Characterisation of a novel reverse-biased PPD CMOS image sensor

A new pinned photodiode (PPD) CMOS image sensor (CIS) has been developed and characterised. The sensor can be fully depleted by means of reverse bias applied to the substrate, and the principle of operation is applicable to very thick sensitive volumes. Additional n-type implants under the pixel p-wells, called Deep Depletion Extension (DDE), have been added in order to eliminate the large parasitic substrate current that would otherwise be present in a normal device. The first prototype has been manufactured on a 18 μm thick, 1000 Ω .cm epitaxial silicon wafers using 180 nm PPD image sensor process at TowerJazz Semiconductor. The chip contains arrays of 10 μm and 5.4 μm pixels, with variations of the shape, size and the depth of the DDE implant. Back-side illuminated (BSI) devices were manufactured in collaboration with Teledyne e2v, and characterised together with the front-side illuminated (FSI) variants. The presented results show that the devices could be reverse-biased without parasitic leakage currents, in good agreement with simulations. The new 10 μm pixels in both BSI and FSI variants exhibit nearly identical photo response to the reference non-modified pixels, as characterised with the photon transfer curve. Different techniques were used to measure the depletion depth in FSI and BSI chips, and the results are consistent with the expected full depletion

Measurement does not always aid state discrimination

We have investigated the problem of discriminating between nonorthogonal quantum states with least probability of error. We have determined that the best strategy for some sets of states is to make no measurement at all, and simply to always assign the most commonly occurring state. Conditions which describe such sets of states have been derived.Comment: 3 page

Intuitive programming with remotely instructed robots inside future gloveboxes

Our research aims at facilitating the design of ’Remotely Instructed Robots’ for future glove-boxes in the nuclear industry. The two main features of such systems are: (1) They can automatically model the working environment and relay that information to the operator in virtual reality (VR). (2) They can receive instructions from the operator that are executed by the robot. However, the deficiency of these kind of systems is that they heavily rely on knowledge of expert programmers when the robot’s capabilities or hardware are to be reconfigured, altered or upgraded. This late breaking report proposes to introduce a third important advancement on remotely instructed robots: (3) Intuitive programming modifications by operators who are non-programmers but have basic knowledge of hardware, and most importantly, have experience of the weaknesses in particular handling tasks

Finding optimal strategies for minimum-error quantum-state discrimination

We propose a numerical algorithm for finding optimal measurements for quantum-state discrimination. The theory of the semidefinite programming provides a simple check of the optimality of the numerically obtained results.Comment: 4 pages, 2 figure

Surface Modification of Polyethylene with Multi-End-Functional Polyethylene Additives

We have prepared and characterized a series of multifluorocarbon end-functional polyethylene additives, which when blended with polyethylene matrices increase surface hydrophobicity and lipophobicity. Water contact angles of >112° were observed on spin-cast blended film surfaces containing less than 1% fluorocarbon in the bulk, compared to 98° in the absence of any additive. Crystallinity in these films gives rise to surface roughness that is an order of magnitude greater than is typical for amorphous spin-cast films but is too little to give rise to superhydrophobicity. X-ray photoelectron spectroscopy (XPS) confirms the enrichment of the multifluorocarbon additives at the air surface by up to 80 times the bulk concentration. Ion beam analysis was used to quantify the surface excess of the additives as a function of composition, functionality, and molecular weight of either blend component. In some cases, an excess of the additives was also found at the substrate interface, indicating phase separation into self-stratified layers. The combination of neutron reflectometry and ion beam analysis allowed the surface excess to be quantified above and below the melting point of the blended films. In these films, where the melting temperatures of the additive and matrix components are relatively similar (within 15 °C), the surface excess is almost independent of whether the blended film is semicrystalline or molten, suggesting that the additive undergoes cocrystallization with the matrix when the blended films are allowed to cool below the melting point

Optimal discrimination of mixed quantum states involving inconclusive results

We propose a generalized discrimination scheme for mixed quantum states. In the present scenario we allow for certain fixed fraction of inconclusive results and we maximize the success rate of the quantum-state discrimination. This protocol interpolates between the Ivanovic-Dieks-Peres scheme and the Helstrom one. We formulate the extremal equations for the optimal positive operator valued measure describing the discrimination device and establish a criterion for its optimality. We also devise a numerical method for efficient solving of these extremal equations.Comment: 5 pages, 1 figur

Symmetries and Elasticity of Nematic Gels

A nematic liquid-crystal gel is a macroscopically homogeneous elastic medium with the rotational symmetry of a nematic liquid crystal. In this paper, we develop a general approach to the study of these gels that incorporates all underlying symmetries. After reviewing traditional elasticity and clarifying the role of broken rotational symmetries in both the reference space of points in the undistorted medium and the target space into which these points are mapped, we explore the unusual properties of nematic gels from a number of perspectives. We show how symmetries of nematic gels formed via spontaneous symmetry breaking from an isotropic gel enforce soft elastic response characterized by the vanishing of a shear modulus and the vanishing of stress up to a critical value of strain along certain directions. We also study the phase transition from isotropic to nematic gels. In addition to being fully consistent with approaches to nematic gels based on rubber elasticity, our description has the important advantages of being independent of a microscopic model, of emphasizing and clarifying the role of broken symmetries in determining elastic response, and of permitting easy incorporation of spatial variations, thermal fluctuations, and gel heterogeneity, thereby allowing a full statistical-mechanical treatment of these novel materials.Comment: 21 pages, 4 eps figure

Precision wildlife monitoring using unmanned aerial vehicles

Unmanned aerial vehicles (UAVs) represent a new frontier in environmental research. Their use has the potential to revolutionise the field if they prove capable of improving data quality or the ease with which data are collected beyond traditional methods. We apply UAV technology to wildlife monitoring in tropical and polar environments and demonstrate that UAV-derived counts of colony nesting birds are an order of magnitude more precise than traditional ground counts. The increased count precision afforded by UAVs, along with their ability to survey hard-to-reach populations and places, will likely drive many wildlife monitoring projects that rely on population counts to transition from traditional methods to UAV technology. Careful consideration will be required to ensure the coherence of historic data sets with new UAV-derived data and we propose a method for determining the number of duplicated (concurrent UAV and ground counts) sampling points needed to achieve data compatibility.Jarrod C. Hodgson, Shane M. Baylis, Rowan Mott, Ashley Herrod & Rohan H. Clark