SSME turbopump bearing analytical study

Three shuttle pump bearings operating under severe overspeed and shut-down conditions are evaluated. The specific parameters investigated include outer race stresses, cage stresses, cage-race drag, bearing heating, and crush loading. A quasi-dynamic version of the BASDAP computer code was utilized which involved the calculation of ball-race forces (inner and outer), contact pressures, contact dimensions, and contact angles as a function of (1) axial load, (2) radial load, and (3) centrifugal load on the bearing. Generally, radial loads on the order of 13,300 N (3000 pounds) per bearing or 26,700 N (6000 pounds) per bearing pair, could be expected to cause severe problems to any of the bearings with a 17,800 N (4000 pounds) axial load. Further, when possible temperature excursions are considered, even a load of 8900 N (2000 pounds) may be excessive. However, high momentary radial loads with a 3800 N (850 pounds) axial load would not be anticipated to cause catastrophic failure of the fuel pump bearing

High pressure oxygen turbopump bearing cage stability analyses

The low service life of the high pressure oxygen turbopump (HPOTP) bearings used in the space shuttle main engine was examined by use of the Battelle "BASDAP' bearing computer stability model. The dynamic instability of the bearing cage resulted in excessive wear and eventual failure of the unit. By maintaining a cage/race clearance of no more than 0.25 millimeters (0.010 inches), ball/pocket clearance of no less than 0.54 millimeters (0.025 inches), dynamic balancing of the cages, and maintaining adequate lubricant films between the balls and races, cage instability and subsequent bearing degradation can be reduced

Cage stability analysis for SSME HPOTP bearings

A numerical model of cage motion (CAGEDYN) was used to analyze the stability of bearing cages in the Space Shuttle main engine (SSME) high pressure oxygen turbopump (HPOTP). The stability of existing bearing geometries, as well as perturbations of these geometries, was analyzed for various operating conditions. Results of the analyses show that some combinations of operating parameters, exacerbated by the sparse lubrication that exist in the HPOTP bearings, can cause unstable cage oscillations. Frequencies of cage oscillations were predicted by the CAGEDYN numerical model by Fourier analysis of predicted cage motions. Under conditions that cause unstable cage motion, high frequency oscillations were predicted that could cause premature cage failures

We rode alone, of course a collection of short stories

As a high school English teacher, I often ask my students to define abstract concepts. What is happiness? What is sadness? What is justice? What is injustice? My students often groan at such questions, as they do not know where to begin with such broad ideas. That is the point, however, as my hope is that they at least attempt to explore each broad idea and consider various facets. The funny thing is, some of the activities I often subject my students to are activities I would never have wished to do as a student. I personally have no idea where to begin with some of the aforementioned concepts listed above. Stranger however, is the fact that I have no idea where to begin, if someone asked me to define loneliness. Perhaps that is not entirely true. I mean, I, as well as anyone, can start off by saying that loneliness is the state of being alone, where there is no one else around a particular individual. Where, however, do I go from there? Do I suggest that loneliness is the feeling people feel when they realize that they have not had a substantial conversation with anyone during the day, after coming home from work to an empty apartment? Is loneliness the feeling they feel when they go on a trip by themselves, and after the third or twelfth cocktail, they wish there was someone sitting next to them? Is loneliness the feeling they feel when they find no way out of their loneliness, and the thought of even a longer stretch of loneliness is flat-out demoralizing? iv I am not sure how to answer those questions as Ryan Merriman, but, through this collection of short stories, I at least attempted to explore those questions through the eyes of a principal, unemployed son, coaster enthusiast, substitute teacher, bar regular, isolated officer worker, beer connoisseur, and priest. I hope they explored this topic to the best of their abilities, as they are experts on this topic. Somehow, someway, they are alone in this world

Evaluation of feasibility of measuring EHD film thickness associated with cryogenic fluids

The feasibility of measuring elastohydrodynamic (EHD) films as formed with a cryogenic (LN2) fluid is evaluated. Modifications were made to an existing twin disk EHD apparatus to allow for disk lubrication with liquid nitrogen. This disk apparatus is equipped with an X-ray system for measuring the thickness of any lubricant film that is formed between the disks. Several film thickness experiments were conducted with the apparatus which indicate that good lubrication films are filmed with LN2. In addition to the film thickness studies, failure analyses of three bearings were conducted. The HPOTP turbine end bearings had experienced axial loads of 36,000 to 44,000 N (8,000 to 10,000 lb). High continuous radial loads were also experienced, which were most likely caused by thermal growth of the inner race. The resulting high internal loads caused race spalling and ball wear to occur

DNA double strand breaks but not interstrand crosslinks prevent progress through meiosis in fully grown mouse oocytes

There is some interest in how mammalian oocytes respond to different types of DNA damage because of the increasing expectation of fertility preservation in women undergoing chemotherapy. Double strand breaks (DSBs) induced by ionizing radiation and agents such as neocarzinostatin (NCS), and interstrand crosslinks (ICLs) induced by alkylating agents such as mitomycin C (MMC), are toxic DNA lesions that need to be repaired for cell survival. Here we examined the effects of NCS and MMC treatment on oocytes collected from antral follicles in mice, because potentially such oocytes are readily collected from ovaries and do not need to be in vitro grown to achieve meiotic competency. We found that oocytes were sensitive to NCS, such that this ionizing radiation mimetic blocked meiosis I and caused fragmented DNA. In contrast, MMC had no impact on the completion of either meiosis I or II, even at extremely high doses. However, oocytes treated with MMC did show ?-H2AX foci and following their in vitro maturation and parthenogenetic activation the development of the subsequent embryos was severely compromised. Addition of MMC to 1-cell embryos caused a similarly poor level of development, demonstrating oocytes have eventual sensitivity to this ICL-inducing agent but this does not occur during their meiotic division. In oocytes, the association of Fanconi Anemia protein, FANCD2, with sites of ICL lesions was not apparent until entry into the embryonic cell cycle. In conclusion, meiotic maturation of oocytes is sensitive to DSBs but not ICLs. The ability of oocytes to tolerate severe ICL damage and yet complete meiosis, means that this type of DNA lesion goes unrepaired in oocytes but impacts on subsequent embryo quality

Investigation of instability, dynamic forces, and effect of dynamic loading on strength of cages for the bearings in the high pressure oxygen turbopumps for the space shuttle main engine

Experiments were performed to determine the effect of cyclic loading on bearing cage strength. A long term working tensile load of approximately 1300 N (300 lbs) was found to be the likely maximum. Higher loads caused a decrease in cage tensile strength after the 125,000 cycle testing period. Poisson's ratio in compression was found to be highly dependent upon the direction of the fiberglass plies. At room temperature the value was 0.15 with the plies and 0.68 across the plies. At -196 C (-321 F), the value with the plies was 0.20. The results of the analyses conducted have again demonstrated the critical need for improved lubrication in the high pressure oxygen turbopump bearings. Lubricant films with low shear strength and low friction coefficients promote cage stability and decrease ball/cage forces during marginal operating conditions. The analysis of the effect of combined bearing loads on ball/cage loads has identified a radial load of 3600 N (800 lbs) as the maximum for the current clearance of the balls and cage pockets. Liquid oxygen impinging on the cage in the direction of rotation was found to enhance cage stability

Measurements of elastohydrodynamic film thickness, wear and tempering behavior of high pressure oxygen turbopump bearings

The reusable design of the Space Shuttle requires a target life of 7.5 hours for the turbopumps of the Space Shuttle main engine (SSME). This large increase from the few hundred seconds required in single-use rockets has caused various problems with the bearings of the turbopumps. The berings of the high pressure oxygen turbopump (HPOTP) were of particular concern because of wear, spalling, and cage failures at service time well below the required 7.5 hours. Lubrication and wear data were developed for the bearings. Since the HPOTP bearings operate in liquid oxygen, conventional liquid lubricants cannot be applied. Therefore, solid lubricant coatings and lubricant transfer from the polytetrafluorethylene (FTFE) cage were the primary lubrication approaches for the bearings. Measurements were made using liquid nitrogen in a rolling disk machine to determine whether usable elastohydrodynamic films could be generated to assist in the bearing lubrication

Evaluation of outer race tilt and lubrication on ball wear and SSME bearing life reductions

Several aspects of the SSME bearing operation were evaluated. The possibility of elastohydrodynamics (EHD) lubrication with a cryogenic fluid was analyzed. Films as thick as .61 microns were predicted with one theory which may be thick enough to provide hydrodynamic support. The film formation, however, is heavily dependent on good surface finish and a low bulk bearing temperature. Bearing dynamics to determine if the radial stiffness of a bearing which are dependent on bearing misalignment were analyzed. Four ball tests were conducted at several environmental conditions from an LN2 bath to 426 C in air. Surface coatings and ball materials are evaluated. Severe wear and high friction are measured for all ball materials except when the balls have surface lubricant coatings

A bioinformatics workflow for detecting signatures of selection in genomic data

The detection of “signatures of selection” is now possible on a genome-wide scale in many plant and animal species, and can be performed in a population-specific manner due to the wealth of per-population genome-wide genotype data that is available. With genomic regions that exhibit evidence of having been under selection shown to also be enriched for genes associated with biologically important traits, detection of evidence of selective pressure is emerging as an additional approach for identifying novel gene-trait associations. While high-density genotype data is now relatively easy to obtain, for many researchers it is not immediately obvious how to go about identifying signatures of selection in these data sets. Here we describe a basic workflow, constructed from open source tools, for detecting and examining evidence of selection in genomic data. Code to install and implement the pipeline components, and instructions to run a basic analysis using the workflow described here, can be downloaded from our public GitHub repository: http://www.github.com/smilefreak/selectionTools