Bond formation at polycarbonate | X interfaces (X = Al2_2O3_3, TiO2_2, TiAlO2_2) studied by theory and experiments

Interfacial bond formation during sputter deposition of metal oxide thin films onto polycarbonate (PC) is investigated by ab initio molecular dynamics simulations and X-ray photoelectron spectroscopy (XPS) analysis of PC | X interfaces (X = Al$_2$O$_3$, TiO$_2$, TiAlO$_2$). Generally, the predicted bond formation is consistent with the experimental data. For all three interfaces, the majority of bonds identified by XPS are (C-O)-metal bonds, whereas C-metal bonds are the minority. Compared to the PC | Al$_2$O$_3$ interface, the PC | TiO$_2$ and PC | TiAlO$_2$ interfaces exhibit a reduction in the measured interfacial bond density by ~ 75 and ~ 65%, respectively. Multiplying the predicted bond strength with the corresponding experimentally determined interfacial bond density shows that Al$_2$O$_3$ exhibits the strongest interface with PC, while TiO$_2$ and TiAlO$_2$ exhibit ~ 70 and ~ 60% weaker interfaces, respectively. This can be understood by considering the complex interplay between the metal oxide composition, the bond strength as well as the population of bonds that are formed across the interface

Valence electron concentration- and N vacancy-induced elasticity in cubic early transition metal nitrides

Motivated by frequently reported deviations from stoichiometry in cubic transition metal nitride (TMNx) thin films, the effect of N-vacancy concentration on the elastic properties of cubic TiNx, ZrNx, VNx, NbNx, and MoNx (0.72<x<1.00) is systematically studied by density functional theory (DFT) calculations. The predictions are validated experimentally for VNx (0.77<x<0.97). The DFT results indicate that the elastic behavior of the TMNx depends on both the N-vacancy concentration and the valence electron concentration (VEC) of the transition metal: While TiNx and ZrNx exhibit vacancy-induced reductions in elastic modulus, VNx and NbNx show an increase. These trends can be rationalized by considering vacancy-induced changes in elastic anisotropy and bonding. While introduction of N-vacancies in TiNx results in a significant reduction of elastic modulus along all directions and a lower average bond strength of Ti-N, the vacancy-induced reduction in [001] direction of VNx is overcompensated by the higher stiffness along [011] and [111] directions, resulting in a higher average bond strength of V-N. To validate the predicted vacancy-induced changes in elasticity experimentally, close-to-single-crystal VNx (0.77<x<0.97) are grown on MgO(001) substrates. As the N-content is reduced, the relaxed lattice parameter a0, as probed by X-ray diffraction, decreases from 4.128 A to 4.096 A. This reduction in lattice parameter is accompanied by an anomalous 11% increase in elastic modulus, as determined by nanoindentation. As the experimental data agree with the predictions, the elasticity enhancement in VNx upon N-vacancy formation can be understood based on the concomitant changes in elastic anisotropy and bonding.Comment: 30 pages, 8 figures in the manuscript, 1 figure in supplementary material

Large-area deposition of protective (Ti,Al)N coatings onto polycarbonate

Polycarbonate (PC) and protective (Ti,Al)N coatings exhibit extremely different material properties, specifically crystal structure, thermal stability, elastic and plastic behavior as well as thermal expansion coefficients. These differences present formidable challenges for the deposition process development as low-temperature synthesis routes have to be explored to avoid a thermal overload of the polymer substrate. Here, a large-area sputtering process is developed to address the challenges by systematically adjusting target peak power density and duty cycle. Adhering (Ti,Al)N coatings with a critical residual tensile stress of 2.2 +/- 0.2 GPa are obtained in the pulsed direct current magnetron sputtering range, whereas depositions at higher target peak power densities, realized by high power pulsed magnetron sputtering, lead to stress-induced adhesive and/or cohesive failure. The stress-optimized (Ti,Al)N coatings deposited onto PC with a target peak power density of 0.036 kW cm-2 and a duty cycle of 5.3% were investigated by cross-cut test confirming adhesion. By investigating the bond formation at the PC | (Ti,Al)N interface, mostly interfacial CNx bonds and a small fraction of (C-O)-(Ti,Al) bonds are identified by X-ray photoelectron spectroscopy, indicating reactions at the hydrocarbon and the carbonate groups during deposition. Nanoindentation reveals an elastic modulus of 296 +/- 18 GPa for the (Ti,Al)N coating, while a Ti-Al-O layer is formed during electrochemical impedance spectroscopy in a borate buffer solution, indicating protective passivation. This work demonstrates that the challenge posed by the extremely different material properties at the interface of soft polymer substrates and hard coatings can be addressed by systematical variation of the pulsing parameters to reduce the residual film stress

Boron Concentration Induced Co-Ta-B Composite Formation Observed in the Transition from Metallic to Covalent Glasses

Due to their unique property combination of high strength and toughness, metallic glasses are promising materials for structural applications. As the behaviour of metallic glasses depends on the electronic structure which in turn is defined by chemical composition, we systematically investigate the influence of B concentration on glass transition, topology, magnetism, and bonding for B concentrations x = 2 to 92 at.% in the (Co6.8 +/- 3.9Ta)(100-x)B-x system. From an electronic structure and coordination point of view, the B concentration range is divided into three regions: Below 39 +/- 5 at.% B, the material is a metallic glass due to the dominance of metallic bonds. Above 69 +/- 6 at.%, the presence of an icosahedra-like B network is observed. As the B concentration is increased above 39 +/- 5 at.%, the B network evolves while the metallic coordination of the material decreases until the B concentration of 67 +/- 5 at.% is reached. Hence, a composite is formed. It is evident that, based on the B concentration, the ratio of metallic bonding to icosahedral bonding in the composite can be controlled. It is proposed that, by tuning the coordination in the composite region, glassy materials with defined plasticity and processability can be designed

Crystallite size-dependent metastable phase formation of TiAlN coatings

Abstract It is well known that surface energy differences thermodynamically stabilize nanocrystalline γ-Al2O3 over α-Al2O3. Here, through correlative ab initio calculations and advanced material characterization at the nanometer scale, we demonstrate that the metastable phase formation of nanocrystalline TiAlN, an industrial benchmark coating material, is crystallite size-dependent. By relating calculated surface and volume energy contributions to the total energy, we predict the chemical composition-dependent phase boundary between the two metastable solid solution phases of cubic and wurzite Ti1−xAlxN. This phase boundary is characterized by the critical crystallite size d critical . Crystallite size-dependent phase stability predictions are in very good agreement with experimental phase formation data where x was varied by utilizing combinatorial vapor phase condensation. The wide range of critical Al solubilities for metastable cubic Ti1−xAlxN from x max = 0.4 to 0.9 reported in literature and the sobering disagreement thereof with DFT predictions can at least in part be rationalized based on the here identified crystallite size-dependent metastable phase formation. Furthermore, it is evident that predictions of critical Al solubilities in metastable cubic TiAlN are flawed, if the previously overlooked surface energy contribution to the total energy is not considered

Effect of Si on the hydrogen-based direct reduction of Fe2O3 studied by XPS of sputter-deposited thin-film model systems

Understanding the effect of gangue elements is of critical importance to optimize the efficiency of hydrogen -based direct reduction (HyDR) of iron ore, as one of the key steps towards climate-neutral steel production. Here, we demonstrate on the example of Si-doped Fe2O3, how thin films can be effectively utilized as a model system to facilitate systematic investigation of the solid-state reduction behavior. In-vacuo X-ray photoelectron spectroscopy (XPS) is used to probe the reduction kinetics by analyzing the chemical state of iron oxide thin films before and after annealing at 700 degrees C in an Ar+5%H2 atmosphere. It is demonstrated that even low Si concen-trations of 3.7 at.% inhibit the HyDR of Fe2O3 by the formation of a SiOx-enriched reduction barrier in the surface-near region

Valence electron concentration- and N vacancy-induced elasticity in cubic early transition metal nitrides

Motivated by frequently reported deviations from stoichiometry in cubic transition metal nitride (TMNx) thin films, the effect of N-vacancy concentration on the elastic properties of cubic TiNx, ZrNx, VNx, NbNx, and MoNx (0.72 &amp; LE; x &amp; LE; 1.00) is systematically studied by density functional theory (DFT) calculations. The predictions are validated experimentally for VNx (0.77 &amp; LE; x &amp; LE; 0.97). The DFT results indicate that the elastic behavior of the TMNx depends on both the N-vacancy concentration and the valence electron concentration (VEC) of the transition metal: While TiNx and ZrNx exhibit vacancy-induced reductions in elastic modulus, VNx and NbNx show an increase. These trends can be rationalized by considering vacancy-induced changes in elastic anisotropy and bonding. While introduction of N-vacancies in TiNx results in a significant reduction of elastic modulus along all directions and a lower average bond strength of Ti-N, the vacancy-induced reduction in [001] direction of VNx is overcompensated by the higher stiffness along [011] and [111] directions, resulting in a higher average bond strength of V-N. To validate the predicted vacancy-induced changes in elasticity experimentally, close-to-singlecrystal VNx (0.77 &amp; LE; x &amp; LE; 0.97) are grown on MgO(001) substrates. As the N-content is reduced, the relaxed lattice parameter a0, as probed by X-ray diffraction, decreases from 4.128 &amp; ANGS; to 4.096 &amp; ANGS;. This reduction in lattice parameter is accompanied by an anomalous 11% increase in elastic modulus, as determined by nanoindentation. As the experimental data agree with the predictions, the elasticity enhancement in VNx upon N-vacancy formation can be understood based on the concomitant changes in elastic anisotropy and bonding