3,566 research outputs found
Influence of residual pressure and ion implantation on the structure, elemental composition, and properties of (TiZrAlYNb)N nitrides
The nitrides of highentropy alloys, (TiZrAlYNb)N, fabricated by cathodic vacuum arc evaporation are studied with electron microscopy, atomic force microscopy, laser scanning microscopy; energydispersive Xray analysis, Xray phase analysis, timeofflight secondaryion mass spectrometry; and hardness measurements. It is found that the deposition parameters influence the structure, surface morphology, element distribution, and mechanical properties. The structural–phase state of the coatings before and after the ion implantation of heavy negative gold ions Au– are compared.
DOI: 10
A study of the etapipi channel produced in central pp interactions at 450 GeV/c
The reaction pp -> pf (eta pi pi) ps has been studied at 450 GeV/c. There is
clear evidence for an a2(1320)pi decay mode of the eta2(1645) and eta2(1870).
In addition, there is evidence for an a0(980)pi$ decay mode of both resonances
and an f2(1270)eta decay mode of the eta2(1870). No evidence is found for a JPC
= 2++ a2(1320)pi wave.Comment: 15 pages, Latex, 4 Figures Branching ratio a2pi /f2 eta correcte
Structural features and physico-mechanical properties of AlN-TiB2-TiSi2 amorphous-like coatings
The coating of the AlN–TiB2–TiSi2 system has been produced by the magnetron sputtering of
a target. At the hightemperature (900 and 1300°C) actions the coating crystallization to form crystallites
of sizes 11–25 nm has been observed. It has been defined that the amorphouslike structure is promising
for the use of these coatings as diffusion barriers both as the independent elements and a contacting layer
in multilayer wearresistant coatings. It has been shown that the use of the resultant composite as an effec
tive protective coating for cutting tools will make it possible to increase the tools wear resistance by more
than 30% at the temperature up to 1300°C in the cutting zone
Structural features and physico-mechanical properties of AlN-TiB2-TiSi2 amorphous-like coatings
The coating of the AlN–TiB2–TiSi2 system has been produced by the magnetron sputtering of
a target. At the hightemperature (900 and 1300°C) actions the coating crystallization to form crystallites
of sizes 11–25 nm has been observed. It has been defined that the amorphouslike structure is promising
for the use of these coatings as diffusion barriers both as the independent elements and a contacting layer
in multilayer wearresistant coatings. It has been shown that the use of the resultant composite as an effec
tive protective coating for cutting tools will make it possible to increase the tools wear resistance by more
than 30% at the temperature up to 1300°C in the cutting zone
Towards Prospective Life Cycle Assessment: How to Identify Key Parameters Inducing Most Uncertainties in the Future? Application to Photovoltaic Systems Installed in Spain
The final publication is available at Springer via http://dx.doi.org/10.1007/978-3-319-09150-1_51International audienceProspective Life Cycle Assessment (LCA) is a relevant approach to assess the environmental performance of future energy pathways. Amongst different types of prospective scenarios, cornerstone scenarios meant for complex systems and long-term approaches, are of interest to assess such performance. They rely on different types of long-term projections, such as projections of technological evolutions and of energy resources. In most studies, scenarios are defined with single values for each parameter, and environmental impacts are assessed in a deterministic way. Inherent uncertainties related to these prospective assumptions are not considered and prospective LCA uncertainties are thus not addressed. In this paper we describe a methodology to account for these uncertainties and to identify the parameters inducing most of the uncertainties in the prospective LCA results. We apply this approach to prospective LCAs of photovoltaic-based electricity generation systems
A search for charmonium states produced in central pp interactions at 450 GeV/c
A search for centrally produced charmonium states has been presented. There
is no significant evidence for any charmonium production. An upper limit of 2
nb is found for the cross section of chic production using the decay chic(1P)->
J/psi gamma.Comment: 10 pages, Latex, 4 Figure
A study of the f0(1370), f0(1500), f0(2000) and f2(1950) observed in the centrally produced 4pi final states
The production and decay properties of the f0(1370), f0(1500), f0(2000) and
f2(1950) have been studied in central pp interactions at 450 GeV/c. The dPT,
phi and |t| distributions of these resonances are presented. For the J = 0
states, the f0(1370) and f0(2000) have similar dPT and phi dependences. These
are different to the dPT and phi dependences of the f0(980), f0(1500) and
f0(1710). For the J = 2 states the f2(1950) has different dependences to the
f2(1270) and f2'(1520). This shows that the dPT and phi dependences are not
just J phenomena.Comment: 14 pages, Latex, 4 Figure
A study of the centrally produced pi0pi0pi0 channel in pp interactions at 450 GeV/c
The reaction pp -> pf (pi0pi0pi0) ps has been studied at 450 GeV/c. The
pi0pi0pi0 effective mass spectrum shows clear eta(547) and pi2(1670) signals.
Branching ratios for the eta(547) and pi_2(1670) are given as well as upper
limits for the decays of the omega(782), a1(1260) and a2(1320) into 3pi0.Comment: 10 pages, Latex, 4 Figure
- …