important issue. We, therefore, developed an alternative cylindrical compressor design that uses short-pulse heating establishing a thermal wave in radial direction. This allows to omit the gas-gap heat switch. The paper discusses the adapted cell design and two METIS cooler demonstrator setups that are currently under construction

A Passive, Adaptive and Autonomous Gas Gap Heat Switch

We report on the development of a heat switch for autonomous temperature control of electronic components in a satellite. A heat switch can modulate when needed between roles of a good thermal conductor and a good thermal insulator. Electronic boxes on a satellite should be maintained within a typical optimum temperature range of 260 to 310 K. The heat sinking is usually by means of a radiator. When the operating temperature of the electronic box increases beyond 310 K, a good contact to the radiator is desired for maximum cooling. On the other hand, when the satellite is in a cold dormant state, the electronics box should be heated by the onboard batteries. In this state a weak thermal contact is desired between the electronic box and the heat sink. In the present study, we are developing a gas gap heat switch in which the sorber material is thermally anchored to the electronic box. A temperature change of the electronic box triggers the (de-)sorption of gas from the sorber material and subsequently the gas pressure in the gas gap. This paper describes the physical principles and the current status of this technology. This approach can be extended to cryogenic temperature rang

Cryogenics for an HTS degaussing system demonstrator

This paper describes the design, construction and test results of a high temperature superconducting (HTS) degaussing demonstrator system. Such a system compensates the local disturbance in the earth's magnetic field caused by the ferromagnetic hulls of ships, to prevent detection by active or passive magnetic field sensors. This is done by placing coils around the ship, creating a magnetic field opposing the effect of the earth's magnetic field. Degaussing systems for large naval vessels typically need currents of up to 1 or 2 kAturns, which gives rise to sizeable ohmic losses in conventional copper coils. These losses can be reduced if high temperature superconductors are used, since they have no electrical resistance when cooled down to temperatures below 90 K. For the demonstrator, 3 coils able to generate fields in 2 directions were realized both with HTS and copper to get a representative degaussing performance. A dedicatedly designed cooling system maintains the superconductors at a temperature of 77-85K using (subcooled) liquid nitrogen. Due to the relatively small laboratory scale that this first 1:5m long demonstrator system which was produced, the copper degaussing system is still more efficient than the HTS system because of the cooling power needed. A large fraction of this cooling power is needed to cool away parasitic heat loads, that hardly increases if the size of the system increases. Thereafter the performance of both systems was compared to evaluate on what scale HTS degaussing systems become more efficient than copper degaussing systems

Children’s hair cortisol as a biomarker of stress at school: a follow-up study

In a previous study, we examined hair cortisol concentrations (HCCs) in children when first entering elementary school (at 4 years). In this follow-up study, we examined their HCC when they entered third grade (at 6 years), where the more playful first grades proceed into a more formal learning setting. Participants were 30 6-year-old children (14 boys). Hair samples (≥5 cm) were collected 2 months after the summer holidays. Hair analysis was conducted using two 2-cm long segments, reflecting the first 2 months of school attendance in grade 3 (the scalp-near segment), and 2 months prior to the start in grade 3. Between these two sections, we left a gap of 1 cm to avoid overlap of periods (due to differences in hair growth rate). Children showed a significant increase in cortisol levels when they entered third grade. This increase was not associated with social fearfulness or academic achievement, but did show significant associations with inhibitory control: children with less inhibitory control had higher cortisol levels after entering third grade, and larger increases in cortisol than children with higher scores on inhibitory control. This suggests that the ability to inhibit or control impulsive responsivity is important for children’s stress regulation when making the transition to a more formal school environment