An overview of the fundamental aerodynamics branch's research activities in wing leading-edge vortex flows at supersonic speeds

For the past 3 years, a research program pertaining to the study of wing leading edge vortices at supersonic speeds has been conducted in the Fundamental Aerodynamics Branch of the High-Speed Aerodynamics Division at the Langley Research Center. The purpose of the research is to provide an understanding of the factors governing the formation and the control of wing leading-edge vortices and to evaluate the use of these vortices for improving supersonic aerodynamic performance. The studies include both experimental and theoretical investigations and focus primarily on planform, thickness and camber effects for delta wings. An overview of this research activity is presented

Experimental and theoretical study of the longitudinal aerodynamic characteristics of delta and double-delta wings at Mach numbers of 1.60, 1.90, and 2.16

An experimental and theoretical study was conducted to investigate the supersonic aerodynamic characteristics of delta and double-delta wings. Testing was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.90, and 2.16. The double-delta wings exhibited lower zero-lift drag values than the delta wings having the same aspect ratio, whereas delta wings provided the lower drag due to lift. Deflections of the trailing-edge flaps for pitch control revealed that the induced aerodynamic forces were only a function of the flap planform and were independent of wing planform. The supporting theoretical analysis showed that the supersonic design and analysis system (SDAS) did not consistently predict all the longitudinal aerodynamic characteristics of the low-sweep, low-fineness-ratio wing-body configurations under investigation

Laser transit anemometer measurements on a slender cone in the Langley unitary plan wind tunnel

A laser transit anemometer (LTA) system was used to probe the boundary layer on a slender (5 degree half angle) cone model in the Langley unitary plan wind tunnel. The anemometer system utilized a pair of laser beams with a diameter of 40 micrometers spaced 1230 micrometers apart to measure the transit times of ensembles of seeding particles using a cross-correlation technique. From these measurements, boundary layer profiles around the model were constructed and compared with CFD calculations. The measured boundary layer profiles representing the boundary layer velocity normalized to the edge velocity as a function of height above the model surface were collected with the model at zero angle of attack for four different flow conditions, and were collected in a vertical plane that bisected the model's longitudinal center line at a location 635 mm from the tip of the forebody cone. The results indicate an excellent ability of the LTA system to make velocity measurements deep into the boundary layer. However, because of disturbances in the flow field caused by onboard seeding, premature transition occurred implying that upstream seeding is mandatory if model flow field integrity is to be maintained. A description and results of the flow field surveys are presented

Effect of leading- and trailing-edge flaps on clipped delta wings with and without wing camber at supersonic speeds

An experimental investigation of the aerodynamic characteristics of thin, moderately swept fighter wings has been conducted to evaluate the effect of camber and twist on the effectiveness of leading- and trailing-edge flaps at supersonic speeds in the Langley Unitary Plan Wind Tunnel. The study geometry consisted of a generic fuselage with camber typical of advanced fighter designs without inlets, canopy, or vertical tail. The model was tested with two wing configurations an uncambered (flat) wing and a cambered and twisted wing. Each wing had an identical clipped delta planform with an inboard leading edge swept back 65 deg and an outboard leading edge swept back 50 deg. The trailing edge was swept forward 25 deg. The leading-edge flaps were deflected 4 deg to 15 deg, and the trailing-edge flaps were deflected from -30 deg to 10 deg. Longitudinal force and moment data were obtained at Mach numbers of 1.60, 1.80, 2.00, and 2.16 for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.16 x 10(exp 6) per foot and for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.0 x 10(exp 6) per foot. Vapor screen, tuft, and oil flow visualization data are also included

Investigation of leading-edge flap performance on delta and double-delta wings at supersonic speeds

An investigation of the aerodynamic performance of leading-edge flaps on three clipped delta and three clipped double-delta wing planforms with aspect ratios of 1.75, 2.11, and 2.50 was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.90, and 2.16. A primary set of fullspan leading-edge flaps with similar root and tip chords were investigated on each wing, and several alternate flap planforms were investigated on the aspect-ratio-1.75 wings. All leading-edge flap geometries were effective in reducing the drag at lifting conditions over the range of wing aspect ratios and Mach numbers tested. Application of a primary flap resulted in better flap performance with the double-delta planform than with the delta planform. The primary flap geometry generally yielded better performance than the alternate flap geometries tested. Trim drag due to flap-induced pitching moments was found to reduce the leading-edge flap performance more for the delta planform than for the double-delta planform. Flow-visualization techniques showed that leading-edge flap deflection reduces crossflow shock-induced separation effects. Finally, it was found that modified linear theory consistently predicts only the effects of leading-edge flap deflection as related to pitching moment and lift trends

An annotated list of the Lepidoptera of Honduras

A biodiversity inventory of the Lepidoptera of Pico Bonito National Park and vicinity, in the Department of Atlantida of northern Honduras, was initiated in 2009 to obtain baseline data. We present a revised checklist of Honduran butterfly species (updated from the initial 1967 lists), as well as the first comprehensive list of Honduran moths. Our updated list includes 550 species of Papilionoidea, 311 Hesperioidea, and 1,441 moth species

An annotated list of the Lepidoptera of Honduras

A biodiversity inventory of the Lepidoptera of Pico Bonito National Park and vicinity, in the Department of Atlantida of northern Honduras, was initiated in 2009 to obtain baseline data. We present a revised checklist of Honduran butterfly species (updated from the initial 1967 lists), as well as the first comprehensive list of Honduran moths. Our updated list includes 550 species of Papilionoidea, 311 Hesperioidea, and 1,441 moth species