A Rapid Magnetofluidic Micromixer Using Diluted Ferrofluid

Effective and rapid mixing is essential for various chemical and biological assays. The present work describes a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A superparamagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 88% in a relatively short microchannel

A Rapid Magnetofluidic Micromixer Using Diluted Ferrofluid

Effective and rapid mixing is essential for various chemical and biological assays. The present work describes a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A superparamagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 88% in a relatively short microchannel

Lab on a chip for continuous-flow magnetic cell separation

Separation of cells is a key application area of lab-on-a-chip (LOC) devices. Among the various methods, magnetic separation of cells utilizing microfluidic devices offers the merits of biocompatibility, efficiency, and simplicity. This review discusses the fundamental physics involved in using magnetic force to separate particles, and identifies the optimisation parameters and corresponding methods for increasing the magnetic force. The paper then elaborates the design considerations of LOC devices for continuous-flow magnetic cell separation. Examples from the recently published literature illustrate these state-of-the-art techniques

Antileishmanial activity of Ferula assa-foetida oleo gum resin against Leishmania major: An in vitro study

Background: In Ayurveda, asafetida is introduced as a valuable remedy for flatulence, hysteria, nervous disorders, whooping cough, pneumonia and bronchitis in children and also considered as an aphrodisiac agent. Presently, Leishmaniasis is common in most countries of the world and is a serious health problem in the world. Some plant medicines and natural products have a new candidate for treatment of leishmaniasis. Objective: This study was designed to evaluate Ferula assa-foetida oleo gum resin (asafetida) on mortality and morbidity Leishmania major in vitro. Materials and Methods: Mostigotes were isolated from mice spleens and then transformed to promastigotes in Novy-Nicolle-Mac Neal (NNN medium supplemented with penicillin (100 U/ml), streptomycin (100 μg/ml) and 20% heat-inactivated fetal calf serum (FCS) at 25°C. A fixed initial density of the parasites was transferred to screw-capped vials containing 5 ml of RPMI 1640 media to which different concentrations of 2.5, 5, 10 and 20 μg asafetida were added and each concentration was done in triplicates. Each run also included control. The mortality of parasitoids was measured by the slide and the enzyme-linked immunosorbent assay (ELISA) methods. Results: After 72 h, asafetida inhibited growth of parasites in all doses in stationary and logarithmic phases. The ELISA measurement suggested that the viability of parasites significantly decreased after 48h (P < 0.05). Conclusion: The results show that asafetida could prevent from growth and viability of parasites and this oleo gum resin can be useful for treatment of leishmaniasis

Relaxant effect of Humulus lupulus extracts on isotonic rat's ileum contractions

O Objective: Many biological studies have been done to determine the activity of medicinal plants on gastrointestinal function. Since acetylcholine is the major transmitter involved in the gastrointestinal motility and there are some evidences regarding the cholinergic modulatory effect of hops extract, in the present study spasmolytic and antispasmodic action of hops(Humulus lupulus) on acetylcholine-induced contraction in isolated rat's ileum was evaluated. Material and Methods: In this study, pieces of isolated rat's ileum were mounted in the internal chamber of an organ bath which was filled with Tyrode’s solution and tightly tied to the lever of an isotonic transducer. The contractile responses were recorded by using an oscillograph device. In the presence of normal saline and different concentrations of hops (0.1, 0.3, and 0.5 mg/ml), the amplitude of contractions induced by10-12 up to 10-2 M acetylcholine was determined. The spasmolytic action of the same extract concentrations was also examined on contraction induced by 10-4 acetylcholine. Results: Our findings indicate that hops extract reduces acetylcholine-induced contraction in all concentrations. The significant inhibitory effects of 0.1, 0.3, and 0.5 mg/ml hops extract on contraction induced by 10-3 M acetylcholine were 81.9, 77, and 29.3, respectively (

Application of high-order lattice Boltzmann for binary diffusive mixing in microfluidics: Comparison against fluorescent microscopy

Diffusive mixing between miscible fluids is an important process in many microfluidic applications, especially for biological studies. In microfluidic experiments it is common to observe microscopic fluid dynamics through fluorescence microscopy. Applying this technique to a hydrodynamic focusing device with a core-flow containing ferrofluid and fluorescence, an unexpected physical phenomenon referred to as the ‘saddle-like’ distribution was observed. Lattice Boltzmann (LB) methods have recently gained tremendous popularity as a numerical approach to model microfluidic dynamics. Despite the recent advancements in LB, reports on the application of high-order LB methods to single- phase miscible mixtures in microfluidics have been limited. The work presented here focuses on the application of high-order LB models to the simulation of single-phase binary miscible mixtures in microfluidic systems. We demonstrate the ability of our numerical simulation to capture the characteristics of the ‘saddle-like’ phenomenon and highlight the difficulties and limitations faced when comparing numerical results against experimental fluorescence microscopy with ferrofluids. This work sets the preliminary steps towards a LB model for simulating fluid mixtures in micro- and nanofluidics and allows for future advancements through higher order expansions

Observations of phase changes in monoolein during high viscous injection

Serial crystallography of membrane proteins often employs high-viscosity injectors (HVIs) to deliver micrometre-sized crystals to the X-ray beam. Typically, the carrier medium is a lipidic cubic phase (LCP) media, which can also be used to nucleate and grow the crystals. However, despite the fact that the LCP is widely used with HVIs, the potential impact of the injection process on the LCP structure has not been reported and hence is not yet well understood. The self-assembled structure of the LCP can be affected by pressure, dehydration and temperature changes, all of which occur during continuous flow injection. These changes to the LCP structure may in turn impact the results of X-ray diffraction measurements from membrane protein crystals. To investigate the influence of HVIs on the structure of the LCP we conducted a study of the phase changes in monoolein/water and monoolein/buffer mixtures during continuous flow injection, at both atmospheric pressure and under vacuum. The reservoir pressure in the HVI was tracked to determine if there is any correlation with the phase behaviour of the LCP. The results indicated that, even though the reservoir pressure underwent (at times) significant variation, this did not appear to correlate with observed phase changes in the sample stream or correspond to shifts in the LCP lattice parameter. During vacuum injection, there was a three-way coexistence of the gyroid cubic phase, diamond cubic phase and lamellar phase. During injection at atmospheric pressure, the coexistence of a cubic phase and lamellar phase in the monoolein/water mixtures was also observed. The degree to which the lamellar phase is formed was found to be strongly dependent on the co-flowing gas conditions used to stabilize the LCP stream. A combination of laboratory-based optical polarization microscopy and simulation studies was used to investigate these observations

Observations of phase changes in monoolein during high viscous injection

Serial crystallography of membrane proteins often employs high-viscosity injectors (HVIs) to deliver micrometre-sized crystals to the X-ray beam. Typically, the carrier medium is a lipidic cubic phase (LCP) media, which can also be used to nucleate and grow the crystals. However, despite the fact that the LCP is widely used with HVIs, the potential impact of the injection process on the LCP structure has not been reported and hence is not yet well understood. The self-assembled structure of the LCP can be affected by pressure, dehydration and temperature changes, all of which occur during continuous flow injection. These changes to the LCP structure may in turn impact the results of X-ray diffraction measurements from membrane protein crystals. To investigate the influence of HVIs on the structure of the LCP we conducted a study of the phase changes in monoolein/water and monoolein/buffer mixtures during continuous flow injection, at both atmospheric pressure and under vacuum. The reservoir pressure in the HVI was tracked to determine if there is any correlation with the phase behaviour of the LCP. The results indicated that, even though the reservoir pressure underwent (at times) significant variation, this did not appear to correlate with observed phase changes in the sample stream or correspond to shifts in the LCP lattice parameter. During vacuum injection, there was a three-way coexistence of the gyroid cubic phase, diamond cubic phase and lamellar phase. During injection at atmospheric pressure, the coexistence of a cubic phase and lamellar phase in the monoolein/water mixtures was also observed. The degree to which the lamellar phase is formed was found to be strongly dependent on the co-flowing gas conditions used to stabilize the LCP stream. A combination of laboratory-based optical polarization microscopy and simulation studies was used to investigate these observations