Evaluation of Toughness of High Strength Low Alloy (HSLA) Steels as a Function of Carbon Content

The influence of carbon content on the microstructure and toughness of HSLA steel at room temperature was investigated based on experimental work and literature. It was revealed that increasing the carbon content in from 0.06 to 0.14 wt-% is detrimental to toughness, giving higher impact transition temperature. The deterioration of toughness was correlated to undesired changes in the microstructure, which showed an increase in pearlite volume fraction at the expense of ferrite. At high carbon content, cementite of pearlite was found to grow more rapidly to form continuous plates which act as preferred sites for crack nucleation and propagation. In addition, the lamellar spacing of the pearlite increased as a function of carbon content, which in turn gave worse toughness. The presence of high carbon content and carbide forming elements in the chemical composition was more detrimental to toughness due to the formation of thick carbides around the grain boundaries. These carbides act as a path for crack propagation, which makes it easy for cracks to cohere, leading to intergranular fracture. Keywords - HSLA steel, Carbon, Brittleness, Toughness, Impact Transition Temperature (ITT)

The influence of Widmanstätten ferrite, martensite and grain boundary carbides on the strength and impact behaviour of high Al (0.2%) and Nb containing hot rolled steels

The influence of Al and Nb on the strength and impact behaviour of hot rolled 0.06%C, 1.4%Mn steels has been determined after hot rolling to 15 and 30 mm thick plate. When 0.16%Al was added to the plain C-Mn steel, the impact behaviour significantly improved even though Widmanstätten ferrite (WF) was present. This improvement was due to refinement of the grain boundary carbides and removing the N from solution as AlN. The hot rolled steels all contained WF but when Nb was added more WF formed as well as MA giving poor impact behaviour. Reducing the hardenability from that shown in previous work by decreasing C from 0.1 to 0.06%, Nb from 0.03 to 0.02%, and cooling rate from 33 to 17 K/min had no effect in improving the impact performance of hot rolled Nb steels. To ensure optimum properties not only is it necessary to reduce the hardenability, but WF formation must be discouraged by having a high Ar3. This can only be presently achieved by refining the austenite grain size via control rolling the Nb containing steels; the benefit of adding Al can then, readily be seen. Suggestions are made as to how this might be achieved for hot rolling

Influence of Al content on the corrosion resistance of micro-alloyed hot rolled steel as a function of grain size

High-strength low-alloy steel (HSLA) has been widely used in many applications involving automobiles, aerospace, construction, and oil and gas pipelines due to their enhanced mechanical and chemical properties. One of the most critical elements used to improve these properties is Aluminium. This work will explore the effect of Al content on the corrosion behaviour of hot rolled high-strength low-alloy steel as a function of grain size. The method of investigation employed was weight loss technique. It was obvious that the increase in Al content enhanced corrosion resistance through refinement of grain size obtained through AlN precipitation by pinning grain boundaries and hindering their growth during solidification which was found to be beneficial in reducing corrosion rate

Hot rolled high Al containing steels as a replacement for the control rolled high strength low alloy (HSLA) steels

The extent to which Al and Nb can be used to improve the properties of hot rolled steels has been investigated with the aim of obtaining mechanical properties similar to those given by the more expensive, control rolled or normalised route, eg. API X52 line pipe. Three steels with 0.02%Al, 0.16%Al and 0.16%Al, 0.018%Nb have been examined and their strength and impact behaviour obtained. The 0.16%Al steel had a similar strength to the 0.02%Al containing steel∼300MPa, but better impact behaviour (30-40°C lower 54J, ITT) with an impact transition temperature (ITT) of −90°C which from previous work will be due to a refinement of the grain boundary carbides. The present work shows that the addition of Nb to this high Al containing steel, although beneficial to strength, giving a lower yield strength (LYS) of 385 MPa, close to that given by some of the control rolled steels gives very poor impact behaviour with a 54J ITT of only −20°C. The improvement of strength is mainly a result of precipitation hardening by NbCN with some benefit from grain refinement while the deterioration of impact behaviour might be due to the presence of lower transformation products or coarser carbides. Further work is required to positively clarify the cause of this deterioration and to explore further options in achieving the aim of obtaining a hot rolled steel with strength in the range 350-400MPa and 54J ITT of −50°C

Hot ductility of high Al TWIP steels containing Nb and Nb-V

The hot ductility of B-Ti-Nb-high Al (1.5%Al) containing TWIP steels having Ti/N ratios mainly in excess of 3.4/1 was obtained. After soaking at 1250°C, the tensile specimens were cooled at 12 or 60°C min−1 to the test temperature and then strained to failure at 3 × 10−3 s−1. Ductility was always good (reduction of area >40%), independent of Ti/N ratio or cooling rate. The good ductility is due to B segregation strengthening the grain boundaries and the low S level (0.005%S) limiting the volume fraction of MnS inclusions and restricting AlN precipitation to the matrix. Increasing the cooling rate, higher N levels and Nb resulted in a small improvement in ductility. An addition of V to the Nb-containing steels caused a slight deterioration in the hot ductility

Impacts of Salinity on Soil Properties of Coastal Areas in Bangladesh

Sea level rise is a growing threat for the coastal regions of Bangladesh. It is one of the most densely populated countries of the world where 28% of the population are living in the coastal area. Bangladesh has already been affected by sea level rise through land erosion, salinity intrusion and loss in biodiversity. Saline soil has a detrimental effect upon soil physical and chemical properties. The dominant soil textural classes that occur in the saline areas of these regions are silty clay. In both of the soils pH value of the surface horizon is slightly lower than those of the subsoil and sub stratums. Cation Exchange Capacity (CEC) of all these soils varies from 12.0 to 27.6 meq/100 g soil expressing medium to high status. The organic matter content is medium to high at Asasuni and pretty low at Kalapara. In both areas, nutrient deficiencies of total nitrogen, phosphorous and potassium were quite dominant but sulphur was high. Exchangeable sodium, potassium, calcium and magnesium were in high level. The dominant water soluble cations were Na+, Ca2+, Mg2+ and K+ and anions Cl- and SO4 2-.The amount of accumulated salt was found higher at the surface and decreases with depth

Investigation of corrosion resistance of high-strength low-alloy (HSLA) steel in fresh and salt water for pipeline application

Corrosion behaviour of HSLA steel immersed in fresh and salt water for a four weeks period was investigated by weight loss method at room temperature. The main applications considered for the current work are underground water pipes and the pipeline systems in desalination plants. The corrosion behaviour in the saltwater medium was more severe but the rate was found to drop in the fourth week, presumably due to the formation of a protective passive film on the surface. The combination of ferrite and cementite phases in the microstructure contributed to promoting the corrosion rate due to the initiation of galvanic cells between both phases

The modified BenjaminBona-Mahony equation via the extended generalized Riccati equation mapping method

Abstract The generalized Riccati equation mapping is extended together with the ( ) expansion method and is a powerful mathematical tool for solving nonlinear partial differential equations. In this article, we construct twenty seven new exact traveling wave solutions including solitons and periodic solutions of the modified Benjamin-Bona-Mahony equation by applying the extended generalized Riccati equation mapping method. In this method, implemented as the auxiliary equation, where , r s and p are arbitrary constants and called the generalized Riccati equation. The obtained solutions are described in four different families including the hyperbolic functions, the trigonometric functions and the rational functions. In addition, it is worth mentioning that one of newly obtained solutions is identical for a special case with already published result which validates our other solutions. Mathematics Subject Classification: 35K99, 35P99, 35P05 Keywords: The modified Benjamin-Bona-Mahony equation, the generalized Riccati equation, the ( ) / G G ′ -expansion method, traveling wave solutions, nonlinear evolution equations

The effect of direct thermal method, temperature and time on microstructure of a cast aluminum alloy

The direct thermal method is used for the creation of globular microstructures suitable for semi-solid metal forming. In this paper both simulation and experimental results using direct thermal method are presented. ProCAST® software was used to estimate temperature distribution inside the aluminium billet. In validation work, molten aluminium A356 was poured into metallic copper tube moulds and cooled down to the semi-solid temperature before being quenched in water at room temperature. The effect of pouring temperatures of 630°C, 650°C, 665°C, 680°C and holding times of 45s and 60s on the microstructure of aluminium A356 alloy were investigated. The simulation results showed that the average temperature rate within the copper mould, from initial pouring temperature to just before quenching, was approximately 1°C/s. Examination of the solidified microstructures showed that the microstructure was more spherical when lower pouring temperatures and holding periods were used. From the micrographs it was found that the most globular and smallest structures were achieved at processing parameters of 630°C and 45s