86 research outputs found

    Non destructive examination of composite structures using dielectric examination

    Get PDF
    Dielectric measurements are widely used in the laboratory to probe the dynamics of molecules, particularly the dynamics of polymer molecules. The dielectric technique exploits the fact that many molecules, although electrically neutral posses an asymmetric distribution of charges which can be approximated to an electric dipole. The (usually thermal) motion of the molecule can be detected by the interaction of this dipole with a time varying electric field. The great advantage of the technique is that no transducers or sensors are required; the direct application of an electric field produces a directly measurable electric response over a frequency range of MHz to GHz. This paper discusses the practical application of dielectric measurements to composite structures and the information that can be obtained on the state of the polymer in polymer composite matrix materials

    Performance of periodic piezoelectric composite arrays incorporating a passive phase exhibiting anisotropic properties

    Get PDF
    This paper explores the minimisation of interelement cross talk in 1-D and 2-D periodic composite array structures through the incorporation of a passive phase exhibiting anisotropic elastic properties. Initially the PZFlex finite element code was used to monitor array aperture response as a function of material properties. It is shown that in array structures comprising passive polymer materials possessing low longitudinal loss and high shear loss, inter-element mechanical cross talk is reduced, without a concomitant reduction in element sensitivity. A number of polymer materials with the desired properties were synthesised and their elastic character confirmed through a program of materials characterisation. Finally, a range of experimental devices exhibiting improved directional response, as a result of a significant reduction in interelement cross talk, are presented and the predicted array characteristics are shown to compare favourably in each case

    An inverse problem of reconstructing the electrical and geometrical parameters characterising airframe structures and connector interfaces

    Get PDF
    This article is concerned with the detection of environmental ageing in adhesively bonded structures used in the aircraft industry. Using a transmission line approach a forward model for the reflection coefficients is constructed and is shown to have an analytic solution in the case of constant permeability and permittivity. The inverse problem is analysed to determine necessary conditions for a unique recovery. The main thrust of this article then involves modelling the connector and then experimental rigs are built for the case of the air-filled line to enable the connector parameters to be identified and the inverse solver to be tested. Some results are also displayed for the dielectric-filled line

    The chemical compatibility of thermoplastic hose used in umbilicals

    Get PDF
    The effects of solvents and temperature on thermoplastic hose for umbilical service are reported in this paper. Accelerated ageing tests were undertaken and analysed by gravimetric, mechanical and calorimetric measurements. Water and methanol were found to cause physical degradation of the polymer, mainly at high temperatures, whereas xylene caused chemical degradation, which increased with increasing temperature. The activation energy for the alpha-process within polyethylene (PE) was found to be 96.3 kJ mol(-1) for un-aged PE and increased to 106.2 kJ moll after 64 days of ageing in water at 100degreesC. The changes in activation energy will be used to make a life-time prediction of umbilical line

    Experimental assessment of periodic piezoelectric composite arrays incorporating an anisotropic passive phase

    Get PDF
    This paper discusses the experimental assessment of a number of piezoelectric composite array structures incorporating a novel passive phase exhibiting anisotropic elastic properties. The passive polymer phase has been designed to limit inter-element crosstalk by attenuating lateral propagation across the array aperture. A selection of water coupled linear array coupons, operating with a nominal 400 kHz fundamental thickness mode frequency, has been prepared comprising the novel anisotropic passive phase. As a control, comparisons are made to similarly configured devices employing isotropic filler materials. Scanning laser vibrometry and measurements of electrical impedance characteristic on the array substrate demonstrate that the fundamental thickness mode of the devices configured with anisotropic polymer fillers is not contaminated by parasitic modes of vibration. The reasons for this are explained by considering the dispersion characteristics of the substrate. Water coupled hydrophone measurements of array element directivity; transmit voltage response and subsequently efficiency calculations illustrate that the observed reduction in mechanical cross talk has not been achieved at the expense of element sensitivity. Finally, comparisons between the experimental data and the PZFlex derived array responses are made, with good corroboration demonstrate

    Theoretical modelling of frequency dependent elastic loss in composite piezoelectric transducers

    Get PDF
    The large number of degrees of freedom in the design of piezoelectric transducers requires a theoretical model that is computationally efficient so that a large number of iterations can be performed in the design optimisation. The materials used are often lossy, and indeed loss can be used to enhance the operational characteristics of these designs. Motivated by these needs, this paper extends the one-dimensional linear systems model to incorporate frequency dependent elastic loss. The reception sensitivity, electrical impedance and electromechanical coupling coefficient of a 1-3 composite transducer, with frequency dependent loss in the polymer filler, are investigated. By plotting these operating characteristics as a function of the volume fraction of piezoelectric ceramic an optimum design is obtained. A device with a non-standard, high shear attenuation polymer is also simulated and this leads to an increase in the electromechanical coupling coefficient. A comparison with finite element simulations is then performed. This shows that the two methods are in reasonable agreement in their electrical impedance profiles in all the cases considered. The plots are almost identical away from the main resonant peak where the frequency location of the peaks are comparable but there is in some cases a 20% discrepancy in the magnitude of the peak value and in its bandwidth. The finite element model also shows that the use of a high shear attenuation polymer filler damps out the unwanted, low frequency modes whilst maintaining a reasonable impedance magnitude

    A theoretical analysis of a piezoelectric ultrasound device with an active matching layer

    Get PDF
    This paper investigates the use of magnetically active materials in the matching layer of a piezoelectric transducer. This then allows the performance of the device to be dynamically altered by applying an external field. The effect that this new matching layer has on the performance of a typical device is theoretically investigated here. It transpires that the additional flexibility of an active matching layer can be used to maintain the efficiency of the device as the external load is varied

    Tensile testing of cellulose based natural fibers for structural composite applications

    Get PDF
    A series of tensile tests were conducted on a Lloyd LRX tensile testing machine for numerous natural fibers deemed potential candidates for development in composite applications. The tensile tests were conducted on the fibers jute, kenaf, flax, abaca, sisal, hemp, and coir for samples exposed to moisture conditions of (1) room temperature and humidity, (2) 65% moisture content, (3) 90% moisture content, and (4) soaked fiber. These seven fibers were then tested for the four conditions and the mechanical properties of tensile strength, tensile strain to failure, and Young's modulus were calculated for the results. These results were then compared and verified with those from the literature, with some of the fibers showing distinctly promising potential. Additionally, a study on the effect of alkalization using 3% NaOH solution was carried out on flax, kenaf, abaca, and sisal to observe impact that this common fiber pre-treatment process has on fiber mechanical properties. The result of the investigation indicated that over treatment of natural fibers using NaOH could have a negative effect on the base fiber properties. It is consequently apparent that a treatment time of less than 10 min is sufficient to remove hemicelluloses and to give the optimum effect
    corecore