A computerized Langmuir probe system

For low pressure plasmas it is important to record entire single or double Langmuir probe characteristics accurately. For plasmas with a depleted high energy tail, the accuracy of the recorded ion current plays a critical role in determining the electron temperature. Even for high density Maxwellian distributions, it is necessary to accurately model the ion current to obtain the correct electron density. Since the electron and ion current saturation values are, at best, orders of magnitude apart, a single current sensing resistor cannot provide the required resolution to accurately record these values. We present an automated, personal computer based data acquisition system for the determination of fundamental plasma properties in low pressure plasmas. The system is designed for single and double Langmuir probes, whose characteristics can be recorded over a bias voltage range of ±70 V with 12 bit resolution. The current flowing through the probes can be recorded within the range of 5 nA–100 mA. The use of a transimpedance amplifier for current sensing eliminates the requirement for traditional current sensing resistors and hence the need to correct the raw data. The large current recording range is realized through the use of a real time gain switching system in the negative feedback loop of the transimpedance amplifier

The influence of an external magnetic field on the dynamic stress of an elastic conducting one-sided layer with a longitudinal shear crack

We study the interaction of a magnetoelastic shear wave with a curvilinear tunnel crack in an ideally conducting diamagnetic (resp. paramagnetic) one-sided (resp. two-sided) layer in the presence of an external static magnetic field. The bases of the one-sided layer are free of mechanical load, and the rim of the face is clamped or free. The corresponding linearized boundary-value problem of magnetoelasticity is reduced to a singular integrodifferential equation with subsequent implementation on a computer. We give numerical results that characterize the influence of the size of the preliminary magnetic field, the frequencies of the load, the curvature, and the orientation of the crack on the stress intensity factor. When you are citing the document, use the following link http://essuir.sumdu.edu.ua/handle/123456789/2163

Absorption spectrum in the wings of the potassium second resonance doublet broadened by helium

We have measured the reduced absorption coefficients occurring in the wings of the potassium 4S-5P doublet lines at 404.414 nm and at 404.720 nm broadened by helium gas at pressures of several hundred Torr. At the experimental temperature of 900 K, we have detected a shoulder-like broadening feature on the blue wing of the doublet which is relatively flat between 401.8 nm and 402.8 nm and which drops off rapidly for shorter wavelengths, corresponding to absorption from the X doublet Sigma+ state to the C doublet Sigma+ state of the K-He quasimolecule. The accurate measurements of the line profiles in the present work will sharply constrain future calculations of potential energy surfaces and transition dipole moments correlating to the asymptotes He-K(5p), He-K(5s), and He-K(3d).Comment: 2 figure

Millikelvin magnetic relaxation measurements of alpha-Fe2O3 antiferromagnetic particles

In this paper we report magnetic relaxation data for antiferromagnetic alpha-Fe2O3 particles of 5 nm mean diameter in the temperature range 0.1 K to 25 K. The average spin value of these particles S=124 and the uniaxial anisotropy constant D=1.6x10^-2 K have been estimated from the experimental values of the blocking temperature and anisotropy field. The observed plateau in the magnetic viscosity from 3 K down to 100 mK agrees with the occurrence of spin tunneling from the ground state Sz = S. However, the scaling M vs Tln(nu t) is broken below 5 K, suggesting the occurrence of tunneling from excited states below this temperature.Comment: 4 pages (two columns), 4 figure

The Yellow Excitonic Series of Cu2O Revisited by Lyman Spectroscopy

We report on the observation of the yellow exciton Lyman series up to the fourth term in Cu2O by time-resolved mid-infrared spectroscopy. The dependence of the oscillator strength on the principal quantum number n can be well reproduced using the hydrogenic model including an AC dielectric constant, and precise information on the electronic structure of the 1s exciton state can be obtained. A Bohr radius a_{1s}=7.9 A and a 1s-2p transition dipole moment \mu_{1s-2p}= 4.2 eA were found

Simulations of energetic beam deposition: from picoseconds to seconds

We present a new method for simulating crystal growth by energetic beam deposition. The method combines a Kinetic Monte-Carlo simulation for the thermal surface diffusion with a small scale molecular dynamics simulation of every single deposition event. We have implemented the method using the effective medium theory as a model potential for the atomic interactions, and present simulations for Ag/Ag(111) and Pt/Pt(111) for incoming energies up to 35 eV. The method is capable of following the growth of several monolayers at realistic growth rates of 1 monolayer per second, correctly accounting for both energy-induced atomic mobility and thermal surface diffusion. We find that the energy influences island and step densities and can induce layer-by-layer growth. We find an optimal energy for layer-by-layer growth (25 eV for Ag), which correlates with where the net impact-induced downward interlayer transport is at a maximum. A high step density is needed for energy induced layer-by-layer growth, hence the effect dies away at increased temperatures, where thermal surface diffusion reduces the step density. As part of the development of the method, we present molecular dynamics simulations of single atom-surface collisions on flat parts of the surface and near straight steps, we identify microscopic mechanisms by which the energy influences the growth, and we discuss the nature of the energy-induced atomic mobility

Fabrication of Metal and Alloy Components by Additive Manufacturing: Examples of 3D Materials Science

ObjectiveThis paper provides a brief review of relatively new additive manufacturing technologies for the fabrication of unusual and complex metal and alloy products by laser and electron beam melting. A number of process features and product microstructures are illustrated utilizing 3D optical and transmission electron microscope image compositions representing examples of 3D materials science.MethodsProcessing methods involving electron beam melting (EBM) and a process referred to as direct metal laser sintering (DMLS), often called selective laser melting (SLM) are described along with the use of light (optical) microscopy (OM), transmission electron microscopy (TEM), and X-ray diffraction (XRD) to elucidate microstructural phenomena.ResultsExamples of EBM and SLM studies are presented in 3D image compositions. These include EBM of Ti-6Al-4V, Cu, Co-base superalloy and Inconel 625; and SLM of 17-4 PH stainless steel, Inconel 718 and Inconel 625.Conclusions3D image compositions constituting 3D materials science provide effective visualization for directional solidification-related phenomena associated with the EBM and SLM fabrication of a range of metals and alloys, especially microstructures and microstructural architectures