Conceptual study of an advanced supersonic technology transport (AST-107) for transpacific range using low-bypass-ratio turbofan engines

An advanced supersonic technology configuration concept designated the AST-107, using a low bypass ratio turbofan engine, is described and analyzed. The aircraft had provisions for 273 passengers arranged five abreast. The cruise Mach number was 2.62. The mission range for the AST-107 was 8.48 Mm (4576 n.mi.) and an average lift drag ratio of 9.15 during cruise was achieved. The available lateral control was not sufficient for the required 15.4 m/s (30 kt) crosswind landing condition, and a crosswind landing gear or a significant reduction in dihedral effect would be necessary to meet this requirement. The lowest computed noise levels, including a mechanical suppressor noise reduction of 3 EPNdB at the flyover and sideline monitoring stations, were 110.3 EPNdB (sideline noise), 113.1 EPNdB (centerline noise) and 110.5 EPNdB (approach noise)

Aero-Thermal Calibration of the NASA Glenn Icing Research Tunnel (2012 Test)

A major modification of the refrigeration plant and heat exchanger at the NASA Glenn Icing Research Tunnel (IRT) occurred in autumn of 2011. It is standard practice at NASA Glenn to perform a full aero-thermal calibration of the test section of a wind tunnel facility upon completion of major modifications. This paper will discuss the tools and techniques used to complete an aero-thermal calibration of the IRT and the results that were acquired. The goal of this test entry was to complete a flow quality survey and aero-thermal calibration measurements in the test section of the IRT. Test hardware that was used includes the 2D Resistive Temperature Detector (RTD) array, 9-ft pressure survey rake, hot wire survey rake, and the quick check survey rake. This test hardware provides a map of the velocity, Mach number, total and static pressure, total temperature, flow angle and turbulence intensity. The data acquired were then reduced to examine pressure, temperature, velocity, flow angle, and turbulence intensity. Reduced data has been evaluated to assess how the facility meets flow quality goals. No icing conditions were tested as part of the aero-thermal calibration. However, the effects of the spray bar air injections on the flow quality and aero-thermal calibration measurements were examined as part of this calibration

Geometric-Phase-Effect Tunnel-Splitting Oscillations in Single-Molecule Magnets with Fourth-Order Anisotropy Induced by Orthorhombic Distortion

We analyze the interference between tunneling paths that occurs for a spin system with both fourth-order and second-order transverse anisotropy. Using an instanton approach, we find that as the strength of the second-order transverse anisotropy is increased, the tunnel splitting is modulated, with zeros occurring periodically. This effect results from the interference of four tunneling paths connecting easy-axis spin orientations and occurs in the absence of any magnetic field.Comment: 6 pages, 5 eps figures. Version published in EPL. Expanded from v1: Appendix added, references added, 1 figure added, others modified cosmeticall

AN INVESTIGATION OF MODIFIED CLUSTERED JET-EXIT ARRANGEMENTS AT SUPERSONIC SPEEDS

Modified clustered jet-exit arrangements at supersonic speed

Use of RIP to inactivate genes in Neurospora crassa.

About two years ago we suggested that a novel genetic mechanism, operating in the period between fertilization and nuclear fusion in Neurospora, scans the genome for sequence dupliations and alters them (Selker E. et al. 1987 Cell 51:741-752)

miR-1254 and miR-574-5p: Serum-Based microRNA Biomarkers for Early-Stage Non-small Cell Lung Cancer

n/

Comparison of dynamic cobble berm revetments with differing gravel characteristics

Pressure on the coastline is escalating due to the impacts of climate change, this is leading to a rise in sea-levels and intensifying storminess. Consequently, many regions of the coast are at increased risk of erosion and flooding. Therefore coastal protection schemes will increase in cost and scale. In response there is a growing use of nature-based coastal protection which aim to be sustainable, effective and adaptable. An example of a nature-based solution is a dynamic cobble berm revetment: a berm constructed from cobble and other gravel sediments at the high tide wave runup limit. These structures limit wave excursion protecting the hinterland from inundation, stabilise the upper beach and adapt to changes in water level. Recent experiments and field applications have shown the suitability of these structures for coastal protection, however many of the processes and design considerations are poorly understood. This study directly compares two prototype scale laboratory experiments which tested dynamic cobble berm revetments constructed with approximately the same geometry but differing gravel characteristics; well-sorted rounded gravel (DynaRev1) and poorly-sorted angular gravel (DynaRev2). In both cases the structures were tested using identical wave forcing including incrementally increasing water level and erosive wave conditions. The results presented in this paper demonstrate that both designs responded to changing water level and wave conditions by approaching a dynamically stable state, where individual gravel is mobilised under wave action but the geometry remains approximately constant. Further, both structures acted to reduce swash excursions compared to a pure sand beach. However, their morphological behaviour is response to wave action varied considerably. Once overtopping of the designed crest occurred, the poorly-sorted revetment developed a peaked crest which grew in elevation as the water level or wave height increased, further limited overtopping. By comparison, the well-sorted revetment was characterised by a larger volume of submerged gravel and a lower elevation flat crest which responded less well to changes in conditions. This occurred due to two processes: (1) for the poorly-sorted case, gravel sorting processes moved small to medium gravel material (D50<70mm) to the crest and (2) the angular nature of the poorly-sorted gravel material promoted increased interlocking. Both of these processes led to a gravel matrix that is more resistant to wave action and gravitational effects. Both revetments experienced some sinking due to sand erosion beneath the front slope. The rate of sinking for the well-sorted case was larger and continued throughout due to the large pore spaces within the gravel matrix. For the poorly sorted revetment in DynaRev2, sand erosion ceased after approximately 28 h due to the development of a filter layer of small gravel at the sand-gravel interface reducing porosity at this location, hence a larger volume of sand was preserved beneath the structure. Both designs present a low-cost and effective solution for protecting sandy coastlines but from an engineering viewpoint it appears better to avoid well-sorted gravel material and greater gravel angularity has been seen to increase crest stability