Slurry and dry particle erosion wear properties of WC-10Co4Cr and Cr3C2-25NiCr hardmetal coatings deposited by HVOF and HVAF spray processes

Thermally sprayed hardmetal coatings were produced to provide improved erosion wear compared to conventional cast GX4CrNi13-4 martensitic steel (CA6NM) used in hydro turbine components. Sprayed coatings and reference materials were tested with high-speed slurry pot tester using either fine or coarse quartz as the erosive media. Additional erosion tests were carried out with centrifugal dry erosion tester. Tungsten carbide based coatings provided the highest wear resistance due to the high hardness and even distribution of the fine carbide particles. The cast 13-4 steel samples experienced up to 180 times higher wear rates in fine quartz slurry and up to 36 times higher wear rates in coarse slurry compared to the sprayed coatings

Vildagliptin therapy reduces postprandial intestinal triglyceride-rich lipoprotein particles in patients with type 2 diabetes

Peer reviewe

A missense substitution A49T in the steroid 5-alpha-reductase gene (SRD5A2) is not associated with prostate cancer in Finland

Prostatic steroid 5-alpha-reductase gene (SRD5A2) encodes a critical enzyme involved in the conversion of testosterone to dihydrotestosterone. A germline mis-sense substitution (A49T) leads to a variant SRD5A2 protein, which has a 5-fold higher in vitro V max than the wild-type protein (Ross et al, 1998; Makridakis et al, 1999). The A49T variant was recently associated with 2.5 to 3.28-fold increased risk of prostate cancer (PC) in African-American and Hispanic men (Makridakis et al, 1999). Also, Jaffe et al (2000) reported an association between A49T and more aggressive disease among Caucasian patients. Here, we report that the prevalence of the A49T variant in 449 Finnish PC patients was 6.0%, not significantly different from 6.3% observed in 223 patients with benign prostatic hyperplasia or 5.8% in 588 population-based controls (odds ratio for PC 1.04, 95% C.I. 0.62–1.76 P = 0.89). There was no association between A49T and the family history of the patients nor with tumour stage or grade. Our results argue against a prominent role of the A49T variant as a genetic risk factor for prostate cancer development and progression in the Finnish population. © 2001 Cancer Research Campaign www.bjcancer.co

Sliding and abrasive wear behaviour of HVOF- and HVAF-sprayed Cr3C2-NiCr hardmetal coatings

This paper provides a comprehensive characterisation of HVOF- and HVAF-sprayed Cr3C2-25 wt.% NiCr hardmetal coatings. One commercial powder composition with two different particle size distributions was processed using five HVOF and HVAF thermal spray systems. All coatings contain less Cr3C2 than the feedstock powder, possibly due to the rebound of some Cr3C2-rich particles during high-velocity impact onto the substrate. Dry sand-rubber wheel abrasive wear testing causes both grooving and pull-out of splat fragments. Mass losses depend on inter- and intra-lamellar cohesion, being higher (≥70 mg after a wear distance of 5904 m) for the coatings deposited with the coarser feedstock powder or with one type of HVAF torch. Sliding wear at room temperature against alumina involves shallower abrasive grooving, small-scale delamination and carbide pull-outs, and it is controlled by intra-lamellar cohesion. The coatings obtained from the fine feedstock powder exhibit the lowest wear rates (≈5×10-6 mm3/(Nm)). At 400 °C, abrasive grooving dominates the sliding wear behaviour; wear rates increase by one order of magnitude but friction coefficients decrease from ≈0.7 to ≈0.5. The thermal expansion coefficient of the coatings (11.08×10-6 °C-1 in the 30-400 °C range) is sufficiently close to that of the steel substrate (14.23×10-6 °C-1) to avoid macro-cracking

Interrelationships Between the Kinetics of VLDL Subspecies and HDL Catabolism in Abdominal Obesity: A Multicenter Tracer Kinetic Study

Context: Low plasma high-density lipoprotein (HDL) cholesterol is a major abnormality in abdominal obesity. This relates due to accelerated HDL catabolism, but the underlying mechanism requires further elucidation. The relationships between HDL catabolism and other variables that may be modified in abdominal obesity, such as very low-density lipoprotein (VLDL) subspecies (VLDL1, VLDL2) kinetics, liver fat, or visceral adiposity, remain to be investigated. Objectives: Our aim was to study the associations between HDL apolipoprotein (apo)-A-I fractional catabolic rate (FCR) and the kinetics of VLDL subspecies and estimates of liver and visceral and sc fat. Design: We carried out a multicenter in vivo kinetic study using stable isotopes (deuterated leucine and glycerol) in 62 individuals with abdominal obesity. Results: In a multivariate analysis, among the morphological and biological parameters that may predict apoA-I FCR, liver fat (beta = .400, P = .003), and VLDL1-apoB (beta = .307, P = .020) were independently associated with apoA-I FCR. In a multivariate analysis, among the kinetic parameters, VLDL1-triglycerides (TGs) indirect FCR (beta = .357, P = .001), VLDL1-TG production rate (beta = 0.213, P = .048), and apoA-II FCR (beta = .667, P < .0001) were independently associated with apoA-I FCR. After adjustment for VLDL1-TG production rate, liver fat was no more correlated with apoA-I FCR. No association between apoA-I FCR and visceral fat was observed. Conclusions: We show that VLDL1 is an important independent determinant of apoA-I FCR and more precisely that apoA-I FCR is independently associated with both catabolism and the production of VLDL1-TG. In addition, we show an association between liver fat and apoA-I FCR that is mostly mediated by VLDL1-TG production. These data indicate that, in abdominal obesity, dysfunctional VLDL1 metabolism is an important modulator of HDL apoA-I catabolism

Tribology of HVOF- and HVAF-sprayed WC-10Co4Cr hardmetal coatings: A comparative assessment

This paper provides a comprehensive assessment of the sliding and abrasive wear behaviour of WC-10Co4Cr hardmetal coatings, representative of the existing state-of-the-art. A commercial feedstock powder with two different particle size distributions was sprayed onto carbon steel substrates using two HVOF and two HVAF spray processes. Mild wear rates of <10-7mm3/(Nm) and friction coefficients of 480.5 were obtained for all samples in ball-on-disk sliding wear tests at room temperature against Al2O3 counterparts. WC-10Co4Cr coatings definitely outperform a reference electrolytic hard chromium coating under these test conditions. Their wear mechanisms include extrusion and removal of the binder matrix, with the formation of a wavy surface morphology, and brittle cracking. The balance of such phenomena is closely related to intra-lamellar features, and rather independent of those properties (e.g. indentation fracture toughness, elastic modulus) which mainly reflect large-scale inter-lamellar cohesion, as quantitatively confirmed by a principal component analysis. Intra-lamellar dissolution of WC into the matrix indeed increases the incidence of brittle cracking, resulting in slightly higher wear rates. At 400\ub0C, some of the hardmetal coatings fail because of the superposition between tensile residual stresses and thermal expansion mismatch stresses (due to the difference between the thermal expansion coefficients of the steel substrate and of the hardmetal coating). Those which do not fail, on account of lower residual stresses, exhibit higher wear rates than at room temperature, due to oxidation of the WC grains.The resistance of the coatings against abrasive wear, assessed by dry sand-rubber wheel testing, is related to inter-lamellar cohesion, as proven by a principal component analysis of the collected dataset. Therefore, coatings deposited from coarse feedstock powders suffer higher wear loss than those obtained from fine powders, as brittle inter-lamellar detachment is caused by their weaker interparticle cohesion, witnessed by their systematically lower fracture toughness as well

Fructose intervention for 12 weeks does not impair glycemic control or incretin hormone responses during oral glucose or mixed meal tests in obese men

Background and aims: Incretin hormones glucagon-like peptide (GLP)-1 and glucose-dependent insulinotropic polypeptide (GIP) are affected early on in the pathogenesis of metabolic syndrome and type 2 diabetes. Epidemiologic studies consistently link high fructose consumption to insulin resistance but whether fructose consumption impairs the incretin response remains unknown. Methods and results: As many as 66 obese (BMI 26-40 kg/m(2)) male subjects consumed fructose-sweetened beverages containing 75 g fructose/day for 12 weeks while continuing their usual lifestyle. Glucose, insulin, GLP-1 and GIP were measured during oral glucose tolerance test (OGTT) and triglycerides (TG), GLP-1, GIP and PYY during a mixed meal test before and after fructose intervention. Fructose intervention did not worsen glucose and insulin responses during OGTT, and GLP-1 and GIP responses during OGTT and fat-rich meal were unchanged. Postprandial TG response increased significantly, p = 0.004, and we observed small but significant increases in weight and liver fat content, but not in visceral or subcutaneous fat depots. However, even the subgroups who gained weight or liver fat during fructose intervention did not worsen their glucose, insulin, GLP-1 or PYY responses. A minor increase in GIP response during OGTT occurred in subjects who gained liver fat (p = 0.049). Conclusion: In obese males with features of metabolic syndrome, 12 weeks fructose intervention 75 g/day did not change glucose, insulin, GLP-1 or GIP responses during OGTT or GLP-1, GIP or PYY responses during a mixed meal. Therefore, fructose intake, even accompanied with mild weight gain, increases in liver fat and worsening of postprandial TG profile, does not impair glucose tolerance or gut incretin response to oral glucose or mixed meal challenge. (C) 2017 The Italian Society of Diabetology, the Italian Society for the Study of Atherosclerosis, the Italian Society of Human Nutrition, and the Department of Clinical Medicine and Surgery, Federico II University. Published by Elsevier B.V. All rights reserved.Peer reviewe

Adrenal androgens versus cortisol for primary aldosteronism subtype determination in adrenal venous sampling

Objective: We examined if measurement of adrenal androgens adds to subtype diagnostics of primary aldosteronism (PA) under cosyntropin-stimulated adrenal venous sampling (AVS).Design: A prospective pre-specified secondary endpoint analysis of 49 patients with confirmed PA, of whom 29 underwent unilateral adrenalectomy with long-term follow-up.Methods: Concentrations of androstenedione, dehydroepiandrosterone (DHEA) and dehydroepiandrosterone sulphate (DHEAS) were measured during AVS in addition to aldosterone and cortisol. Subjects with lateralisation index (LI) of ≥4 were treated with unilateral adrenalectomy, and the immunohistochemical subtype was determined with CYP11B2 and CYP11B1 stains. The performance of adrenal androgens was evaluated by receiver operating characteristics (ROC) curve analyses in adrenalectomy and medical therapy groups.Results: During AVS, the correlations between cortisol and androstenedione, DHEA and DHEAS for LI and selectivity index (SI) were highly significant. The right and left side SIs for androstenedione and DHEA were higher (p Conclusions: Under cosyntropin-stimulated AVS, the measurement of androstenedione and DHEA did not improve the cannulation selectivity. The performance of cortisol and adrenal androgens are confirmatory but not superior to cortisol-based results in lateralisation diagnostics of PA.</p

The LAGUNA design study- towards giant liquid based underground detectors for neutrino physics and astrophysics and proton decay searches

The feasibility of a next generation neutrino observatory in Europe is being considered within the LAGUNA design study. To accommodate giant neutrino detectors and shield them from cosmic rays, a new very large underground infrastructure is required. Seven potential candidate sites in different parts of Europe and at several distances from CERN are being studied: Boulby (UK), Canfranc (Spain), Fr\'ejus (France/Italy), Pyh\"asalmi (Finland), Polkowice-Sieroszowice (Poland), Slanic (Romania) and Umbria (Italy). The design study aims at the comprehensive and coordinated technical assessment of each site, at a coherent cost estimation, and at a prioritization of the sites within the summer 2010.Comment: 5 pages, contribution to the Workshop "European Strategy for Future Neutrino Physics", CERN, Oct. 200