Coherence of a room-temperature CW GaAs/GaAlAs injection laser

The temporal coherence of a stripe-geometry double-heterojunction GaAs/GaAlAs laser operating CW at room temperature was determined. A heterodyne detection scheme was used involving the mixing of the laser field with a frequency-shifted and time-delayed image of itself in an interferometer. Because the laser device oscillated in several longitudinal modes, the autocorrelation function of its output exhibited resonances for specific time delays. The rate at which the amplitude of these resonances decreased with increasing time delays provided a measure of an apparent coherence length associated with individual longitudinal modes. The coherence length, so defined, was found to increase linearly with drive current in excess of threshold. This observation is interpreted as evidence that the intrinsic linewidth of a longitudinal mode is inversely proportional to the coherent optical power in that mode. Apparent coherence lengths were a few centimeters for a few milliwatts of total optical power emitted per facet. For a perfectly balanced interferometer, a sharp heterodyne beat signal was also observed when the laser device was operated considerably below threshold, i.e., in the LED mode

What are the triggers of Asian visitor satisfaction and loyalty in the Korean heritage site?

Based on complexity theory, this study examines a configurational model that uses motivation antecedents and demographic configurations to explore the causal recipes that lead to high and low levels of Asian visitor satisfaction and loyalty. Data were collected from 183 Chinese and Japanese visitors to the Hanok heritage site in Seoul, South Korea. Asymmetrical modeling using a fuzzy-set qualitative comparative analysis was applied and a combination of desired behavioral outcomes identified. Hanok experience from the motivation configuration and gender from the demographic configuration appeared as necessary conditions to make visitors satisfied and loyal. Key tenets of complexity theory are supported by the study's findings

Measurement, reporting and verification of livestock GHG emissions by developing countries in the UNFCCC: current practices and opportunities for improvement

This report provides an overview of current practices, challenges and opportunities in the measurement, reporting and verification (MRV) of livestock greenhouse gas (GHG) emissions and emission reductions by developing countries in the context of the United Nations Framework Convention on Climate Change (UNFCCC). MRV of livestock GHG emissions is relevant because (i) livestock production makes a significant contribution to global GHG emissions; (ii) livestock GHG emissions have been contributing an increasing share of agricultural emissions over time; and (iii) better characterization of livestock GHG emissions can assist policy makers to target and design efforts to mitigate GHG emissions. As national climate change mitigation policies increasingly focus on GHG reduction targets in Nationally Determined Contributions (NDCs), this report assesses the extent to which current MRV practices are able to meet the evolving policy needs. The report describes MRV obligations under the UNFCCC (Chapter 2), current practices in compiling and reporting livestock GHG emissions through national GHG inventories (Chapter 3) and MRV of mitigation actions (Chapter 4), and highlights opportunities for improvement (Chapter 5).This report is also available in:French: http://hdl.handle.net/10568/93125Spanish: http://hdl.handle.net/10568/93127A summary brief is available at: http://hdl.handle.net/10568/80890

In-trap conversion electron spectroscopy

The Penning trap REXTRAP at ISOLDE was used to test the feasibility of in-trap conversion electron spectroscopy. The results of simulations, experiments with solid conversion electron sources as well as first on-line and tests with trapped radioactive ions are presented. In addition to obtaining high-resolution spectroscopic data, the detection of conversion electrons was found to be a useful tool for the diagnostics of the trap operation. The tests proved the feasibility of in-trap spectroscopy but also revealed some potential problems to be addressed in the future

Capturing the Dynamics of Ti Diffusion Across Ti _x W _1−x /Cu Heterostructures using X‐Ray Photoelectron Spectroscopy

Interdiffusion phenomena between adjacent materials are highly prevalent in semiconductor device architectures and can present a major reliability challenge for the industry. To fully capture these phenomena, experimental approaches must go beyond static and post-mortem studies to include in situ and in-operando setups. Here, soft and hard X-ray photoelectron spectroscopy (SXPS and HAXPES) is used to monitor diffusion in real-time across a proxy device. The device consists of a Si/SiO2/TixW1−x(300 nm)/Cu(25 nm) thin film material stack, with the TixW1−x film (x = 0.054, 0.115, 0.148) acting as a diffusion barrier between Si and Cu. The interdiffusion is monitored through the continuous collection of spectra whilst in situ annealing to 673 K. Ti within the TiW is found to be highly mobile during annealing, diffusing out of the barrier and accumulating at the Cu surface. Increasing the Ti concentration within the TixW1−x film increases the quantity of accumulated Ti, and Ti is first detected at the Cu surface at temperatures as low as 550 K. Surprisingly, at low Ti concentrations (x = 0.054), W is also mobile and diffuses alongside Ti. By monitoring the Ti 1s core level with HAXPES, the surface-accumulated Ti was observed to undergo oxidation even under ultra-high vacuum conditions, highlighting the reactivity of Ti in this system. These results provide crucial evidence for the importance of diffusion barrier composition on their efficacy during device application, delivering insights into the mechanisms underlying their effectiveness and limitations

Zero-order filter for diffractive focusing of de Broglie matter waves

The manipulation of neutral atoms and molecules via their de Broglie wave properties, also referred to as de Broglie matter wave optics, is relevant for several fields ranging from fundamental quantum mechanics tests and quantum metrology to measurements of interaction potentials and new imaging techniques. However, there are several challenges. For example, for diffractive focusing elements, the zero-order beam provides a challenge because it decreases the signal contrast. Here we present the experimental realization of a zero-order filter, also referred to as an order-sorting aperture for de Broglie matter wave diffractive focusing elements. The zero-order filter makes it possible to measure even at low beam intensities. We present measurements of zero-order filtered, focused, neutral helium beams generated at source stagnation pressures between 11 and 81 bars. We show that for certain conditions the atom focusing at lower source stagnation pressures (broader velocity distributions) is better than what has previously been predicted. We present simulations with the software ray-tracing simulation package mcstas using a realistic helium source configuration, which gives very good agreement with our measurements

Fast resolution change in neutral helium atom microscopy

In neutral helium atom microscopy, a beam of atoms is scanned across a surface. Though still in its infancy, neutral helium microscopy has seen a rapid development over the last few years. The inertness and low energy of the helium atoms (less than 0.1 eV) combined with a very large depth of field and the fact that the helium atoms do not penetrate any solid material at low energies open the possibility for a non-destructive instrument that can measure topology on the nanoscale even on fragile and insulating surfaces. The resolution is determined by the beam spot size on the sample. Fast resolution change is an attractive property of a microscope because it allows different aspects of a sample to be investigated and makes it easier to identify specific features. However up till now it has not been possible to change the resolution of a helium microscope without breaking the vacuum and changing parts of the atom source. Here we present a modified source design, which allows fast, step wise resolution change. The basic design idea is to insert a moveable holder with a series of collimating apertures in front of the source, thus changing the effective source size of the beam and thereby the spot size on the surface and thus the microscope resolution. We demonstrate a design with 3 resolution steps. The number of resolution steps can easily be extended.publishedVersio