7,845 research outputs found
Assessment of the operating characteristics of the SSME LOX turbopump pump-end bearing
A bearing/shaft model of the SSME LOX turbopump was developed using the SHABERTH bearing/shaft math modeling computer code. A previously developed bearing/shaft thermal model of the SSME LOX turbopump turbine and bearing was used in conjunction with SHABERTH to evaluate the thermomechanical operating characteristics of the LOX turbopump end bearings. Results show that for the two unmounted diametrical clearances evaluated (4.0 mils and 6.3 mils), the inboard pump end bearing supports about 81% of the isolator load for the small clearance and 77% of the isolator load for the larger clearance. Bearing clearance changes due to thermal effects were 40% for the 4.0 mil diametrical clearance case and 19% for the 6.3 mil clearance case evaluated. The thermal analysis included evaluation of bearing temperatures for a subcooled case and a saturated case. Results indicate that no drastic temperature change occurred between the two cases. Since the rolling element and race surfaces of the subcooled case were at temperatures sufficiently high enough to be vapor blanketed, exceeding saturation temperature at the bearing inlet did not increase surface temperatures greatly
Characterisation of the dynamical quantum state of a zero temperature Bose-Einstein condensate
We describe the quantum state of a Bose-Einstein condensate at zero
temperature. By evaluating the Q-function we show that the ground state of
Bose-Einstein condensate under the Hartree approximation is squeezed. We find
that multimode Schroedinger cat states are generated as the condensate evolves
in a ballistic expansion.Comment: 13 pages, 6 figure
Advanced rocket engine cryogenic turbopump bearing thermal model
A lumped node thermal model was developed representing the Space Shuttle Main Engine (SSME) liquid oxygen (LOX) turbopump turbine end bearings operating in a cryogenically cooled bearing tester. Bearing elements, shaft, carrier, housing, cryogen flow characteristics, friction heat, and fluid viscous energy are included in the model. Heat transfer characteristics for the regimes of forced convection boiling are modeled for liquid oxygen (LOX) and liquid nitrogen (LN2). Large temperature differences between the cryogenic fluid and baring contact surfaces require detailed nodal representation in these areas. Internal loads and friction heat are affected by temperature dependent operating clearances requiring iterations between bearing thermal and mechanical models. Analyses indicate a thermal-mechanical coupling resulting in reduced operating clearances, increased loading and heating which can contribute to premature bearing failure. Contact surfaces operate at temperatures above local saturation resulting in vapor rather than liquid in the contacts, precluding possible liquid film lubrication. Elevated temperatures can reduce lubrication, increase friction, and reduce surface hardness supporting a surface failure mode rather than subsurface fatigue
On Approximating the Number of -cliques in Sublinear Time
We study the problem of approximating the number of -cliques in a graph
when given query access to the graph.
We consider the standard query model for general graphs via (1) degree
queries, (2) neighbor queries and (3) pair queries. Let denote the number
of vertices in the graph, the number of edges, and the number of
-cliques. We design an algorithm that outputs a
-approximation (with high probability) for , whose
expected query complexity and running time are
O\left(\frac{n}{C_k^{1/k}}+\frac{m^{k/2}}{C_k}\right)\poly(\log
n,1/\varepsilon,k).
Hence, the complexity of the algorithm is sublinear in the size of the graph
for . Furthermore, we prove a lower bound showing that
the query complexity of our algorithm is essentially optimal (up to the
dependence on , and ).
The previous results in this vein are by Feige (SICOMP 06) and by Goldreich
and Ron (RSA 08) for edge counting () and by Eden et al. (FOCS 2015) for
triangle counting (). Our result matches the complexities of these
results.
The previous result by Eden et al. hinges on a certain amortization technique
that works only for triangle counting, and does not generalize for larger
cliques. We obtain a general algorithm that works for any by
designing a procedure that samples each -clique incident to a given set
of vertices with approximately equal probability. The primary difficulty is in
finding cliques incident to purely high-degree vertices, since random sampling
within neighbors has a low success probability. This is achieved by an
algorithm that samples uniform random high degree vertices and a careful
tradeoff between estimating cliques incident purely to high-degree vertices and
those that include a low-degree vertex
3-Dimensional Core-Collapse
In this paper, we present the results of 3-dimensional collapse simulations
of rotating stars for a range of stellar progenitors. We find that for the
fastest spinning stars, rotation does indeed modify the convection above the
proto-neutron star, but it is not fast enough to cause core fragmentation.
Similarly, although strong magnetic fields can be produced once the
proto-neutron star cools and contracts, the proto-neutron star is not spinning
fast enough to generate strong magnetic fields quickly after collapse and, for
our simulations, magnetic fields will not dominate the supernova explosion
mechanism. Even so, the resulting pulsars for our fastest rotating models may
emit enough energy to dominate the total explosion energy of the supernova.
However, more recent stellar models predict rotation rates that are much too
slow to affect the explosion, but these models are not sophisticated enough to
determine whether the most recent, or past, stellar rotation rates are most
likely. Thus, we must rely upon observational constraints to determine the true
rotation rates of stellar cores just before collapse. We conclude with a
discussion of the possible constraints on stellar rotation which we can derive
from core-collapse supernovae.Comment: 34 pages (5 of 17 figures missing), For full paper, goto
http://qso.lanl.gov/~clf/papers/rot.ps.gz accepted by Ap
Alarming Rise In People With Allergies
Symptoms range from mild irritation to life threatening attacks Triggers can be something as common as dust or nuts One third of the population has one form or another of allergy
Economic Analysis of a Traveling Gun for Feedyard Dust Suppression
Dust created in feedyards can adversely affect cattle performance. Dust suppression can be accomplished by moistening pen surfaces with traveling gun(s) sprinklers, solid-set sprinklers, and water trucks. This study specifically addresses the fixed and operational costs associated with a traveling gun sprinkler system for various sized feedyards.traveling gun, dust suppression, fixed costs, operational costs, Livestock Production/Industries,
Dreaming Love of You / words by Chas K. Harris
Cover: drawing of a woman surrounded by flowers; Publisher: Chas K. Harris (New York)https://egrove.olemiss.edu/sharris_b/1061/thumbnail.jp
- …