3,446 research outputs found
Development of procedures for calculating stiffness and damping properties of elastomers in engineering applications. Part 4: Testing of elastomers under a rotating load
A test rig designed to measure stiffness and damping of elastomer cartridges under a rotating load excitation is described. The test rig employs rotating unbalance in a rotor which runs to 60,000 RPM as the excitation mechanism. A variable resonant mass is supported on elastomer elements and the dynamic characteristics are determined from measurements of input and output acceleration. Five different cartridges are considered: three of these are buttons cartridges having buttons located in pairs, with 120 between each pair. Two of the cartridges consist of 360 elastomer rings with rectangular cross-sections. Dynamic stiffness and damping are measured for each cartridge and compared with predictions at different frequencies and different strains
Development of procedures for calculating stiffness and damping properties of elastomers. Part 3: The effects of temperature, dissipation level and geometry
Effects of temperature, dissipation level and geometry on the dynamic behavior of elastomer elements were investigated. Force displacement relationships in elastomer elements and the effects of frequency, geometry and temperature upon these relationships are reviewed. Based on this review, methods of reducing stiffness and damping data for shear and compression test elements to material properties (storage and loss moduli) and empirical geometric factors are developed and tested using previously generated experimental data. A prediction method which accounts for large amplitudes of deformation is developed on the assumption that their effect is to increase temperature through the elastomers, thereby modifying the local material properties. Various simple methods of predicting the radial stiffness of ring cartridge elements are developed and compared. Material properties were determined from the shear specimen tests as a function of frequency and temperature. Using these material properties, numerical predictions of stiffness and damping for cartridge and compression specimens were made and compared with corresponding measurements at different temperatures, with encouraging results
The Habitable Zone Gallery
The Habitable Zone Gallery (www.hzgallery.org) is a new service to the
exoplanet community which provides Habitable Zone (HZ) information for each of
the exoplanetary systems with known planetary orbital parameters. The service
includes a sortable table with information on the percentage of orbital phase
spent within the HZ, planetary effective temperatures, and other basic
planetary properties. In addition to the table, we also plot the period and
eccentricity of the planets with respect to their time spent in the HZ. The
service includes a gallery of known systems which plot the orbits and the
location of the HZ with respect to those orbits. Also provided are animations
which aid in orbit visualization and provide the changing effective temperature
for those planets in eccentric orbits. Here we describe the science motivation,
the under-lying calculations, and the structure of the web site.Comment: 6 pages, 3 figures, accepted for publication in PAS
Spray automated balancing of rotors: Methods and materials
The work described consists of two parts. In the first part, a survey is performed to assess the state of the art in rotor balancing technology as it applies to Army gas turbine engines and associated power transmission hardware. The second part evaluates thermal spray processes for balancing weight addition in an automated balancing procedure. The industry survey reveals that: (1) computerized balancing equipment is valuable to reduce errors, improve balance quality, and provide documentation; (2) slow-speed balancing is used exclusively, with no forseeable need for production high-speed balancing; (3) automated procedures are desired; and (4) thermal spray balancing is viewed with cautious optimism whereas laser balancing is viewed with concern for flight propulsion hardware. The FARE method (Fuel/Air Repetitive Explosion) was selected for experimental evaluation of bond strength and fatigue strength. Material combinations tested were tungsten carbide on stainless steel (17-4), Inconel 718 on Inconel 718, and Triballoy 800 on Inconel 718. Bond strengths were entirely adequate for use in balancing. Material combinations have been identified for use in hot and cold sections of an engine, with fatigue strengths equivalent to those for hand-ground materials
Small, high-speed bearing technology for cryogenic turbo-pumps
The design of 20-mm bore ball bearings is described for cryogenic turbo-machinery applications, operating up to speeds of 120,000 rpm. A special section is included on the design of hybrid bearings. Each hybrid bearing is composed of a ball bearing in series with a conventional pressurized fluid-film journal bearing. Full details are presented on the design of a test vehicle which possesses the capability of testing the above named bearings within the given speed range under externally applied radial and axial loads
Development of procedures for calculating stiffness and damping of elastomers in engineering applications. Part 5: Elastomer performance limits and the design and test of an elastomer damper
Tests were performed on elastomer specimens of the material polybutadiene to determine the performance limitations imposed by strain, temperature, and frequency. Three specimens were tested: a shear specimen, a compression specimen, and a second compression specimen in which thermocouples were embedded in the elastomer buttons. Stiffness and damping were determined from all tests, and internal temperatures were recorded for the instrumented compression specimen. Measured results are presented together with comparisons between predictions of a thermo-viscoelastic analysis and the measured results. Dampers of polybutadiene and Viton were designed, built, and tested. Vibration measurements were made and sensitivity of vibration to change in unbalance was also determined. Values for log decrement were extracted from the synchronous response curves. Comparisons were made between measured sensitivity to unbalance and log decrement and predicted values for these quantities
On the anomaly of Balmer line profiles of A-type stars. Fundamental binary systems
In previous work, Gardiner et al. (1999) found evidence for a discrepancy
between the Teff obtained from Balmer lines with that from photometry and
fundamental values for A-type stars. An investigation into this anomaly is
presented using Balmer line profiles of stars in binary system with fundamental
values of both Teff and log g. A revision of the fundamental parameters for
binary systems given by Smalley & Dworetsky (1995) is also presented. The Teff
obtained by fitting Halpha and Hbeta line profiles is compared to the
fundamental values and those obtained from uvby photometry. We find that the
discrepancy found by Gardiner et al. (1999) for stars in the range 7000 K <
Teff < 9000 K is no longer evident.Comment: 10 pages, 4 figures; Accepted by A&
MicroRNA dysregulation and esophageal cancer development depend on the extent of zinc dietary deficiency
open9siopenFong, Louise Y.; Taccioli, Cristian; Jing, Ruiyan; Smalley, Karl J.; Alder, Hansjuerg; Jiang, Yubao; Fadda, Paolo; Farber, John L.; Croce, Carlo M.Fong, Louise Y.; Taccioli, Cristian; Jing, Ruiyan; Smalley, Karl J.; Alder, Hansjuerg; Jiang, Yubao; Fadda, Paolo; Farber, John L.; Croce, Carlo M
- …