1,827 research outputs found
Numerical simulation of heat transfer to separation tio(2)/water nanofluids flow in an asymmetric abrupt expansion
Flow separation and reattachment of 0.2% TiO2 nanofluid in an asymmetric abrupt expansion is studied in this paper. Such flows occur in various engineering and heat transfer applications. Computational fluid dynamics package (FLUENT) is used to investigate turbulent nanofluid flow in the horizontal double-tube heat exchanger. The meshing of this model consists of 43383 nodes and 74891 elements. Only a quarter of the annular pipe is developed and simulated as it has symmetrical geometry. Standard k-epsilon second order implicit, pressure based-solver equation is applied. Reynolds numbers between 17050 and 44545, step height ratio of 1 and 1.82 and constant heat flux of 49050 W/m2 was utilized in the simulation. Water was used as a working fluid to benchmark the study of the heat transfer enhancement in this case. Numerical simulation results show that the increase in the Reynolds number increases the heat transfer coefficient and Nusselt number of the flowing fluid. Moreover, the surface temperature will drop to its lowest value after the expansion and then gradually increase along the pipe. Finally, the chaotic movement and higher thermal conductivity of the TiO2 nanoparticles have contributed to the overall heat transfer enhancement of the nanofluid compare to the water
Experimental study on a feasibility of using electromagnetic wave cylindrical cavity sensor to monitor the percentage of water fraction in a two phase system
This study proposed a microwave sensor system to monitor single and two phase flow systems. The microwave sensing technology in this study utilises the resonant frequencies that occur in a cylindrical cavity and monitor the changes in the permittivity of the measured phases to differentiate between the volume fractions of air, water and oil. The sensor system used two port configuration S21 (acted as transmitter and receiver) to detect the fluids inside the pipe. In principle, the strong polarity of water molecules results in higher permittivity in comparison to other materials. A tiny change of water fraction will cause a significant frequency shift. Electromagnetic waves in the range of 5 GHz to 5.7 GHz have been used to analyse a two phase air-water and oil-water stratified flow in a pipeline. The results demonstrated the potential of a microwave sensing technique to be used for the two phase systems monitoring. A significant shift in the frequency and change in the amplitude clearly shows the percentage fraction change of water in the pipe. The temperature study of water also demonstrated the independence of microwave analysis technique to the temperature change. This is accounted to overlapping modes negating the affect. Statistical analysis of the amplitude data for two phase systems shows a linear relationship of the change in water percentage to the amplitude. The electromagnetic wave cavity sensor successfully detected the change in the water fraction inside the pipe between 0-100%. The results show that the technique can be developed further to reduce the anomalies in the existing microwave sensor
Increase in Convective Heat Transfer over A Backward-Facing Step Immersed in A Water-Based Tio2 Nanofluid
Investigation of flow separation and reattachment of 0.2% water-based TiO2 nanofluid in an annular suddenly expanding pipe is presented in this paper. Such flows occur in various engineering and heat transfer applications. A computational fluid dynamics package (FLUENT) is used to study turbulent nanofluid flow in this research. Only a quarter of an annular pipe was investigated and simulated because of its symmetrical geometry. Standard k–ε second-order implicit, pressure based-solver equations are applied. Reynolds numbers between 17,050 and 44,545, step height ratio of 1.82, and a constant heat flux of 49,050 W/m2 were utilized in simulation. The numerical simulation results show that increase in the Reynolds number leads to an increase of the heat transfer coefficient and of the Nusselt number. Moreover, the surface temperature dropped to its lowest value after the expansion and then gradually increased along the pipe. Finally, the chaotic movement and high thermal conductivity of the TiO2 nanoparticles have contributed to the overall heat transfer enhancement of the nanofluid
Numerical Investigation on Using an Electromagnetic Wave Sensor to Detect Water Hardness in Water Cooling System Industry
Numerical study of using novel electromagnetic wave technique to detect water hardness concentration has been presented in this paper. Simulation is powerful and efficient engineering methods which allows for a quick and accurate prediction of various engineering problems. The RF module is used in this research to predict and design electromagnetic wave propagation and resonance effects of a guided wave to detect water hardness concentration in term of frequency domain, eigenfrequency and mode analysis. A cylindrical cavity resonator is simulated and designed in the electric field of fundamental mode (TM010). With the finite volume method, the three-dimensional governing equations were discretized. Boundary conditions for the simulation were the cavity materials as aluminum, two ports which include transmitting and receiving port, and assumption of vacuum inside the cavity. The designed model was success to simulate a fundamental mode and extract S21 transmission signal within 2.1 GHz – 2.8 GHz regions. The signal spectrum under effects of port selection technique and dielectric properties of different water concentration were studied. It is observed that the linear reduction of magnitude in frequency domain when concentration increase. The numerical results were validated closely by the experimental available data. Hence, conclusion of the available COMSOL simulation package is capable of providing acceptable data for microwave research
Retardation of heat exchanger surfaces mineral fouling by water-based diethylenetriamine pentaacetate-treated CNT nanofluids
Mineral scale deposition on heat exchanging surfaces increases the thermal resistance and reduces the operating service life. The effect is usually intensified at higher temperatures due to the inverse temperature solubility characteristics of some minerals in the cooling water. Scale formation build up when dissolved salt crystallize from solution onto the heated surface, forming an adherent deposit. It is very important for heat transfer applications to cope with the fouling problems in industry. In this present study, a set of fouling experiments was conducted to evaluate the mitigation of calcium carbonate scaling by applying DTPA-treated MWCNT-based water nanofluids on heat exchanger surfaces. Investigation of additive DTPA-treated MWCNT-based water nanofluids (benign to the environment) on fouling rate of deposition was performed. 300 mg L−1 of artificially-hardened calcium carbonate solution was prepared as a fouling solution for deposit analysis. Assessment of the deposition of calcium carbonate on the heat exchanger surface with respect to the inhibition of crystal growth was conducted by Scanning Electron Microscope (SEM). The results showed that the formation of calcium carbonate crystals can be retarded significantly by adding MWCNT-DTPA additives as inhibition in the solution
Quantifying the burden of rhodesiense sleeping sickness in Urambo district, Tanzania
Sleeping sickness (human African trypanosomiasis - HAT) is a disease transmitted by tsetse flies and is always fatal if left untreated. The disease occurs in foci affecting poor communities with limited access to health service provision and as such the disease is often left undiagnosed, mistaken for more common afflictions. Even if diagnosed, sleeping sickness is costly to treat, both for health services and patients and their families in terms of costs of diagnosis, transport, hospital care, and the prolonged period of convalescence. Here we estimate the health burden of the acute form T. b. rhodesiense sleeping sickness in Urambo District, Tanzania in terms of Disability Adjusted Life Years (DALYs), the yardstick commonly used by policy makers to prioritize disease management practices, representing a year of healthy life lost to disease. In this single district, the burden of the disease over one year was estimated at 979 DALYs and the estimated monetary costs to health services for the 143 treated patients at US 3,673 for direct medical costs and US$ 9,781 for indirect non-medical costs. Sleeping sickness thus places a considerable burden on the affected rural communities and health services
A comparison of intrauterine haemopoietic cell transplantation and lentiviral gene transfer for the correction of severe β-thalassaemia in a HbbTh3/+ murine model
Major haemoglobinopathies place tremendous strain on global resources. Intrauterine haemopoietic cell (IUHCT) and gene (IUGT) therapies can potentially reduce perinatal morbidities with greater efficacy than postnatal therapy alone. We performed both procedures in the thalassaemic HbbTh3/+ murine model. Intraperitoneal delivery of coisogenic cells at E13-14 produced dose-dependent chimerism. High-dose adult bone marrow (BM) cells maintained 0.2-3.1% chimerism over ~24 weeks and treated heterozygotes demonstrated higher chimerism than wild-type pups (1.6 vs. 0.7%). Fetal liver cells produced higher chimerism compared to adult BM when transplanted at the same doses, maintaining 1.8-2.4% chimerism over ~32 weeks. We boosted transplanted mice postnatally with adult BM cells following busulfan conditioning. Engraftment was maintained at >1% only in recipients which were chimeric prior to boosting. IUHCT-treated non-chimeras and non-IUHCT mice showed micro- or no chimerism. Additional fludarabine treatment produced higher chimerism than busulfan alone. Engraftment was more effective following higher starting chimerism prior to boosting and in heterozygotes. Chimeric heterozygotes expressed 2.2-15.1% donor cells with eventual decline at 24 weeks (vs. <1% in non-chimeras) and demonstrated improved haematological indices and smaller spleens compared to untreated heterozygotes. Intravenous delivery of GLOBE lentiviral-vector expressing HBB (human β-globin) resulted in vector concentration of 0.001-0.6 copies/cell. Most haematological indices were higher in treated than untreated heterozygotes including haemoglobin and mean corpuscular volume, though still lower than in wild-types. Thus both direct IUGT and IUHCT strategies can be used to achieve haematological improvement but require further dose optimisation. IUHCT will be useful combined with postnatal transplantation to further enhance engraftment
Activity driven modeling of time varying networks
Network modeling plays a critical role in identifying statistical
regularities and structural principles common to many systems. The large
majority of recent modeling approaches are connectivity driven. The structural
patterns of the network are at the basis of the mechanisms ruling the network
formation. Connectivity driven models necessarily provide a time-aggregated
representation that may fail to describe the instantaneous and fluctuating
dynamics of many networks. We address this challenge by defining the activity
potential, a time invariant function characterizing the agents' interactions
and constructing an activity driven model capable of encoding the instantaneous
time description of the network dynamics. The model provides an explanation of
structural features such as the presence of hubs, which simply originate from
the heterogeneous activity of agents. Within this framework, highly dynamical
networks can be described analytically, allowing a quantitative discussion of
the biases induced by the time-aggregated representations in the analysis of
dynamical processes.Comment: 10 pages, 4 figure
Silica aerogel infused hierarchical glass fiber polymer composites
Hierarchical systems can address the matrix-dominated failures of structural fiber polymer composites. Here, a new synergistic hierarchical structure combines conventional structural glass fibers with a bi-continuous silica-based aerogel matrix; both pure-silica and organically-modified silicate aerogels are demonstrated. When infused with an epoxy matrix, this type of hierarchical architecture showed a marked improvement in mechanical properties: without any loss in modulus, both the compressive strength and the interlaminar shear strength increased by up to 27%, relative to the equivalent glass-fiber reinforced epoxy composite baseline. The bi-continuous network modification strategy uses industrially-relevant infusion techniques, at or near room temperature, and retains a similar final composite density (within 2%). The strategy presented here provides a versatile and readily applicable means to improve state-of-the art continuous fiber reinforced composite systems in compression and offers an opportunity to develop a new generation of composite materials
- …