Highly porous activated glassy carbon film sandwich structure for electrochemical energy storage in ultracapacitor applications: Study of the porous film structure and gradient

Glassy carbon plates were thermochemically gas phase oxidized to obtain monolithic sandwichlike electrode assemblies with high surface area porous films for electrochemical energy storage applications. Film thicknesses were varied by variation of oxidation parameters time, temperature, and oxygen concentration and measured with electron microscopy. The mass density of the porous carbon film material was estimated by fitting a geometrical model to experimental gravimetric data. Optical Raman spectroscopy line scans suggest that the porosity has a gradient between the surface and the film/bulk interface, which is supported by pore-size distribution data obtained from small-angle x-ray scattering (SAXS) on slightly oxidized and fully oxidized samples. Detailed inspection of the power law behavior of SAXS data suggests that the internal surface area of well-oxidized glassy carbon (GC) is compact and extends over the entire probed volume and thus has optimal pore connectivity. This effect goes along with pore enlargement and a relative decrease of internal surface area per volume. Slightly oxidized carbon has no pore space with a compact, high connectivity internal surface area. The corresponding SAXS power law and the x-ray density suggest that this high volumetric surface area must be interpreted as a result of surface roughness, rather than true geometric or volumetric surface area. In consequence, is this surface area of limited use for electrochemical energy storage

Phase Coexistence in Single-Lipid Membranes Induced by Buffering Agents

Recent literature has shown that buffers affect the interaction between lipid bilayers through a mechanism that involves van der Waals forces, electrostatics, hydration forces and membrane bending rigidity. This letter shows an additional peculiar effect of buffers on the mixed chain 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) lipid bilayers, namely phase coexistence similar to what was reported by Rappolt et al. for alkali chlorides. The data presented suggest that one phase appears to dehydrate below the value in pure water, while the other phase swells as the concentration of buffer is increased. However, since the two phases must be in osmotic equilibrium with one another, this behavior challenges theoretical models of lipid interactions

Reorganization of Ternary Lipid Mixtures of Non-Phosphorylated Phosphatidylinositol Interacting with Angiomotin

Phosphatidylinositol (PI) lipids are necessary for many cellular signaling pathways of membrane associated proteins, such as Angiomotin (Amot). The Amot family regulates cellular polarity, growth, and migration. Given the low concentration of PI lipids in these membranes, it is likely that such protein-membrane interactions are stabilized by lipid domains or small lipid clusters. By small-angle x-ray scattering, we show that non-phosphorylated PI lipids induce lipid de-mixing in ternary mixtures of phosphatidylcholine (PC) and phosphatidylethanolamine (PE), likely due to preferential interactions between the head groups of PE and PI. These results were obtained in the presence of buffer containing concentrations of Tris, HEPES, NaCl, EDTA, DTT, and Benzamidine at pH 8.0 that in previous work showed an ability to cause PC to phase separate but are necessary to stabilize Amot for in vitro experimentation. Collectively, this provided a framework for determining the effect of Amot on lipid organization. Using fluorescence spectroscopy, we were able to show that the association of Amot with this lipid platform causes significant reorganization of the lipid into a more homogenous organization. This reorganization mechanism could be the basis for Amot membrane association and fusigenic activity previously described in the literature and should be taken into consideration in future protein-membrane interaction studies

Programmable Colloidal Approach to Hierarchical Structures of Methylammonium Lead Bromide Perovskite Nanocrystals with Bright Photoluminescent Properties

Systematic tailoring of nanocrystal architecture could provide unprecedented control over their electronic, photophysical, and charge transport properties for a variety of applications. However, at present, manipulation of the shape of perovskite nanocrystals is done mostly by trial-and-error-based experimental approaches. Here, we report systematic colloidal synthetic strategies to prepare methylammonium lead bromide quantum platelets and quantum cubes. In order to control the nucleation and growth processes of these nanocrystals, we appropriately manipulate the solvent system, surface ligand chemistry, and reaction temperature causing syntheses into anisotropic shapes. We demonstrate that both the presence of chlorinated solvent and a long chain aliphatic amine in the reaction mixture are crucial for the formation of ultrathin quantum platelets (∼2.5 nm in thickness), which is driven by mesoscale-assisted growth of spherical seed nanocrystals (∼1.6 nm in diameter) through attachment of monomers onto selective crystal facets. A combined surface and structural characterization, along with small-angle X-ray scattering analysis, confirm that the long hydrocarbon of the aliphatic amine is responsible for the well ordered hierarchical stacking of the quantum platelets of 3.5 nm separation. In contrast, the formation of ∼12 nm edge-length quantum cubes is a kinetically driven process in which a high flux of monomers is achieved by supplying thermal energy. The photoluminescence quantum yield of our quantum platelets (∼52%) is nearly 2-fold higher than quantum cubes. Moreover, the quantum platelets display a lower nonradiative rate constant than that found with quantum cubes, which suggests less surface trap states. Together, our research has the potential both to improve the design of synthetic methods for programmable control of shape and assembly and to provide insight into optoelectronic properties of these materials for solid-state device fabrication, e.g., light-emitting diodes, solar cells, and lasing materials

Nanoscale morphology of polyanhydride copolymers

The microphase separation in polyanhydride random copolymers composed of 1,6-bis(p-carboxyphenoxy)hexane and sebacic acid is described. Though the copolymers are random, the monomers are sufficiently long and the segment-segment interaction parameter is sufficiently high to promote microphase separation when the copolymer is rich in one component. Solid-state NMR spin diffusion experiments and synchrotron small-angle X-ray scattering are used to discern the length scales of the microphase separation. Both techniques reveal a nanostructure with domain sizes less than 25 Ã…. This nanostructure is compared to approximate calculations of chain dimensions based on a random coil model and discussed in the context of the rational design of these materials for drug delivery applications

Dual Anion-Cation Ionic Liquid Crystal for Battery Applications

Ionic liquid crystals (ILCs) are a special class of compounds that not only contains mesogens group but also have cationic and/or anionic components. ILCs can self-organize into assemblies with varying degrees of orientational order resulting into formation of unique liquid crystal phases. Thermotropic ionic liquid crystals are special subclass of liquid crystal containing ionic liquid moiety that self- assemble with application of heat to form liquid crystal phases. Thermotropic ionic liquid crystal materials may exhibit several mesogenic phases at differing temperatures, distinguishable by the degree of order. This work mainly focuses on synthesis and characterization of Ionic liquid Crystals containing imidazolium and sulfonimide functional group attached to phenyl ring containing long chain alkyl group. In this presentation we will focus on how change in alkyl tail, change in ionic component (sulfonimide vs imidazolium) , and counter ion (i.e., triethyl ammonium vs Lithium cation) present in the compound, affect the liquid crystal properties. The synthesized ILCs was characterized by TGA, DSC and SAXS data. Keywords: Ionic liquids, Liquid crystals, Dual Cation-Anion, Batterie

Ultrathin Plasmonic Tungsten Oxide Quantum Wells with Controllable Free Carrier Densities

Localized surface plasmon resonances (LSPR) of nanostructures can be tuned by controlling their morphology, local dielectric environment, and free carrier concentration. We report the colloidal synthesis of an ∼3 tungsten–oxygen (W-O) layer thick (∼1 nm), two-dimensional (2D) WO3-x nanoplatelets (NPLs) (x ≈ 0.55–1.03), which display tunable near-infrared LSPR properties and additionally high free electron density (Ne) that arises predominantly from the large shape factor of 2D NPLs. Importantly, the W to O composition ratios inferred from their LSPR measurements show much higher percentage of oxygen vacancies than those determined by X-ray diffraction analysis, suggesting that the aspect ratio of ultrathin WO3-x NPLs is the key to producing an unprecedentedly large Ne, although synthesis temperature is also an independent factor. We find that NPL formation is kinetically controlled, whereas thermodynamic parameter manipulation leads to Ne values as high as 4.13 × 1022 cm–3, which is close to that of plasmonic noble metals, and thus our oxide-based nanostructures can be considered as quasi-metallic. The unique structural properties of 2D nanomaterials along with the high Ne of WO3-x NPLs provide an attractive alternative to plasmonic noble metal nanostructures for various plasmon-driven energy conversions and design of photochromic nanodevices

Nanoassemblies of ultrasmall clusters with remarkable activity in carbon dioxide conversion into C1 fuels

Cu nanoassemblies formed transiently during reaction from size-selected subnanometer Cu4 clusters supported on amorphous OH-terminated alumina convert CO2 into methanol and hydrocarbons under near-atmospheric pressure at rates considerably higher than those of individually standing Cu4 clusters. An in situ characterization reveals that the clusters self-assemble into 2D nanoassemblies at higher temperatures which then disintegrate upon cooling down to room temperature. DFT calculations postulate a formation mechanism of these nanoassemblies by hydrogen-bond bridges between the clusters and H2O molecules, which keep the building blocks together while preventing their coalescence