Impact of the type of anodic film formed and deposition time on the characteristics of porous anodic aluminium oxide films containing Ni metal

Porous anodic films containing nickel were prepared by AC electro-deposition. The porosity of the films was controlled by using different working conditions (anodisation electrolyte, voltage, and time). Then nickel was electro-deposited using an alternating voltage. The impact of the anodic film on the current density waveforms and the metal content can largely be explained by the porosity differences, while changing the deposition time caused changes due to over-oxidation of the aluminium substrate, experimentally proved by TEM. Finally, the impact of deposition time on the deposited metal was successfully fitted using an Elovich type law over a large time-span (up to 1800 s), showing the ability to achieve precise control of the metal content

Comportement thermique du xénon dans le nitrure de titane fritté matrice inerte d’intérêt des RNR-G

This work concerns the generation IV future nuclear reactors such as gas-cooled fast reactor (GFR) for which refractory materials as titanium nitride (TiN) are needed to surround fuel and act as a fission product diffusion barrier. This study is about Xe thermal behavior in sintered titanium nitride. Microstructure effects on Xe behavior have been studied. In this purpose, several syntheses have been performed using differents sintering temperatures and initial powder compositions. Xenon species have been introduced into samples by ionic implantation. Then, samples were annealed in temperature range from 1300°C to 1600°C, these temperatures being the accidental awaited temperature. A transport of xenon towards sample surface has been observed. Transport rate seems to be slow down when increasing sintering temperature. The composition of initial powder and the crystallographic orientation of each considered grain also influence xenon thermal behavior. Xenon release has been correlated with material oxidation during annealing. Xenon bubbles were observed. Their size is proportional with xenon concentration and increases with annealing temperature. Several mechanisms which could explain Xe intragranular mobility in TiN are proposed. In addition with experiments, very low Xe solubility in TiN has been confirmed by ab initio calculations. So, bivacancies were found to be the most favoured Xe incorporation sites in this material.Ce travail se place dans le cadre des réacteurs nucléaires de 4ème génération tels que les réacteurs à neutrons rapides et caloporteur gaz (RNR-G), pour lesquels des matériaux réfractaires comme le nitrure de titane (TiN) enroberont le combustible afin de permettre la rétention des produits de fission. Cette étude a porté sur le comportement thermique intragranulaire du xénon dans des échantillons de TiN obtenus par frittage à chaud sous charge. Le rôle de la microstructure sur le comportement thermique du xénon a été étudié. Plusieurs lots ont ainsi été synthétisés sous différentes conditions de température et de composition de la poudre initiale. Le xénon a été introduit par implantation ionique. Les échantillons ont ensuite subi des traitements thermiques entre 1300°C et 1600°C, soient les températures accidentelles envisagées. Un transport majoritaire du xénon vers la surface a été mis en évidence. Ce dernier est ralenti lorsque la température de frittage augmente. Des différences de comportement ont été observées selon les poudres mises en oeuvre dans la synthèse et selon l'orientation cristalline du grain considéré. Le relâchement du xénon a également été corrélé à l’oxydation de TiN. Des bulles de Xe dès 0,38 % atomique ont été observées. Leur taille est proportionnelle à la concentration en Xe et augmente avec la température de recuit, d’où une certaine mobilité du Xe au sein de TiN. Plusieurs mécanismes pouvant expliquer cette mobilité sont proposés. En complément, des calculs ab initio ont confirmé le caractère fortement insoluble du Xe dans TiN et révélé que les bilacunes sont les plus favorables à l'incorporation du xénon au sein de ce matériau

Application of multi-edge HERFD-XAS to assess the uranium valence electronic structure in potassium uranate (KUO3)

The uranium valence electronic structure in the prototypical undistorted perovskite KUO3 is reported on the basis of a comprehensive experimental study using multi-edge HERFD-XAS and relativistic quantum chemistry calculations based on density functional theory. Very good agreement is obtained between theory and experiments, including the confirmation of previously reported Laporte forbidden f –f transitions and X-ray photoelectron spectroscopic measurements. Many spectral features are clearly identified in the probed U-f, U- p and U-d states and the contribution of the O-p states in those features could be assessed. The octahedral crystal field strength, 10Dq, was found to be 6.6 (1.5) eV and 6.9 (4) eV from experiment and calculations, respectively. Calculated electron binding energies down to U-4f states are also reported.Peer reviewe

Transformation of inherent microorganisms in Wyoming-type bentonite and their effects on structural iron

Bentonite is one of the materials used to construct engineered barriers in high-level radioactive nuclear waste geological disposal with its many advantageous features such as low hydraulic conductivity, self-sealing ability, durability, adsorption and immobilization of metals and radionuclides and reduction of microbial activity. Many of these properties are linked with the bentonite swelling capability. Transformations of indigenous microorganism communities from Wyoming-type bentonite and the Finnish repository site groundwater and their effects on the bentonite structural iron over five years were studied in repository relevant anoxic and oxic slurry conditions. Active sulfate reduction (0.06 nmol mL-1 day-1) was detected in the anoxic microcosm waters after a year, however after two years sulfate reduction was not active anymore. Microbial numbers determined by quantitative PCR in the bentonite slurry of both experiment types supported the finding of decrease of overall microbial activity after a year of incubation that was not maintained anymore by the dissolving organic carbon from the bentonite. Regular electron donor additions (final concentration of 2 mM for formate and acetate each, three times per year) activated the microbiome resulting in increasing numbers of bacterial 16S rRNA gene copies and sulfate reducers (dsrB gene copies) as well as detection of sulfide in the water phase of both experiment types. After 4.9 years the structural iron in the fine portion of the montmorillonite had become completely reduced in all microbial microcosms and minor smectite illitization was detected especially in anoxic microcosms. Dominating bacterial groups at the end of the experiment were mainly known sulfur/sulfate and iron reducers. Archaea and fungi constituted a minor part of the microbiomes. In originally oxic microcosms, the bacterial 16S RNA and dsrB gene copy numbers were lower than in the anoxic experiment but started to significantly increase after the electron donor additions. Microorganisms originating from the repository environment could reduce the bentonite structural iron in a few years to an extent likely to affect the bentonite swelling ability if sufficient amounts of suitable electron donors are available in localized areas where bentonite is not at high density and pressure in the geological disposal.Peer reviewe

Anion exchange on hydrous zirconium oxide materials: application for selective iodate removal

The radioactive 129I is a top-priority radionuclide due to its the long half-life (1.57 × 107 years) and high mobility. Because of the planned and accidental releases to the environment, specific separation technologies are required to limit the potential radiation dose to human beings. Zirconium oxides are known for their adsorption capability and selectivity to oxyanions and here the applicability to selective IO3− removal has been investigated regarding the uptake mechanism, regeneration and competition caused by other anions, like environmentally relevant SO42−. Granular aggregates of hydrous zirconium oxides with and without Sb doping showed high potential for the selective IO3− removal in the presence of competing anions, like the forementioned SO42− (apparent capacity between 0.1–0.4 meq g−1 depending on SO42− concentration). The main uptake mechanism was found to be outer-sphere complexation (ion-exchange) to the protonated hydroxyl groups of hydrous zirconium oxides, but also minor mechanisms were identified including inner-sphere complexation and reduction to I−. The materials were observed to be easily and successively regenerated using dilute acid. Hydrous zirconium oxides showed high potential for IO3− removal from waste solutions regarding technical (high selectivity and apparent capacity) and ecological/economic (feasible regeneration) aspects.The radioactive I-129 is a top-priority radionuclide due to its the long half-life (1.57 x 10(7) years) and high mobility. Because of the planned and accidental releases to the environment, specific separation technologies are required to limit the potential radiation dose to human beings. Zirconium oxides are known for their adsorption capability and selectivity to oxyanions and here the applicability to selective IO3- removal has been investigated regarding the uptake mechanism, regeneration and competition caused by other anions, like environmentally relevant SO42-. Granular aggregates of hydrous zirconium oxides with and without Sb doping showed high potential for the selective IO3- removal in the presence of competing anions, like the forementioned SO42- (apparent capacity between 0.1-0.4 meq g(-1) depending on SO42- concentration). The main uptake mechanism was found to be outer-sphere complexation (ion-exchange) to the protonated hydroxyl groups of hydrous zirconium oxides, but also minor mechanisms were identified including inner-sphere complexation and reduction to I-. The materials were observed to be easily and successively regenerated using dilute acid. Hydrous zirconium oxides showed high potential for IO3- removal from waste solutions regarding technical (high selectivity and apparent capacity) and ecological/economic (feasible regeneration) aspects.Peer reviewe

Laboratory-scale x-ray absorption spectroscopy of 3d transition metals in inorganic thin films

In this paper we present laboratory-scale X-ray absorption spectroscopy applied to the research of nanometer-scale thin films. We demonstrate the Cu K edge X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) of CuI and CuO thin films grown with atomic layer deposition. Film thicknesses in the investigated samples ranged from 12 to 248 nm. Even from the thinnest films, XANES spectra can be obtained in 5-20 minutes and EXAFS in 1-4 days. In order to prove the capability of laboratory-based XAS for in situ measurements on thin films, we demonstrate an experiment on in situ oxidation of a 248 nm thick CuI film at a temperature of 240 degrees C. These methods have important implications for novel and enhanced possibilities for inorganic thin film research.Peer reviewe

Effect of atomic layer deposited zinc promoter on the activity of copper-on-zirconia catalysts in the hydrogenation of carbon dioxide to methanol

The development of active catalysts for carbon dioxide (CO2) hydrogenation to methanol is intimately related to the creation of effective metal-oxide interfaces. In this work, we investigated how the order of addition of copper and zinc on zirconia influences the catalytic properties, the catalytic activity and selectivity toward methanol. Regarding the carbon dioxide conversion and methanol production, the catalysts on which the promoter (zinc) was atomically deposited after copper impregnation (i.e., ZnO/Cu/ZrO2 and ZnO/Cu/ZnO/ZrO2) were superior catalysts compared to the reverse copper-after-zinc catalyst (Cu/ZnO/ZrO2). Temperature-programmed experiments and in situ diffuse reflectance infrared Fourier transform-spectroscopy (DRIFTS) experiments allowed us to elucidate the benefits of the zinc-after-copper pair to store CO2 as carbonate species and further convert them into formate species, key intermediates in the formation of methanol. This research provides insights into the potential of atomic layer deposition in the development of tailored heterogeneous catalysts for efficient CO2 valorization to methanol.Peer reviewe

Methicillin-susceptible, Doxycycline-resistant Staphylococcus aureus, Côte d’Ivoire

This virulent clone has already spread to other continents

Electrical behaviour, characteristics and properties of anodic aluminium oxide films coloured by nickel electrodeposition

Porous anodic films on 1050 aluminium substrate were coloured by AC electrodeposition of nickel. Several experiments were performed at different deposition voltages and nickel concentrations in the electrolyte in order to correlate the applied electrical power to the electrical behaviour, as well as the characteristics and properties of the coatings. The content of nickel inside the coatings reached 1.67 g/m2, depending on the experimental conditions. According to the applied AC voltage in comparison with the threshold voltage Ut, the coating either acted only as a capacitor when U\Ut and, when U[Ut, the behaviour during the anodic and cathodic parts of the power sine wave was different. In particular, due to the semi-conducting characteristics of the barrier layer, additional oxidation of the aluminium substrate occurred during the anodic part of the electrical signal, whilst metal deposition (and solvent reduction) occurred during the cathodic part; these mechanisms correspond to the blocked and pass directions of the barrier layer/electrolyte junction, respectively

Modélisation et optimisation des transformations chimiques induites dans un plasma froid en système ouvert

La modélisation du fonctionnement d'un réacteur à plasma froid selon la nature de l'écoulement limite permet de généraliser l'utilisation du critère économique précédemment proposé pour la synthèse de l'ozone. On présente des exemples relatifs à la plupart des transformations chimiques mises en œuvre jusqu'ici : formation d'ozone à partir d'oxygène, de SO3 à partir de SO2 et O2 et décomposition de NH3, CO2 et CH4 pour donner essentiellement N2H4, O2 et H2