23 research outputs found
Benchmarking the Self-Assembly of Surfactin Biosurfactant at the Liquid–Air Interface to those of Synthetic Surfactants
The adsorption of surfactin, a lipopeptide biosurfactant, at the liquid–air interface has been investigated in this work. The maximum adsorption density and the nature and the extent of lateral interaction between the adsorbed surfactin molecules at the interface were estimated from surface tension data using the Frumkin model. The quantitative information obtained using the Frumkin model was also compared to those obtained using the Gibbs equation and the Langmuir–Szyszkowski model. Error analysis showed a better agreement between the experimental and the calculated values using the Frumkin model relative to the other two models. The adsorption of surfactin at the liquid–air interface was also compared to those of synthetic anionic, sodium dodecylbenzenesulphonate (SDBS), and nonionic, octaethylene glycol monotetradecyl ether (C14E8), surfactants. It has been estimated that the area occupied by a surfactin molecule at the interface is about 3- and 2.5-fold higher than those occupied by SDBS and C14E8 molecules, respectively. The interaction between the adsorbed molecules of the anionic biosurfactant (surfactin) was estimated to be attractive, unlike the mild repulsive interaction between the adsorbed SDBS molecules
Benchmarking the Self-Assembly of Surfactin Biosurfactant at the Liquid–Air Interface to those of Synthetic Surfactants
Effect of ionic surfactants on drainage and equilibrium thickness of emulsion films
This paper presents new theoretical and experimental results that quantify the role of surfactant adsorption and the related interfacial tension changes and interfacial forces in the emulsion film drainage and equilibrium. The experimental results were obtained with plane-parallel microscopic films from aqueous sodium dodecyl sulphate solutions formed between two toluene droplets using an improved micro-interferometric technique. The comparison between the theory and the experimental data show that the emulsion film drainage and equilibrium are controlled by the DLVO interfacial forces. The effect of interfacial viscosity and interfacial tension gradient (the Marangoni number) on the film drainage is also significant
Elasticity of foam bubbles measured by profile analysis tensiometry
Elastic modulus of foam bubbles, stabilized with tetraethylene glycol octyl ether (C(8)E(4)) and 1 x 10(-5) M NaCl, was determined by cyclic expansion and shrinking of foam bubbles with frequency of 0.1 Hz and volumetric amplitude of 2 mm(3). The film tension was monitored by a commercial profile analysis tensiometer (Sinterface Technologies, GmbH). The elastic moduli of foam bubbles were obtained as a function of surfactant concentration in the range of 2 x 10(-3)-1 x 10(-2) M. The theory of Lucassen and van den Tempel Ill for the elastic modulus of a single liquid/air interface at a given frequency was employed. In the theoretical analysis the bulk diffusion coefficient of surfactant molecules was considered as a unknown model parameter which was obtained by matching the theory with the experimental data. Hence, the dependence of the bulk diffusion coefficient of C(8)E(4) molecules upon the C(8)E(4) concentration was obtained. The diffusion coefficient reached a maximum at 5 x 10(-3) M C(8)E(4) (D=8.5 x 10(-11) m(2)/s). In the experimental surfactant concentration range (2 x 10(-3)-1 x 10(-2) M, CMC=7.5 x 10(-3) M) the foam bubbles were relatively dry, with visible interferometric fringes corresponding to thin films stabilized by repulsion of the electrostatic disjoining pressure. Hence, the overall dynamics of periodical expansion and shrinking of the foam bubbles occurred within the thin film state. (C) 2010 Elsevier B.V. All rights reserved
Duality of foam stabilization
Can a foam reversibly switch between particle and surfactant stabilization? Sure it can. Foams are usually stabilized either by surfactant or hydrophobic nanoparticles. Their combination often worsens the stability of the foam, with surfactant adsorption on the particles causing complex behavior. A system that shifts between both types of mechanisms is desirable both for fundamental studies and practical applications. We developed a system consisting of aqueous solution of 0.1 mM sodium dodecyl sulfate (SDS) + 1.23 mM ZnSO4 + 1.23 mM ethylenediaminetetraacetic acid (EDTA). The foam was produced by the shaking method. The pH value was varied by small additions of HCl or NaOH. We tuned the foam lifetime from 15 to 20 s (at pH = 3 – 6), to ~ 180 s near pH = 1, and increase it in the pH range of 6–12, reaching 15 min at pH = 12. This is due to emerging of nanoparticles of Zn(OH)2 at pH > 8, smoothly switching between the stabilization mechanisms. The nano-suspension of Zn(OH)2 is transparent due to the low aggregation. The low cost (<$1 per metric ton) and the large timescales makes our system desirable for industrial applications
Ion-specific effects in foams
We present a critical review on ion-specific effects in foams in the presence of added salts. We show the theoretical basis developed for understanding experimental data in systems with ionic surfactants, as well as the nascent approaches to modelling the much more difficult systems with non-ionic surfactants, starting with the most recent models of the air-water interface. Even in the case of ionic surfactant systems, we show methods for improving the theoretical understanding and apply them forto interpretation of surprising experimental results we have obtained on ion-specific effects in these systems. our own. We report unexpectedly strong ion-specific effects of counter-ions on the stability and the rate of drainage of planar foam films from solutions of 0.5 mM Sodium dodecyl sulfate (SDS) as a function of concentration of a series of inorganic salts (MCl, M=Li, Na, K). We found that the counter-ions can either stabilize the foam films (up to a critical concentration) or destabilize them beyond it. The ordering for destabilization is in the same order as the Hofmeister series, while for stabilization it is the reverse Therefore, the strongest foam stabilizer (K+), becomes the strongest foam destabilizer at and beyond its critical concetration, and vice versa. Though the critical concentration is different for different salts, by calculating the critical surfactant adsorption level one could simplify the analysis, with all the critical concentrations occuring at the same surfactant adbsorption level. Beyond this level, the foam lifetime decreases and films suddenly start draining faster, which may indicate salt-induced surfactant precipitation. Alternatively, formation of pre-micellar structures may result in slower equilibration and fewer surfactant molecules at the surface, thus leading to unstable foams and films
Effect of the adsorption component of the disjoining pressure on foam film drainage
The present work is trying to explain a discrepancy between experimental observations of the drainage of foam films from aqueous solutions of sodium dodecylsulfate and the theoretical DLVO-accomplished Reynolds model. It is shown that, due to overlap of the film adsorption layers, an adsorption component of the disjoining pressure is important for the present system. The pre-exponential factor of this adsorption component was obtained by fitting to the experimental drainage curves. It corresponds to a slight repulsion, which reduces not only the thinning velocity as observed experimentally but corrects also the film equilibrium thickness