513 research outputs found
Sound transmission testing of polymer compounds
This is the post-print version of the final paper published in Polymer Testing. The published article is available from the link below. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. Copyright @ 2012 Elsevier Ltd.Acoustic properties of polymer compounds are an important consideration for many applications. Currently, there are standard test methods for the determination of these properties. There is, however, no standard for the equipment used in these tests, only a specification for the test conditions. The objective of this work was to evaluate the operation and performance of a bench top laboratory sound testing system for its potential as a simple cost effective method for the initial evaluation of materials that require specific acoustic properties. The work was limited to an investigation of the property of sound transmission loss (STL). A study of the effect of the mounting conditions for the samples on the STL was carried out. Following this, a series of polymer and polymer composite samples was tested. The results presented demonstrate the potential for the testing system as an effective standard test method for the acoustic properties of polymer composites and other materials.Technology Strategy Board, U
A Computational Model for Continuous Cooling of Injection Moulding Processes
This paper discusses the approaches and techniques used to build a realistic numerical model to analyse the cooling phase of the injection moulding process. The procedures employed to select an appropriate mesh and the boundary and initial conditions for the problem are discussed and justified. The final model is validated using direct comparisons with experimental results generated in an earlier study. The model is shown to be a useful tool for further studies aimed at optimising the cooling phase of the injection moulding process.
Using the numerical model provides additional information relating to changes in conditions throughout the process, which otherwise could not be deduced or assessed experimentally. These results, and other benefits related to the use of the model, are also discussed in the paper
Development of a species-specific coproantigen ELISA for human taenia solium taeniasis
Taenia solium causes human neurocysticercosis and is endemic in underdeveloped countries where backyard pig keeping is common. Microscopic fecal diagnostic methods for human T. solium taeniasis are not very sensitive, and Taenia saginata and Taenia solium eggs are indistinguishable under the light microscope. Coproantigen (CoAg) ELISA methods are very sensitive, but currently only genus (Taenia) specific. This paper describes the development of a highly species-specific coproantigen ELISA test to detect T. solium intestinal taeniasis. Sensitivity was maintained using a capture antibody of rabbit IgG against T. solium adult whole worm somatic extract, whereas species specificity was achieved by utilization of an enzyme-conjugated rabbit IgG against T. solium adult excretory-secretory (ES) antigen. A known panel of positive and negative human fecal samples was tested with this hybrid sandwich ELISA. The ELISA test gave 100% specificity and 96.4% sensitivity for T. solium tapeworm carriers (N = 28), with a J index of 0.96. This simple ELISA incorporating anti-adult somatic and anti-adult ES antibodies provides the first potentially species-specific coproantigen test for human T. solium taeniasis
Optimisation of Continuous and Pulsed Cooling in Injection Moulding Processes
The concept of pulsed cooling in injection moulding involves cycling the flow of coolant in order that cooling only takes place as and when it is required, as opposed to continuous cooling, where the coolant in run through the channels throughout the entire process. It is claimed that using the pulsed cooling method, with reduced temperature coolants, may reduce cycle times and overall energy consumption for the injection moulding process, when compared with continuous cooling. It is also suggested that this is not at the expense of component integrity since common defects such as warpage, which could come about due to non-uniform cooling of the component, or impedance of flow of the polymer into the mould cavity during injection, do not normally appear.
The study described in this paper uses a previously validated numerical model in order to optimise the cooling phase of the injection moulding process, for both continuous and pulsed cooling, in order to assess the advantages and disadvantages of each method, with respect to cycle times. In addition, the optimisations were carried out with a view to improving cycle times experimentally, taking into consideration the findings of the study
Human and Canine Echinococcosis Infection in Informal, Unlicensed Abattoirs in Lima, Peru
Echinococcus granulosus infections are a major public health problem in livestock-raising regions around the world. The life cycle of this tapeworm is sustained between dogs (definitive host, canine echinococcosis), and herbivores (intermediary host, cystic hydatid disease). Humans may also develop cystic hydatid disease. Echinococcosis is endemic in rural areas of Peru; nevertheless, its presence or the extension of the problem in urban areas is basically unknown. Migration into Lima, an 8-million habitant's metropolis, creates peripheral areas where animals brought from endemic areas are slaughtered without veterinary supervision. We identified eight informal, unlicensed abattoirs in a peripheral district of Lima and performed a cross-sectional study in to assess the prevalence of canine echinococcosis, evaluated by coproELISA followed by PCR evaluation and arecoline purge. Eight of 22 dogs (36%) were positive to coproELISA, and four (18%) were confirmed to be infected with E. granulosus tapeworms either by PCR or direct observation (purge). Later evaluation of the human population living in these abattoirs using abdominal ultrasound, chest X-rays and serology, found 3 out of 32 (9.3%) subjects with echinococcal cysts in the liver (two viable, one calcified), one of whom had also lung involvement and a strongly positive antibody response. Autochthonous transmission of E. granulosus is present in Lima. Informal, unlicensed abattoirs may be sources of infection to neighbouring people in this urban environment
Multi-modal imaging probe for assessing the efficiency of stem cell delivery to orthotopic breast tumours
Stem cells have been utilised as anti-cancer agents due to their ability to home to and integrate within tumours. Methods to augment stem cell homing to tumours are being investigated with the goal of enhancing treatment efficacy. However, it is currently not possible to evaluate both cell localisation and cell viability after engraftment, hindering optimisation of therapy. In this study, luciferase-expressing human adipocyte-derived stem cells (ADSCs) were incubated with Indium-111 radiolabelled iron oxide nanoparticles to produce cells with tri-modal imaging capabilities. ADSCs were administered intravenously (IV) or intracardially (IC) to mice bearing orthotopic breast tumours. Cell fate was monitored using bioluminescence imaging (BLI) as a measure of cell viability, magnetic resonance imaging (MRI) for cell localisation and single photon emission computer tomography (SPECT) for cell quantification. Serial monitoring with multi-modal imaging showed the presence of viable ADSCs within tumours as early as 1-hour post IC injection and the percentage of ADSCs within tumours to be 2-fold higher after IC than IV. Finally, histological analysis was used to validate engraftment of ADSC within tumour tissue. These findings demonstrate that multi-modal imaging can be used to evaluate the efficiency of stem cell delivery to tumours and that IC cell administration is more effective for tumour targeting
Elimination of Schistosomiasis Transmission in Zanzibar: Baseline Findings before the Onset of a Randomized Intervention Trial.
Gaining and sustaining control of schistosomiasis and, whenever feasible, achieving local elimination are the year 2020 targets set by the World Health Organization. In Zanzibar, various institutions and stakeholders have joined forces to eliminate urogenital schistosomiasis within 5 years. We report baseline findings before the onset of a randomized intervention trial designed to assess the differential impact of community-based praziquantel administration, snail control, and behavior change interventions. In early 2012, a baseline parasitological survey was conducted in ∼20,000 people from 90 communities in Unguja and Pemba. Risk factors for schistosomiasis were assessed by administering a questionnaire to adults. In selected communities, local knowledge about schistosomiasis transmission and prevention was determined in focus group discussions and in-depths interviews. Intermediate host snails were collected and examined for shedding of cercariae. The baseline Schistosoma haematobium prevalence in school children and adults was 4.3% (range: 0-19.7%) and 2.7% (range: 0-26.5%) in Unguja, and 8.9% (range: 0-31.8%) and 5.5% (range: 0-23.4%) in Pemba, respectively. Heavy infections were detected in 15.1% and 35.6% of the positive school children in Unguja and Pemba, respectively. Males were at higher risk than females (odds ratio (OR): 1.45; 95% confidence interval (CI): 1.03-2.03). Decreasing adult age (OR: 1.04; CI: 1.02-1.06), being born in Pemba (OR: 1.48; CI: 1.02-2.13) or Tanzania (OR: 2.36; CI: 1.16-4.78), and use of freshwater (OR: 2.15; CI: 1.53-3.03) showed higher odds of infection. Community knowledge about schistosomiasis was low. Only few infected Bulinus snails were found. The relatively low S. haematobium prevalence in Zanzibar is a promising starting point for elimination. However, there is a need to improve community knowledge about disease transmission and prevention. Control measures tailored to the local context, placing particular attention to hot-spot areas, high-risk groups, and individuals, will be necessary if elimination is to be achieved
Habitat filtering determines spatial variation of macroinvertebrate community traits in northern headwater streams
Although our knowledge of the spatial distribution of stream organisms has been increasing rapidly in the last decades, there is still little consensus about trait-based variability of macroinvertebrate communities within and between catchments in near-pristine systems. Our aim was to examine the taxonomic and trait based stability vs. variability of stream macroinvertebrates in three high-latitude catchments in Finland. The collected taxa were assigned to unique trait combinations (UTCs) using biological traits. We found that only a single or a highly limited number of taxa formed a single UTC, suggesting a low degree of redundancy. Our analyses revealed significant differences in the environmental conditions of the streams among the three catchments. Linear models, rarefaction curves and beta-diversity measures showed that the catchments differed in both alpha and beta diversity. Taxon- and trait-based multivariate analyses also indicated that the three catchments were significantly different in terms of macroinvertebrate communities. All these findings suggest that habitat filtering, i.e., environmental differences among catchments, determines the variability of macroinvertebrate communities, thereby contributing to the significant biological differences among the catchments. The main implications of our study is that the sensitivity of trait-based analyses to natural environmental variation should be carefully incorporated in the assessment of environmental degradation, and that further studies are needed for a deeper understanding of trait-based community patterns across near-pristine streams
Identification and characterization of a novel non-structural protein of bluetongue virus
Bluetongue virus (BTV) is the causative agent of a major disease of livestock (bluetongue). For over two decades, it has been widely accepted that the 10 segments of the dsRNA genome of BTV encode for 7 structural and 3 non-structural proteins. The non-structural proteins (NS1, NS2, NS3/NS3a) play different key roles during the viral replication cycle. In this study we show that BTV expresses a fourth non-structural protein (that we designated NS4) encoded by an open reading frame in segment 9 overlapping the open reading frame encoding VP6. NS4 is 77–79 amino acid residues in length and highly conserved among several BTV serotypes/strains. NS4 was expressed early post-infection and localized in the nucleoli of BTV infected cells. By reverse genetics, we showed that NS4 is dispensable for BTV replication in vitro, both in mammalian and insect cells, and does not affect viral virulence in murine models of bluetongue infection. Interestingly, NS4 conferred a replication advantage to BTV-8, but not to BTV-1, in cells in an interferon (IFN)-induced antiviral state. However, the BTV-1 NS4 conferred a replication advantage both to a BTV-8 reassortant containing the entire segment 9 of BTV-1 and to a BTV-8 mutant with the NS4 identical to the homologous BTV-1 protein. Collectively, this study suggests that NS4 plays an important role in virus-host interaction and is one of the mechanisms played, at least by BTV-8, to counteract the antiviral response of the host. In addition, the distinct nucleolar localization of NS4, being expressed by a virus that replicates exclusively in the cytoplasm, offers new avenues to investigate the multiple roles played by the nucleolus in the biology of the cell
- …