64,646 research outputs found
The brightness temperature of the air-sea interface at microwave frequencies
Available results of observation have shown that at nadir the brightness temperature of the sea surface at 19.35 GHz increases linearly with increasing wind speed. The computational results of the modified theoretical model presented are in good agreement with the measurement results both at nadir and other angles. The model depicts that, for a fully developed sea driven by the wind with speed above 5 m/sec, the air in the transitional zone immediately above the air-sea interface is mixed with sea water droplets from bursting air bubbles. The droplet concentration has a profile tapering off to zero at a certain height. The dielectric constant of the inhomogeneous droplet profile is thus both a function of the height above the interface and the wind speed. Both the inhomogeneity effect and the possible attenuation effect of the droplet concentration have been considered
Recommended from our members
The Characteristics and Applications of Ceramic Laser Fusion and Ceramic Laser Sintering
The aim of present study is to investigate the possible application of the ceramic parts
which are fabricated with the process of Ceramic Laser Fusion or Ceramic Laser Sintering.
The experimental results reveal: (1) CLF can lead to a reduction in the porosity of the
ceramic part but also can induce micro-cracks. Therefore, this process cannot produce a part
with the required strength by a post-process of infiltration; (2) CLS is capable of fabricating a
ceramic part with high porosity. By adjusting the slurry formulation and varying the scanning
energy, the open porosity can be over 90vol% of the total porosity. After a post-process of
infiltration, the density can be increased to 95%; therefore, CLS can apply to produce a part
with high strength. Because the high open porosity leads to a good permeability, the process
of CLS is suitable for the fabrication of ceramic shell mold.Mechanical Engineerin
Robust active heave compensated winch-driven overhead crane system for load transfer in marine operation
Active heave compensation (AHC) is important for load transfer in marine operation using the overhead crane system (OCS). The control of marine OCS aims to continuously regulate the displacement of the cart and the payload sway angle, whilst at the same time, maintaining the gap between the payload and the vessel main deck at a desirable and safe distance. As the marine OHC system is to be operated in a continuously changing environment, with plenty inevitable disturbances and undesirable loads, a robust controller, i.e., active force control (AFC) is thus greatly needed to promote accuracy and robustness features into the controllability of OCS in rough working environment. This paper highlights a novel method for controlling the payload in an OCS based on the combination of both AFC and AHC. Results from the simulation study clearly indicate that the performance of OCS can be greatly improved by the proposed robust AFC controller, as compared with the classical PID controller scheme
Recommended from our members
Prospect of Making Ceramic Shell Mold by Ceramic Laser Fusion
Manufacturing prototypical castings by conventional investment casting not only takes
several weeks, but also is prohibitively expensive. Z Corporation in USA, EOS GmbH and
IPT in Germany employ the techniques of 3DP and SLS respectively to make directly ceramic
shell molds for metal castings. Although those techniques dramatically reduce time
expenditure and production cost, each layer cannot be thinner than 50 µm because of using
powder to pave layers. The dimensional accuracy and roughness of the castings still cannot
meet the specification of precision casting. Therefore, in this paper the ceramic laser fusion
(CLF) was used to pave layers. Each layer can be thinner than 25 µm, so that the step effect
can be diminished and the workpiece surface can be smoother; drying time will be shortened
dramatically. Moreover, the inherent solid-state support formed by green portion has the
capability of preventing upward and downward deformation of the scanned cross sections. In
order to make shell mold which meets the roughness requirement (Rq=3.048µm) of the
precision casting, following issues have to be further studied: (1) design a proper ceramic
shell mold structure, (2) design a paving chamber for paving a complete green layer which
can be easily collapsed, (3) cut down drying time, (4) optimize laser scanning process
parameters with the smallest distortion, (5) eliminate sunken area, (6) reduce layer thickness
to less than13µm, (7) control power to guarantee the energy uniformly absorbed by workpiece,
and (8) develop a method which can directly clean green portion in cavity from gate.Mechanical Engineerin
- …