1,097 research outputs found
Additional measurements of the drag of surface irregularities in turbulent boundary layers
In connection with earlier measurements by K. Wieghardt the increase of the turbulent friction drag was determined for some additional types of common surface irregularities
On the turbulent friction layer for rising pressure
Among the information presented are included displacement, momentum, and kinetic energy thicknesses, shearing stress distributions across boundary layer, and surface friction coefficients. The Gruschwitz method and its modifications are examined and tested. An energy theorem for the turbulent boundary layer is introduced and discussed but does not lead to a method for the prediction of the behavior of the turbulent boundary layer because relations for the shearing stress and the surface friction are lacking
Investigations of the wall-shearing stress in turbulent boundary layers
Because of the unsatisfactory state of knowledge concerning the surface shearing stress of boundary layers with pressure gradients, the problem is re-examined. It is found that for general turbulent boundary layers in wall proximity, that is, in the laminar sublayer, in the transition zone and in the part of the completely turbulent zone near the wall, the same universal law applies as for the plate flow
Characterization of the microstructure and thermomechanical properties of invar 36 coatings deposited by HVOF and cold gas processes
The effect of impact velocity and temperature of invar particles deposited by high-velocity oxygen fuel (HVOF) and cold spray processes on the microstructure and oxidation content of invar coatings is not fully understood. Additionally, the effect of coating thickness on the coefficient of thermal expansion (CTE) of the coated material and the influence of cold working on the coating hardness are also insufficiently investigated. In the present study, invar coatings were deposited at temperatures close to and below the melting point of invar particles to maintain low CTE. It was found that particle impact temperature and velocity strongly affect pore formation and cohesiveness but slightly affect the hardness of invar coatings. Higher particle impact velocities with impact temperatures close to the invar’s melting point enhance highly the cohesiveness of HVOF-invar coatings. Furthermore, invar coatings stabilize the CTE of the coated material up to a temperature of 227 °C. An increment in the coating’s thickness of 150 µm leads to reducing the CTE of the coated material (Al) in the in-plane direction by 7.65%. Applying cold working using 200 kN compression increases the hardness of the treated coatings by 6% while machine hammer peening (MHP) has a slight effect
Оценка времени на прогнозирование технического состояния средств аппаратного контроля
Предлагается метод повышения достоверности функционирования ЭВМ АСУ в условиях воздействия мощных электромагнитных помех (МЭМП), приводятся оценки допустимого времени на прогнозирование технического состояния средств аппаратного контроля (АК) после воздействия мощных электромагнитных помех
An investigation of the influence of integration of steel heat treatment and brazing process on the microstructure and performance of vacuum-brazed cemented carbide/steel joints
Cemented carbides are commonly brazed to transformation hardening tool steels without taking a proper and adequate steel heat treatment into account. This publication shows the limits and possibilities of integrating a steel heat treatment, including a quenching process, into a vacuum brazing process. Therefore, copper-based filler metals are selected to ensure the steel component’s high and homogenous hardness and supply a high joint quality. In this context, the aimed steel hardness was chosen in the range between 400 and 440 HV1 based on industrial experiences. This specific hardness range for the steel component was set to avoid wear of machining tools in subsequent machining steps if the steel hardness is too high and to prevent wear and deformation of the tool itself in case of a steel hardness too low. When using the transformation hardening tool steel 1.2344, the obtained shear strength values did not exceed a threshold of 20 MPa which can be attributed to the required N2-quenching from brazing respectively solution annealing temperature. However, the steel components featured a hardness of 527.1 HV1 for the specimens brazed with pure copper at 1100 °C and 494.0 HV1 for those brazed with a CuGeNi filler metal at 1040 °C. This publication also shows an alternative route to manufacture long-lasting tools with a cemented carbide/steel joint by applying the difficult to wet and not well researched, but for many other reasons very suitable precipitation hardening maraging steel. Especially, the comparable low coefficient of thermal expansion (CTE) and the capability of the lath martensite to compensate large amounts of externally imposed stresses during the austenite-to-martensite transformation as well as the cooling rate independent of the hardening mechanism of the maraging steel and a pre-applied nickel coating including the corresponding diffusion processes are responsible for a sound joint with a shear strength > 300 MPa. Moreover, the subsequent tempering process at 580 °C for 3 h provides the maraging steel joining partner with a hardness of 426.6 ± 6.0 HV1
Aspects of Die Design for the Electromagnetic Sheet Metal Forming Process
Within the electromagnetic sheet metal forming process, workpiece velocities of more than 300m/s can occur, causing typical effects when forming into a die, which will be described and discussed in the present paper. These effects make numerous demands regarding the die design. In order to analyze these requirements, experimental as well as numerical investigations have been carried out. Thereby, special focus is put on the possibilities to accomplish these requirements, which are discussed in the following
Tribological Characteristics of Tungsten Carbide Reinforced Arc Sprayed Coatings using Different Carbide Grain Size Fractions
Tungsten carbide reinforced coatings play an important role in the field of surface engineering to protect stressed surfaces against wear. For thermally sprayed coatings, it is already shown that the tribological properties get mainly determined by the carbide grain size fraction. Within the scope of this study, the tribological characteristics of iron based WC-W2C reinforced arc sprayed coatings deposited using cored wires consisting of different carbide grain size fractions were examined. Microstructural characteristics of the produced coatings were scrutinized using electron microscopy and x-ray diffraction analyses. Ball-on-disk test as well as Taber Abraser and dry sand rubber wheel test were employed to analyze both the dry sliding and the abrasive wear behavior. It was shown that a reduced carbide grain size fraction as filling leads to an enhanced wear resistance against sliding. In terms of the Taber Abraser test, it is also demonstrated that a fine carbide grain size fraction results in an improved wear resistant against abrasion. As opposed to that, a poorer wear resistance was found within the dry sand rubber wheel tests. The findings show that the operating mechanisms for both abrasion tests affect the stressed surface in a different way, leading either to microcutting or microploughing
Novel Layers for Dies Used in Electromagnetic Sheet Metal Forming Processes
Due to the high forming velocities during electromagnetic sheet metal forming processes, a high impact force acts between workpiece and die. Here, the die surface sustains high damages shown by high wear and galling of the workpiece on the die surface. To enhance the die lifetime, a novel coating concept based on the PVD (physical vapour deposition) process was developed. In doing so, the hardness and the toughness of the designed layers were varied and adjusted to the demands of AlMg-sheet forming process
- …