2,763 research outputs found
Elastic Properties in Tension and Shear of High Strength Nonferrous Metals and Stainless Steel - Effect of Previous Deformation and Heat Treatment
A resume is given of an investigation of the influence of plastic deformation and of annealing temperature on the tensile and shear elastic properties of high strength nonferrous metals and stainless steels in the form of rods and tubes. The data were obtained from earlier technical reports and notes, and from unpublished work in this investigation. There are also included data obtained from published and unpublished work performed on an independent investigation. The rod materials, namely, nickel, monel, inconel, copper, 13:2 Cr-Ni steel, and 18:8 Cr-Ni steel, were tested in tension; 18:8 Cr-Ni steel tubes were tested in shear, and nickel, monel, aluminum-monel, and Inconel tubes were tested in both tension and shear. There are first described experiments on the relationship between hysteresis and creep, as obtained with repeated cyclic stressing of annealed stainless steel specimens over a constant load range. These tests, which preceded the measurements of elastic properties, assisted in devising the loading time schedule used in such measurements. From corrected stress-set curves are derived the five proof stresses used as indices of elastic or yield strength. From corrected stress-strain curves are derived the secant modulus and its variation with stress. The relationship between the forms of the stress-set and stress-strain curves and the values of the properties derived is discussed. Curves of variation of proof stress and modulus with prior extension, as obtained with single rod specimens, consist in wavelike basic curves with superposed oscillations due to differences of rest interval and extension spacing; the effects of these differences are studied. Oscillations of proof stress and modulus are generally opposite in manner. The use of a series of tubular specimens corresponding to different amounts of prior extension of cold reduction gave curves almost devoid of oscillation since the effects of variation of rest interval and extension spacing were removed. Comparison is also obtained between the variation of the several properties, as measured in tension and in shear. The rise of proof stress with extension is studied, and the work-hardening rates of the various metals evaluated. The ratio between the tensile and shear proof stresses for the various annealed and cold-worked tubular metals is likewise calculated. The influence of annealing or tempering temperature on the proof stresses and moduli for the cold-worked metals and for air-hardened 13:2 Cr-Ni steel is investigated. An improvement of elastic strength generally is obtained, without important loss of yield strength, by annealing at suitable temperature. The variation of the proof stress and modulus of elasticity with plastic deformation or annealing temperature is explained in terms of the relative dominance of three important factors: namely, (a) internal stress, (b) lattice-expansion or work-hardening, and (c) crystal reorientation. Effective values of Poisson's ratio were computed from tensile and shear moduli obtained on tubular specimens. The variation of Poisson's ratio with plastic deformation and annealing temperature is explained in terms of the degree of anisotropy produced by changes of (a) internal stress and (b) crystal orientation
Diagnosis of an anaerobic pond treating temperate domestic wastewater: An alternative sludge strategy for small works
An anaerobic pond (AP) for treatment of temperate domestic wastewater has been studied as a small works sludge management strategy to challenge existing practice which comprises solids separation followed by open sludge storage, for up to 90 days. During the study, effluent temperature ranged between 0.1 °C and 21.1 °C. Soluble COD production was noted in the AP at effluent temperatures typically greater than 10 °C and was coincident with an increase in effluent volatile fatty acids (VFA) concentration, which is indicative of anaerobic degradation. Analysis from ports sited along the AP's length, demonstrated VFA to be primarily formed nearest the inlet where most solids deposition initially incurred, and confirmed the anaerobic reduction of sludge within this chamber. Importantly, the sludge accumulation rate was 0.06 m3 capita−1 y−1 which is in the range of APs operated at higher temperatures and suggests a de-sludge interval of 2.3–3.8 years, up to 10 times longer than current practice for small works. Coincident with the solids deposition profile, biogas production was predominantly noted in the initial AP section, though biogas production increased further along the AP's length following start-up. A statistically significant increase in mean biogas production of greater than an order of magnitude was measured between winters (t(n=19) = 5.52, P < 0.001) demonstrating continued acclimation. The maximum methane yield recorded was 2630 mgCH4 PE−1 d−1, approximately fifty times greater than estimated from sludge storage (57 mgCH4 PE−1 d−1). Anaerobic ponds at small works can therefore enable sludge reduction and longer sludge holding times than present thus offsetting tanker demand whilst reducing fugitive methane emissions currently associated with sludge storage, and based on the enhanced yield noted, could provide a viable opportunity for local energy generation
Shear elastic properties of some high strength nonferrous metals as affected by plastic deformation and by heat treatment
Torsional Elastic Properties of 18:8 Chromium-nickel Steel as Affected by Plastic Deformation and by Heat Treatment
The influence of plastic deformation and of heat treatment on Poisson's ratio for 18:8 chromium-nickel steel
IN3 COSTS ASSOCIATED WITH HCV AND RELATED COMPLICATIONS IN THE UNITED STATES FROM A MANAGED CARE PAYER'S PERSPECTIVE
Social effects of territorial neighbours on the timing of spring breeding in North American red squirrels
This is the author accepted manuscript. The final version is available from Wiley via the DOI in this recordOrganisms can affect one another’s phenotypes when they socially interact. Indirect genetic effects
occur when an individual’s phenotype is affected by genes expressed in another individual. These
heritable effects can enhance or reduce adaptive potential, thereby accelerating or reversing
evolutionary change. Quantifying these social effects is therefore crucial for our understanding of
evolution, yet estimates of indirect genetic effects in wild animals are limited to dyadic interactions.
We estimated indirect phenotypic and genetic effects, and their covariance with direct effects, for
the date of spring breeding in North American red squirrels (Tamiasciurus hudsonicus) living in an
array of territories of varying spatial proximity. Additionally, we estimated indirect effects and the
strength of selection at low and high population densities. Social effects of neighbours on the date of
spring breeding were different from zero at high population densities but not at low population
densities. Indirect phenotypic effects accounted for a larger amount of variation in the date of
breeding than differences attributable to the among-individual variance, suggesting social
interactions are important for determining breeding dates. The genetic component to these indirect
effects was however not statistically significant. We therefore showcase a powerful and flexible
method that will allow researchers working in organisms with a range of social systems to estimate
indirect phenotypic and genetic effects, and demonstrate the degree to which social interactions can
influence phenotypes, even in a solitary species
Identification of gas sparging regimes for granular anaerobic membrane bioreactor to enable energy neutral municipal wastewater treatment
In this study, conventional and novel gas sparging regimes have been evaluated for a municipal wastewater granular anaerobic MBR to identify how best to achieve high sustainable fluxes whilst simultaneously conserving energy demand. Using continuous gas sparging in combination with continuous filtration, flux was strongly dependent upon shear rate, which imposed a considerable energy demand. Intermittent gas sparging was subsequently evaluated to reduce energy demand whilst delivering an analogous shear rate. For a flux of 5 L m-2 h-1, a fouling rate below 1 mbar h-1 was sustained with low gas sparging frequency and gas sparging rates. However, to sustain low fouling rates for fluxes above 10 L m-2 h-1, a gas sparging frequency of 50 % (i.e. 10 s on/10 s off) and an increase in gas sparging rate is needed, indicating the importance of shear rate and gas sparging frequency. An alternative gas sparging regime was subsequently tested in which filtration was conducted without gas sparging, followed by membrane relaxation for a short period coupled with gas sparging, to create a pseudo dead-end filtration cycle. Fouling characterisation evidenced considerable cake fouling rates of 200-250 mbar h-1 within each filtration cycle. However, long term fouling transient analysis demonstrated low residual fouling resistance, suggesting the cake formed during filtration was almost completely reversible, despite operating at a flux of 15 L m-2 h-1, which was equivalent or higher than the critical flux of the suspension. It is therefore asserted that by operating filtration in the absence of shear, fouling is less dependent upon the preferential migration of the sub-micron particle fraction and is instead governed by the compressibility of the heterogeneous cake formed, which enables higher operational fluxes to be achieved. Comparison of energy demand for the three gas sparging regimes to the energy recovered from municipal wastewater AnMBR demonstrated that only by using dead-end filtration can energy neutral wastewater treatment be realised which is the ultimate ambition for the technology
- …