Comparison of experimental and predicted performance of 150-millimeter-bore solid and drilled ball bearings to 3 million DN

Seven 150-millimeter-bore ball bearings were run under 8900-newton (2000-lbf) thrust load at speeds from 6670 to 20,000 rpm (1 million to 3 million DN). Four of the bearings had conventional solid balls, and three bearings had drilled (cylindrically hollow) balls with 50-percent mass reduction. The bearings were under-race cooled and slot lubricated with a type 2 ester oil at flow rates from 4.35 x 0.001 to 5.94 x 0.001 cubic meter/min (1.15 to 1.57 gal/min). Friction torque and temperature were measured on all bearings. While there was considerable spread in the temperature data, the drilled ball bearings tended to run slightly cooler than the solid ball bearings at higher speeds. No significant difference in torque was noted, however, between the solid and drilled ball bearings. One bearing of each type was rerun at 17,800-newton (4000-lbf) thrust load. The solid ball bearings performed satisfactorily at 3 million DN. However, at about 2 million DN the drilled ball bearing experienced a broken ball, and cracks appeared in other balls as a result of flexure fatigue. Metallurgical examination of the cracked balls indicated a brittle structure in the bore of the drilled balls

Dynamic load capacities of graphite fiber: Polyimide composites in oscillating plain bearings to 340 C (650 F)

Load capacities were determined for plain spherical bearings with self-lubricating spherical elements of graphite-fiber-reinforced-polyimide, and for plain cylindrical bearings with thin-wall liners of the composite in the bearing bores. Composites consisted of a 1-to-1 weight ratio of graphite fibers and polyimide. Oscillation was at an amplitude of + or - 15 deg at a frequency of 1 hertz. Bearings with composite ball material had a load capacity of approximately 69 MN/sq m (10 000 psi) at room temperature 25 MN/sq m (3600 psi) at 340 C (650 F). Bearings with thin-wall composite liners had much higher load capacities of 280 MN/sq m (40 000 psi) at room temperature amd 240 MN/sq m (35 000 psi) at 320 C (600 F). Friction coefficients were in the range of 0.12 to 0.19. The addition of 10 wt.% graphite fluoride solid lubricant to the composition of the thin-wall liners reduced friction coefficients into the range of 0.10 to 0.12

Effect of ball geometry on endurance limit in bending of drilled balls

Four designs of drilled (cylindrically hollow) balls were tested for resistance to bending fatigue. Bending fatigue has been demonstrated to be a limiting factor in previous evaluations of the drilled ball concept. A web reinforced drilled ball was most successful in resisting bending fatigue. Another design of through drilled design, involving a heavier wall than the standard reference ball, also showed significant improvement in resistance to bending fatigue

First Experiences Integrating PC Distributed I/O Into Argonne's ATLAS Control System

First Experiences Integrating PC Distributed I/O Into Argonne's ATLAS Control System The roots of ATLAS (Argonne Tandem-Linac Accelerator System) date back to the early 1960s. Located at the Argonne National Laboratory, the accelerator has been designated a National User Facility, which focuses primarily on heavy-ion nuclear physics. Like the accelerator it services, the control system has been in a constant state of evolution. The present real-time portion of the control system is based on the commercial product Vsystem [1]. While Vsystem has always been capable of distributed I/O processing, the latest offering of this product provides for the use of relatively inexpensive PC hardware and software. This paper reviews the status of the ATLAS control system, and describes first experiences with PC distributed I/O.Comment: ICALEPCS 2001 Conference, PSN WEAP027, 3 pages, 1 figur

Composite Reflective/Absorptive IR-Blocking Filters Embedded in Metamaterial Antireflection Coated Silicon

Infrared (IR) blocking filters are crucial for controlling the radiative loading on cryogenic systems and for optimizing the sensitivity of bolometric detectors in the far-IR. We present a new IR filter approach based on a combination of patterned frequency selective structures on silicon and a thin (50 $\mu \textrm{m}$ thick) absorptive composite based on powdered reststrahlen absorbing materials. For a 300 K blackbody, this combination reflects $\sim$50\% of the incoming light and blocks \textgreater 99.8\% of the total power with negligible thermal gradients and excellent low frequency transmission. This allows for a reduction in the IR thermal loading to negligible levels in a single cold filter. These composite filters are fabricated on silicon substrates which provide excellent thermal transport laterally through the filter and ensure that the entire area of the absorptive filter stays near the bath temperature. A metamaterial antireflection coating cut into these substrates reduces in-band reflections to below 1\%, and the in-band absorption of the powder mix is below 1\% for signal bands below 750 GHz. This type of filter can be directly incorporated into silicon refractive optical elements

Complementary influence functions for predicting subsidence caused by mining

Surface subsidence caused by underground mining is described through complementary influence functions. The complementary functions developed here differ from the simple functions previously used in that the surface displacement is the result of the combined contributions of the mined and unmined zones. This eliminates computational difficulties experienced with the simple functions in determining the deflections above the rib side and in the eventual application of influence functions to complex room-and-pillar configurations. Although the analysis framework presented is intended for predicting subsidence over complex mine configurations, use of the complementary functions is illustrated adequately by application to a longwall panel of the Old Ben No. 24 coal mine

The Relational Database Aspects of Argonne's ATLAS Control System

The Relational Database Aspects of Argonnes ATLAS Control System Argonnes ATLAS (Argonne Tandem Linac Accelerator System) control system comprises two separate database concepts. The first is the distributed real-time database structure provided by the commercial product Vsystem [1]. The second is a more static relational database archiving system designed by ATLAS personnel using Oracle Rdb [2] and Paradox [3] software. The configuration of the ATLAS facility has presented a unique opportunity to construct a control system relational database that is capable of storing and retrieving complete archived tune-up configurations for the entire accelerator. This capability has been a major factor in allowing the facility to adhere to a rigorous operating schedule. Most recently, a Web-based operator interface to the control systems Oracle Rdb database has been installed. This paper explains the history of the ATLAS database systems, how they interact with each other, the design of the new Web-based operator interface, and future plans.Comment: ICALEPCS 2001 Conference, PSN WEAP066, 3 pages, 3 figure

Global Diffusion in a Realistic Three-Dimensional Time-Dependent Nonturbulent Fluid Flow

We introduce and study the first model of an experimentally realizable three-dimensional time-dependent nonturbulent fluid flow to display the phenomenon of global diffusion of passive-scalar particles at arbitrarily small values of the nonintegrable perturbation. This type of chaotic advection, termed {\it resonance-induced diffusion\/}, is generic for a large class of flows.Comment: 4 pages, uuencoded compressed postscript file, to appear in Phys. Rev. Lett. Also available on the WWW from http://formentor.uib.es/~julyan/, or on paper by reques

Structural diversity in the type IV pili of multidrug-resistant Acinetobacter

Acinetobacter baumannii is a Gram-negative coccobacillus found primarily in hospital settings that has recently emerged as a source of hospital-acquired infections. A. baumannii expresses a variety of virulence factors, including type IV pili, bacterial extracellular appendages often essential for attachment to host cells. Here, we report the high resolution structures of the major pilin subunit, PilA, from three Acinetobacter strains, demonstrating thatA. baumannii subsets produce morphologically distinct type IV pilin glycoproteins. We examine the consequences of this heterogeneity for protein folding and assembly as well as host-cell adhesion by Acinetobacter. Comparisons of genomic and structural data with pilin proteins from other species of soil gammaproteobacteria suggest that these structural differences stem from evolutionary pressure that has resulted in three distinct classes of type IVa pilins, each found in multiple species

Reducing Controversy by Connecting Opposing Views

Peer reviewe