36,150 research outputs found
Tool for installing or extracting small bulbs in limited-access spaces
Installing and extracting component of tool is plastic tubing with inside diameter which provides snug fit over bulb. Other components, which provide sturdiness and ease of operation, consist of metal tube, with collar near one end, and plunger, with knob on one end and Teflon tip on the other
Relation Between Einstein And Quantum Field Equations
We show that there exists a choice of scalar field modes, such that the
evolution of the quantum field in the zero-mass and large-mass limits is
consistent with the Einstein equations for the background geometry. This choice
of modes is also consistent with zero production of these particles and thus
corresponds to a preferred vacuum state preserved by the evolution. In the
zero-mass limit, we find that the quantum field equation implies the Einstein
equation for the scale factor of a radiation-dominated universe; in the
large-mass case, it implies the corresponding Einstein equation for a
matter-dominated universe. Conversely, if the classical radiation-dominated or
matter-dominated Einstein equations hold, there is no production of scalar
particles in the zero and large mass limits, respectively. The suppression of
particle production in the large mass limit is over and above the expected
suppression at large mass. Our results hold for a certain class of conformally
ultrastatic background geometries and therefore generalize previous results by
one of us for spatially flat Robertson-Walker background geometries. In these
geometries, we find that the temporal part of the graviton equations reduces to
the temporal equation for a massless minimally coupled scalar field, and
therefore the results for massless particle production hold also for gravitons.
Within the class of modes we study, we also find that the requirement of zero
production of massless scalar particles is not consistent with a non-zero
cosmological constant. Possible implications are discussed.Comment: Latex, 24 pages. Minor changes in text from original versio
Design considerations and test facilities for accelerated radiation effects testing
Test design parameters for accelerated dose rate radiation effects tests for spacecraft parts and subsystems used in long term mission (years) are detailed. A facility for use in long term accelerated and unaccelerated testing is described
New Structure In The Shapley Supercluster
We present new radial velocities for 189 galaxies in a 91 sq. deg region of
the Shapley supercluster measured with the FLAIR-II spectrograph on the UK
Schmidt Telescope. The data reveal two sheets of galaxies linking the major
concentrations of the supercluster. The supercluster is not flattened in
Declination as was suggested previously and it may be at least 30 percent
larger than previously thought with a correspondingly larger contribution to
the motion of the Local Group.Comment: LaTex: 2 pages, 1 figure, includes conf_iap.sty style file. To appear
in proceedings of The 14th IAP Colloquium: Wide Field Surveys in Cosmology,
held in Paris, 1998 May 26--30, eds. S.Colombi, Y.Mellie
Jupiters radiation belts and their effects on spacecraft
The effects of electron and proton radiation on spacecraft which will operate in the trapped radiation belts of the planet Jupiter are described, and the techniques and results of the testing and simulation used in the radiation effects program are discussed. Available data from the Pioneer 10 encounter of Jupiter are compared with pre-encounter models of the Jupiter radiation belts. The implications that the measured Jovian radiation belts have for future missions are considered
Design of a Broadband Amplifier for High Speed Applications
This paper provides comprehensive insight into the design approach followed for an amplifier dedicated to high speed base band signals. To demonstrate the methodology, an amplifier consisting of nine PHEMT cascode cells within a distributed amplifier topology was designed. The resulting frequency response is 40 GHz at the 3-dB point, and the output voltage for a 43 Gbps eye diagram is 7.3 Vpp at the chip terminal
Very high two-dimensional hole gas mobilities in strained silicon germanium
We report on the growth by solid source MBE and characterization of remote doped Si/SiGe/Si two-dimensional hole gas structures. It has been found that by reducing the Ge composition to <=13% and limiting the thickness of the alloy layer, growth temperatures can be increased up to 950 °C for these structures while maintaining good structural integrity and planar interfaces. Record mobilities of 19 820 cm2 V−1 s−1 at 7 K were obtained in normal structures. Our calculations suggest that alloy scattering is not important in these structures and that interface roughness and interface charge scattering limit the low temperature mobilities
Elastohydrodynamic film thickness formula based on X-ray measurements with a synthetic paraffinic oil
An empirical elastohydrodynamic film thickness formula for heavily loaded contacts based upon X-ray film thickness measurements made with a synthetic paraffinic oil is presented. The deduced relation was found to adequately reflect the high load dependence exhibited by the measured minimum film thickness data at high Hertizian contact stresses, that is, above 1.04 x 10 to the ninth N/sq m (150,000 psi). Comparisons were made with the numerical results from a theoretical isothermal film thickness formula. The effects of changes in contact geometry, material, and lubricant properties on the form of the empirical model are also discussed
Corrosion of simulated bearing components of three bearing steels in the presence of chloride-contaminated lubricant
Corrosion tests were run with AISI 52100, AISI M-50 and AMS 5794 under conditions that simulate the crevice corrosion found in aircraft ball and roller bearings rejected at overhaul for corrosion. Test specimens were fabricated that simulated the contacts of balls or rollers and the raceways. Corrosion cells were assembled in the presence of a lubricant contaminated with water and chloride ions. The cell was then thermally cycled between 339 K (150 F) and 276 K (37 F). The corrosion observed after 14 cycles was that of crevice and pitting corrosion typically found in aircraft bearings. AMS 5749 showed a very slight amount of corrosion. No appreciable differences were noted between AISI 52100 and AISI M-50, but both showed much greater corrosion than AMS 5749. The corrosion pits observed in AISI M-50 appeared to be fewer in number but generally deeper and larger than in AISI 52100
Correlation of elastohydrodynamic film thickness measurements for fluorocarbon type 2 ester, and polyphenyl ether lubricants
A minimum films thickness correlation applicable to heavily loaded elastohydrodynamic (EHD) contacts was formulated from experimental data obtained by an X-ray transmission technique. The correlation, based on data generated with fluorocarbon, type II ester, and polyphenyl ether lubricants, extends a previous analysis developed from data for a synthetic paraffinic oil. The resulting correlation represents the data of the four lubricants reasonably well over a large range of operating conditions. Contained within the derived relation is a factor to account for the high-load dependence displayed by the measurements beyond that which is provided for by the theory. Thermal corrections applied to a commonly used film thickness formula showed little improvement to the general disagreement that exists between theory and test. Choice of contact geometry and material are judged to have a relatively mild influence on the form of the semiempirical model
- …