Addressing the need for standardization of test methods for self-healing concrete: an inter-laboratory study on concrete with macrocapsules.

Development and commercialization of self-healing concrete is hampered due to a lack of standardized test methods. Six inter-laboratory testing programs are being executed by the EU COST action SARCOS, each focusing on test methods for a specific self-healing technique. This paper reports on the comparison of tests for mortar and concrete specimens with polyurethane encapsulated in glass macrocapsules. First, the pre-cracking method was analysed: mortar specimens were cracked in a three-point bending test followed by an active crack width control technique to restrain the crack width up to a predefined value, while the concrete specimens were cracked in a three-point bending setup with a displacement-controlled loading system. Microscopic measurements showed that with the application of the active control technique almost all crack widths were within a narrow predefined range. Conversely, for the concrete specimens the variation on the crack width was higher. After pre-cracking, the self-healing effect was characterized via durability tests: the mortar specimens were tested in a water permeability test and the spread of the healing agent on the crack surfaces was determined, while the concrete specimens were subjected to two capillary water absorption tests, executed with a different type of waterproofing applied on the zone around the crack. The quality of the waterproofing was found to be important, as different results were obtained in each absorption test. For the permeability test, 4 out of 6 labs obtained a comparable flow rate for the reference specimens, yet all 6 labs obtained comparable sealing efficiencies, highlighting the potential for further standardization

The simulation of transport processes in cementitious materials with embedded healing systems

A new model for simulating the transport of healing agents in self-healing (SH) cementitious materials is presented. The model is applicable to autonomic SH material systems in which embedded channels, or vascular networks, are used to supply healing agents to damaged zones. The essential numerical components of the model are a crack flow model, based on the Navier-Stokes equations, which is coupled to the mass balance equation for simulating unsaturated matrix flow. The driving forces for the crack flow are the capillary meniscus force and the force derived from an external (or internal) pressure applied to the liquid healing agent. The crack flow model component applies to non-uniform cracks and allows for the dynamic variation of the meniscus contact angle, as well as accounting for inertial terms. Particular attention is paid to the effects of curing on the flow characteristics. In this regard, a kinetic reaction model is presented for simulating the curing of the healing agent and a set of relationships established for representing the variation of rheological properties with the degree of cure. Data obtained in a linked experimental programme of work is employed to justify the choice and form of the constitutive relationships, as well as to calibrate the model’s evolution functions. Finally, a series of validation examples are presented that include the analysis of a series of concrete beam specimens with an embedded vascular network. These examples demonstrate the ability of the model to capture the transport behaviour of this type of SH cementitious material system

Acetaminophen (Paracetamol) Induces Hypothermia During Acute Cold Stress.

BACKGROUND Acetaminophen is an over-the-counter drug used to treat pain and fever, but it has also been shown to reduce core temperature (T c) in the absence of fever. However, this side effect is not well examined in humans, and it is unknown if the hypothermic response to acetaminophen is exacerbated with cold exposure. OBJECTIVE To address this question, we mapped the thermoregulatory responses to acetaminophen and placebo administration during exposure to acute cold (10 °C) and thermal neutrality (25 °C). METHODS Nine healthy Caucasian males (aged 20-24 years) participated in the experiment. In a double-blind, randomised, repeated measures design, participants were passively exposed to a thermo-neutral or cold environment for 120 min, with administration of 20 mg/kg lean body mass acetaminophen or a placebo 5 min prior to exposure. T c, skin temperature (T sk), heart rate, and thermal sensation were measured every 10 min, and mean arterial pressure was recorded every 30 min. Data were analysed using linear mixed effects models. Differences in thermal sensation were analysed using a cumulative link mixed model. RESULTS Acetaminophen had no effect on T c in a thermo-neutral environment, but significantly reduced T c during cold exposure, compared with a placebo. T c was lower in the acetaminophen compared with the placebo condition at each 10-min interval from 80 to 120 min into the trial (all p  0.05). CONCLUSION This preliminary trial suggests that acetaminophen-induced hypothermia is exacerbated during cold stress. Larger scale trials seem warranted to determine if acetaminophen administration is associated with an increased risk of accidental hypothermia, particularly in vulnerable populations such as frail elderly individuals

Experimental techniques used to verify healing

There are many techniques to study materials. In this chapter the focus o

Tunable chitosan-alginate capsules for a controlled release of crystallisation inhibitors in mortars

Plasters and renders used in historic monuments are vulnerable to degradation caused by salt weathering. Crystallisation inhibitors (molecules/ions that alter salt crystallisation) mixed into mortars have shown promising results in mitigating salt damage by inhibiting salt crystallisation, promoting salt transport to the evaporating surface, and modifying crystal habit. However, past research suggests that inhibitors easily leach out from mortars, meaning their long-term positive effect is lost. Encapsulation of an inhibitor within a mortar is a potential solution to minimise leaching. Herein, capsules composed of a polyelectrolyte complex of calcium alginate coated in chitosan are investigated for the controlled diffusive release of sodium ferrocyanide, a known NaCl crystallisation inhibitor. Capsules with varying chitosan-calcium alginate ratios are prepared using the extrusion dripping technique. The release of the inhibitor from capsules in solutions of various pH values ranging from 7–13 is investigated. Results show that increasing the capsule’s chitosan to calcium alginate ratio reduces the inhibitor release for all studied solution pH values compared to pure calcium-alginate capsules. Therefore, a controlled inhibitor release can be obtained by tuning the chitosan-alginate ratio. In future, additional tests will be performed to find suitable capsule compositions for optimising their performance when mixed in mortars

Experimental techniques used to verify healing

There are many techniques to study materials. In this chapter the focus of experimental techniques to verify crack sealing (recovery against environmental actions) or crack healing (recovery against mechanical actions) has been limited to techniques that have been used and reported in self-sealing and self-healing research. To get a look and feel of the topic the chapter starts with a section on techniques which can be used to examine crack healing such as microscopy, X-ray diffraction and Raman spectroscopy. Next, the attention shifts from observing that something has been repaired to how well the repair has been. Following the definitions set out in chapter one, a differentiatiion has been made between techniques to verify recovery against environmental or mechanical actions. For recovery against environmental actions it turns out that permeability tests are often applied, while for recovery against mechanical actions the regain in strength by mechanical testing is the preferred choice

Recovery against mechanical actions

info:eu-repo/semantics/publishe