245 research outputs found
Recommended from our members
Evaluation of Toughness of High Strength Low Alloy (HSLA) Steels as a Function of Carbon Content
The influence of carbon content on the microstructure and toughness of HSLA steel at room temperature was investigated based on experimental work and literature. It was revealed that increasing the carbon content in from 0.06 to 0.14 wt-% is detrimental to toughness, giving higher impact transition temperature. The deterioration of toughness was correlated to undesired changes in the microstructure, which showed an increase in pearlite volume fraction at the expense of ferrite. At high carbon content, cementite of pearlite was found to grow more rapidly to form continuous plates which act as preferred sites for crack nucleation and propagation. In addition, the lamellar spacing of the pearlite increased as a function of carbon content, which in turn gave worse toughness. The presence of high carbon content and carbide forming elements in the chemical composition was more detrimental to toughness due to the formation of thick carbides around the grain boundaries. These carbides act as a path for crack propagation, which makes it easy for cracks to cohere, leading to intergranular fracture. Keywords - HSLA steel, Carbon, Brittleness, Toughness, Impact Transition Temperature (ITT)
Recommended from our members
The influence of Widmanstätten ferrite, martensite and grain boundary carbides on the strength and impact behaviour of high Al (0.2%) and Nb containing hot rolled steels
The influence of Al and Nb on the strength and impact behaviour of hot rolled 0.06%C, 1.4%Mn steels has been determined after hot rolling to 15 and 30 mm thick plate. When 0.16%Al was added to the plain C-Mn steel, the impact behaviour significantly improved even though Widmanstätten ferrite (WF) was present. This improvement was due to refinement of the grain boundary carbides and removing the N from solution as AlN. The hot rolled steels all contained WF but when Nb was added more WF formed as well as MA giving poor impact behaviour. Reducing the hardenability from that shown in previous work by decreasing C from 0.1 to 0.06%, Nb from 0.03 to 0.02%, and cooling rate from 33 to 17 K/min had no effect in improving the impact performance of hot rolled Nb steels. To ensure optimum properties not only is it necessary to reduce the hardenability, but WF formation must be discouraged by having a high Ar3. This can only be presently achieved by refining the austenite grain size via control rolling the Nb containing steels; the benefit of adding Al can then, readily be seen. Suggestions are made as to how this might be achieved for hot rolling
Recommended from our members
Influence of Al content on the corrosion resistance of micro-alloyed hot rolled steel as a function of grain size
High-strength low-alloy steel (HSLA) has been widely used in many applications involving automobiles, aerospace, construction, and oil and gas pipelines due to their enhanced mechanical and chemical properties. One of the most critical elements used to improve these properties is Aluminium. This work will explore the effect of Al content on the corrosion behaviour of hot rolled high-strength low-alloy steel as a function of grain size. The method of investigation employed was weight loss technique. It was obvious that the increase in Al content enhanced corrosion resistance through refinement of grain size obtained through AlN precipitation by pinning grain boundaries and hindering their growth during solidification which was found to be beneficial in reducing corrosion rate
Recommended from our members
3D Thermal Model of Laser Surface Glazing for Ti6Al4V alloy
t: Ti6Al4V alloy plays a significant role in the biomedical applications such as bioimplants for its excellent biocompatibility. Its usage can be further extended by improving the surface hardness and wear resistance. In this respect, laser surface glazing (LSG), an advanced surface modification technique, is very useful which can produce thin hardened surface layer and strong metallurgical bonding. Investigation of temporal and spatial temperature distributions of laser glazed surface of materials are essential because temperature plays significant role in achieving required surface properties. Therefore, in this study, a 3D Finite element analysis has been developed to perform transient thermal analysis of LSG for Ti64 alloy. The model investigated temperature distribution, depth of modified zone and heating and cooling. The results show that the peak temperature is attained 2095 K for 300 W laser power, 0.2 mm beam width and 0.15 ms residence time. Since this temperature is above the melting point (1933 K) of Ti64 alloy, the melt depth is calculated 22.5 μm. Furthermore, from the simulation results, the average heating and cooling rates are estimated 1.19×107 Ks-1 and 2.71×106 Ks-1 respectively which indicate the presence of hard phases in the modified zone
Recommended from our members
Injection tests and effect on microstructure and properties of aluminium 7075 direct thermal method feedstock billets
The success of semi-solid metal forming is dependent on a globular solid grain formation within a liquid phase. This paper presents experimental works concerning semi-solid metal processing of aluminium 7075 feedstock billets which were produced by direct thermal method. The flowability of feedstock billets was evaluated by an injection test processing unit. The feedstock billets were heated to a temperature of 620 °C by using a box furnace before transferred into a forming die. The formed feedstock billet was removed from the forming die after it was cooled to ambient temperature. Several analyses were conducted on the formed feedstock billets including dimensional measurement and microstructure analysis. The results show that the feedstock billets which contained the highest amount of free secondary phase were most successfully formed. Microstructure analysis results also revealed the formation of more globular and larger α–Al solid grains in the same feedstock billets. In this experimental work, the feedstock billets with higher amount of secondary (liquid) phase had a significant effect on formability. It is concluded that in order to achieve successful formability of the direct thermal method feedstock billets, the billets need to a have higher secondary phase content. Thus, important preparation methods of feedstock billets were characterised in order to allow for SSM processing
Recommended from our members
A One-dimensional Analysis of the Distribution of Temperature, Stress and Strain in the co-axial Laser Cladding Process
The co-axial Laser Cladding (LC) is one of the most advanced surface treatment processes where generally a superior powder or wire material is deposited on the substrate to improve surface properties by using laser heat source. In this work, a physical model of the clad and the substrate has been presented. An attempt has been made to describe the simplified relation of temperature, stress and strain with time by using the established theoretical knowledge of generation of stress and strain after thermal treatment. The simplified relation of temperature, stress and strain with time has been explained with the help of schematic diagrams. The finding of this study will help to understand the temperature, stress and strain behaviour with time in the Laser Cladding process
Recommended from our members
Atomic diffusion in laser surface modified AISI H13 steel
This paper presents a laser surface modification process of AISI H13 steel using 0.09 and 0.4 mm of laser spot sizes with an aim to increase surface hardness and investigate elements diffusion in laser modified surface. A Rofin DC-015 diffusion-cooled CO2 slab laser was used to process AISI H13 steel samples. Samples of 10 mm diameter were sectioned to 100 mm length in order to process a predefined circumferential area. The parameters selected for examination were laser peak power, pulse repetition frequency (PRF), and overlap percentage. The hardness properties were tested at 981 mN force. Metallographic study and energy dispersive X-ray spectroscopy (EDXS) were performed to observe presence of elements and their distribution in the sample surface. Maximum hardness achieved in the modified surface was 1017 HV0.1. Change of elements composition in the modified layer region was detected in the laser modified samples. Diffusion possibly occurred for C, Cr, Cu, Ni, and S elements. The potential found for increase in surface hardness represents an important method to sustain tooling life. The EDXS findings signify understanding of processing parameters effect on the modified surface composition
- …