6,273 research outputs found
Tungsten wire/FeCrAlY matrix turbine blade fabrication study
The objective was to establish a viable FRS monotape technology base to fabricate a complex, advanced turbine blade. All elements of monotape fabrication were addressed. A new process for incorporation of the matrix, including bi-alloy matrices, was developed. Bonding, cleaning, cutting, sizing, and forming parameters were established. These monotapes were then used to fabricate a 48 ply solid JT9D-7F 1st stage turbine blade. Core technology was then developed and first a 12 ply and then a 7 ply shell hollow airfoil was fabricated. As the fabrication technology advanced, additional airfoils incorporated further elements of sophistication, by introducing in sequence bonded root blocks, cross-plying, bi-metallic matrix, tip cap, trailing edge slots, and impingement inserts
Tungsten wire-reinforced superalloys for 1093 C (2000 F) turbine blade applications
Various combinations of fiber and matrix materials were fabricated and evaluated for the purpose of selecting a specific combination that exhibited the best overall properties for a turbine blade application. A total of seven matrix alloys, including Hastelloy X, Nimonic 80A, Inconel 600, Inconel 625, IN-102, FeCrA1Y, were investigated reinforced with either 218CS tungsten, or W-Hf-C fibers. Based on preliminary screening studies, FeCrA1Y, Inconel 600 and Inconel 625 matrix composites systems were selected for extended thermal cycle tests and for property evaluations which included stress rupture, impact, and oxidation resistance. Of those investigated, the FeCrA1Y matrix composite system exhibited the best overall properties required for a turbine blade application. The W-Hf-C/FeCrA1Y system was selected for further property evaluation. Tensile strength values of up to 724 MPa (105,000 psi) were obtained for this material at 982 C and 607 MPa at 1093 C
Wave propagation in two-dimensional periodic lattices
International audiencePlane wave propagation in infinite two-dimensional periodic lattices is investigated using Floquet-Bloch principles. Frequency bandgaps and spatial filtering phenomena are examined in four representative planar lattice topologies: hexagonal honeycomb, Kagomé lattice, triangular honeycomb, and the square honeycomb. These topologies exhibit dramatic differences in their long-wavelength deformation properties. Long-wavelength asymptotes to the dispersion curves based on homogenization theory are in good agreement with the numerical results for each of the four lattices. The slenderness ratio of the constituent beams of the lattice (or relative density) has a significant influence on the band structure. The techniques developed in this work can be used to design lattices with a desired band structure. The observed spatial filtering effects due to anisotropy at high frequencies (short wavelengths) of wave propagation are consistent with the lattice symmetries
The Dynamics of Energy Systems and the Logistic Substitution Model. Executive Summary
This is a report on the work done at the International Institute for Applied Systems Analysis in 1976 to 1977 under a grant from Volkswagenwerk Foundation, whose objective was to explore the potential and the mechanisms of logistic analysis to describe the structure and the evolution of energy systems.
Volume One contains the phenomenological part. About 300 cases were examined, some of which are reported in detail. The quality of the logistic description is generally excellent, even for cases extending 150 years into the past and with all the perturbations such a long time span entails, and consequently we thought it appropriate to extend the description into the future and use it for prediction.
This was not really the objective of the grant but 'it naturally arises from the work and provides food for thought. Projections in the current literature appear to be in fact strongly inconsistent with the past, which casts doubts on their realizability, and are even internally inconsistent, which reinforces these doubts.
The fact that numerous "free" choices at the social level lead to very regular overall patterns should perhaps temper the feeling of being caught in a deterministic clockwork.
In Volume Two, devoted to the theoretical work, F. Fleck deals specifically with this problem showing the final regularity derived from a set of stochastic, i.e. "free", decisions. V. Peterka, on the other hand, operates at a more aggregated level, where one can start to speak of economic determinism. He describes a form of fate we are more ready to accept, if only grudgingly.
Our exploration has generated more problems than we have solved; thus the field appears very fertile for future research
Radical Artificial Intelligence: A Postmodern Approach
The dynamic response of end-clamped monolithic beams and sandwich beams has been measured by loading the beams at mid-span using metal foam projectiles. The AISI 304 stainless-steel sandwich beams comprise two identical face sheets and either prismatic Y-frame or corrugated cores. The resistance to shock loading is quantified by the permanent transverse deflection at mid-span of the beams as a function of projectile momentum. The prismatic cores are aligned either longitudinally along the beam length or transversely. It is found that the sandwich beams with a longitudinal core orientation have a higher shock resistance than the monolithic beams of equal mass. In contrast, the performance of the sandwich beams with a transverse core orientation is very similar to that of the monolithic beams. Three-dimensional finite element (FE) simulations are in good agreement with the measured responses. The FE calculations indicate that strain concentrations in the sandwich beams occur at joints within the cores and between the core and face sheets; the level of maximum strain is similar for the Y-frame and corrugated core beams for a given value of projectile momentum. The experimental and FE results taken together reveal that Y-frame and corrugated core sandwich beams of equal mass have similar dynamic performances in terms of rear-face deflection, degree of core compression and level of strain within the beam
Mercury, Methylmercury, and Other Constituents in Sediment and Water from Seasonal and Permanent Wetlands in the Cache Creek Settling Basin and Yolo Bypass, Yolo County, California, 2005−06
This report presents surface water and surface (top 0-2 cm) sediment geochemical data collected during 2005-2006, as part of a larger study of mercury (Hg) dynamics in seasonal and permanently flooded wetland habitats within the lower Sacramento River basin, Yolo County, California. The study was conducted in two phases. Phase I represented reconnaissance sampling and included three locations within the Cache Creek drainage basin; two within the Cache Creek Nature Preserve (CCNP) and one in the Cache Creek Settling Basin (CCSB) within the creek’s main channel near the southeast outlet to the Yolo Bypass. Two additional downstream sites within the Yolo Bypass Wildlife Area (YBWA) were also sampled during Phase I, including one permanently flooded wetland and one seasonally flooded wetland, which had began being flooded only 1–2 days before Phase I sampling.
Results from Phase I include: (a) a negative correlation between total mercury (THg) and the percentage of methylmercury (MeHg) in unfiltered surface water; (b) a positive correlation between sediment THg concentration and sediment organic content; (c) surface water and sediment THg concentrations were highest at the CCSB site; (d) sediment inorganic reactive mercury (Hg(II)R) concentration was positively related to sediment oxidation-reduction potential and negatively related to sediment acid volatile sulfur (AVS) concentration; (e) sediment Hg(II)R concentrations were highest at the two YBWA sites; (f) unfiltered surface water MeHg concentration was highest at the seasonal wetland YBWA site, and sediment MeHg was highest at the permanently flooded YBWA site; (g) a 1,000-fold increase in sediment pore water sulfate concentration was observed in the downstream transect from the CCNP to the YBWA; (h) low sediment pore water sulfide concentrations (μmol/L) across all sites; and (i) iron (Fe) speciation data suggest a higher potential for microbial Fe(III)-reduction in the YBWA compared to the CCSB.
Phase II sampling did not include the original three Cache Creek sites, but instead focused on the original two sites within the YBWA and a similarly paired set of seasonally and permanently flooded wetland sites within the CCSB. Sediment sampling at the YBWA and CCSB occurred approximately 28 days and 52 days, respectively, after the initial flooding of the respective seasonal wetlands, and again towards the end of the seasonal flooding period (end of May 2006). Results from Phase II sampling include: (a) sediment MeHg concentration and the percentage of THg as MeHg (%MeHg) in unfiltered surface waters were generally higher in the YBWA compared to the CCSB; (b) suspended sediment concentration (SCC) in surface water was positively correlated with both THg and MeHg in unfiltered water across all sites, although the relationship between SCC and MeHg differed for the two regions, suggesting local MeHg sources; (c) MeHg concentration in unfiltered surface water was positively correlated to sediment MeHg concentrations across all sites, supporting the suggestion of unique local (sediment) sources of MeHg to the water column; (d) THg concentration in filtered water was positively correlated with both total Fe and dissolved organic carbon (DOC), offering additional support for the role of these constituents in the partitioning of THg between particulate and dissolved phases; (e) flooding of the YBWA seasonal wetland resulted in a rapid and significant (5-fold) rise in sediment MeHg concentration within 3–4 weeks following inundation; and (f) temporal changes in sediment S and Fe speciation suggest that rates of both microbial sulfate reduction and Fe(III)-reduction were significantly higher at YBWA, compared to CCSB, during the period between flooding and drying.
The geochemical data presented in this report indicate that (a) strong spatial and temporal differences in Hg speciation and transformations can occur within the range of wetland habitats found in the lower Sacramento River basin; (b) flooding of seasonal wetlands can be accompanied by a rapid increase in benthic MeHg production and the release of previously formed MeHg (generated during or since the previous flooding season) to the overlying water column; (c) S and Fe chemistry, and associated microbial reduction pathways, play an important role in mediating the speciation and transformation of Hg in these wetland habitats; (d) hydroperiod is a primary forcing function in mediating MeHg production among various wetland types; and (e) MeHg production appears to be more active in the YBWA compared to the CCSB
Is the partial pressure of carbon dioxide in the blood related to the development of retinopathy of prematurity?
AIMS—To determine the role of carbon dioxide in the development of retinopathy of prematurity (ROP).
METHODS—This was a retrospective cohort study of 25 consecutive infants admitted to the neonatal unit with continuously recorded physiological data. The daily mean and standard deviation (SD) of transcutaneous carbon dioxide partial pressure (tcPCO(2)) was compared between infants who had stage 1 or 2 ROP and stage 3 ROP. The time spent hypocarbic (<3 kPa) and/or hypercarbic (>10 kPa and >12 kPa) was also compared between these groups. Intermittent arterial carbon dioxide tension was also measured and compared with the simultaneous tcPCO(2) data.
RESULTS—There were no significant differences in carbon dioxide variability or time spent hypocarbic and/or hypercarbic between the ROP groups on any day. 86% of transcutaneous values were within 1.5 kPa of the simultaneous arterial value.
CONCLUSION—TcPCO(2) measurement can be a very useful management technique. However, in this cohort neither variable blood carbon dioxide tension nor duration of hypercarbia or hypocarbia in the first 2 weeks of life was associated with the development or severity of ROP.

Powder metallurgy bearings for advanced rocket engines
Traditional ingot metallurgy was pushed to the limit for many demanding applications including antifriction bearings. New systems require corrosion resistance, better fatigue resistance, and higher toughness. With conventional processing, increasing the alloying level to achieve corrosion resistance results in a decrease in other properties such as toughness. Advanced powder metallurgy affords a viable solution to this problem. During powder manufacture, the individual particle solidifies very rapidly; as a consequence, the primary carbides are very small and uniformly distributed. When properly consolidated, this uniform structure is preserved while generating a fully dense product. Element tests including rolling contact fatigue, hot hardness, wear, fracture toughness, and corrosion resistance are underway on eleven candidate P/M bearing alloys and results are compared with those for wrought 440C steel, the current SSME bearing material. Several materials which offer the promise of a significant improvement in performance were identified
Lo-fi prototyping to design interactive-tabletop applications for children
Interactive tabletops are an exiting new platform for supporting children's collaboration. With design guidelines and standardized interaction principles still immature, there is a considerable need for iterative prototyping to define the task and interface. Lo-fi prototypes-using cardboard, paper, etc.- are easy to develop, flexible to adjust during design sessions, and intuitive for users to manipulate. Using them can be a valuable step in designing tabletop applications.
In this paper, we detail the design process of two tabletop applications, concentrating on the role of lo-fi prototyping. TransTime is a pattern game for 5-6 year olds to engage how time progresses. OurSpace is a design tool for 7-9 year olds to arrange desks and assign seats for students in their classroom. By comparing the experiences, we arrive at a better understanding of the benefits, challenges, and limits of using lo-fi prototypes to design interactive-tabletop applications for children
Fracture of bio-cemented sands
Bio-chemical reactions enable the production of biomimetic materials such as
sandstones. In the present study, microbiologically-induced calcium carbonate
precipitation (MICP) is used to manufacture laboratory-scale specimens for
fracture toughness measurement. The mode I and mixed-mode fracture toughnesses
are measured as a function of cementation, and are correlated with strength,
permeability and porosity. A micromechanical model is developed to predict the
dependence of mode I fracture toughness upon the degree of cementation. In
addition, the role of the crack tip -stress in dictating kink angle and
toughness is determined for mixed mode loading. At a sufficiently low degree of
cementation, the zone of microcracking in the vicinity of the crack tip is
sufficiently large for a crack tip -field to cease to exist and for crack
kinking theory to not apply. The interplay between cementation and fracture
properties of sedimentary rocks is explained; this understanding underpins a
wide range of rock fracture phenomena including hydraulic fracture
- …