Transparent switchboard

A tin oxide coating is formed on a plate of glass and the coating is then etched away from the glass in thin lines to form separate electrical conductors which extend to one end of the plate and connect to either a vertical (column) or horizontal (row) position sensing SCR circuit. A thin transparent insulating coating is formed over the oxide layer except at selected touch points which are positioned in a matrix pattern of vertical columns and horizontal rows. Touching one of these points with a finger bridges the thin line between adjacent conductors to activate trigger circuits in the particular row and column sensing circuits associated with the point touched. The row and column sensing circuits are similar and are powered with a low frequency, ac voltage source. The source for the row circuits is 180 out of phase with the source for the column circuits so that one circuit acts as ground for the other during half of the supply voltage cycle. The signals from the sensing circuits are input to a logic circuit which determines the presence of a valid touch, stores a binary matrix number associated with the touched point, signals a computer of the presence of a stored number and prevents storage of a new number before receiving an enable signal from the computer

A wind tunnel investigation of the shape of uncharged raindrops in the presence of an external, electric field

Results of a wind tunnel experiment in which electrically uncharged water drops of 500 to 3000 microns equivalent radius are freely suspended in the vertical air stream of the UCLA cloud tunnel are presented. During this suspension the drops were exposed to external vertical electric fields of 500 to 8,000 volts/cm. The change in drop shape with drop size and electric field strength was noted and is discussed in the light of theoretical work cited in the literature which unfortunately does not take into account the effects of air flow past the drop. The wind tunnel study is documented by stills from a 16 mm film record that demonstrates the shape of water drops in response to both hydrodynamic and electric forces

Study of high voltage solar array configurations with integrated power control electronics

Solar array electrical configurations for voltage regulatio

3D simulations of self-propelled, reconstructed jellyfish using vortex methods

We present simulations of the vortex dynamics associated with the self-propelled motion of jellyfish. The geometry is obtained from image segmentation of video recordings from live jellyfish. The numerical simulations are performed using three-dimensional viscous, vortex particle methods with Brinkman penalization to impose the kinematics of the jellyfish motion. We study two types of strokes recorded in the experiment1. The first type (stroke A) produces two vortex rings during the stroke: one outside the bell during the power stroke and one inside the bell during the recovery stroke. The second type (stroke B) produces three vortex rings: one ring during the power stroke and two vortex rings during the recovery stroke. Both strokes propel the jellyfish, with stroke B producing the highest velocity. The speed of the jellyfish scales with the square root of the Reynolds number. The simulations are visualized in a fluid dynamics video.Comment: 1 page, 1 figur

Single wall carbon nanotube double quantum dot

We report on two top-gate defined, coupled quantum dots in a semiconducting single wall carbon nanotube, constituting a tunable double quantum dot system. The single wall carbon nanotubes are contacted by titanium electrodes, and gated by three narrow top-gate electrodes as well as a back-gate. We show that a bias spectroscopy plot on just one of the two quantum dots can be used to extract the addition energy of both quantum dots. Furthermore, honeycomb charge stability diagrams are analyzed by an electrostatic capacitor model that includes cross capacitances, and we extract the coupling energy of the double quantum dot.Comment: Published in Applied Physics Letters 4 December 2006. http://link.aip.org/link/?APL/89/23211

Critical Current 0-π\pi Transition in Designed Josephson Quantum Dot Junctions

We report on quantum dot based Josephson junctions designed specifically for measuring the supercurrent. From high-accuracy fitting of the current-voltage characteristics we determine the full magnitude of the supercurrent (critical current). Strong gate modulation of the critical current is observed through several consecutive Coulomb blockade oscillations. The critical current crosses zero close to, but not at, resonance due to the so-called 0-$\pi$ transition in agreement with a simple theoretical model.Comment: 5 pages, 4 figures, (Supplementary information available at http://www.fys.ku.dk/~hij/public/nl_supp.pdf