Dimensional changes of CAD/CAM polymer crowns after water aging - An in vitro experiment

Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) polymers can potentially replace traditional materials used for manufacturing indirect restorations. In 2012, Lava Ultimate (LU) was introduced as a highly suitable material for implant-supported single crowns. Three years after its introduction, the manufacturer issued a change in indication for the material, implying that they no longer considered the material to be suitable for crown indications due to debonding issues. A clinical trial with implant-borne Lava Ultimate crowns bonded to zirconia abutments revealed that 80 percent of the LU crowns showed debonding from the abutment within one year, whereas no debonding occurred when an alternative full-ceramic restoration material was used. These results suggest that the material itself had been the cause of the debonding. However, the exact reason for the debonding remained unclear. Water uptake in resin methacrylates like LU is known to cause dimensional changes resulting in mechanical stress on the RelyX Ultimate (RU) cement. The purpose of this study is to quantify the dimensional changes in LU caused by water uptake and relate these dimensional changes to the failure of the RU cement. Twenty-five identical LU-crowns were divided into three groups. 10 LU-crowns with abutment and 10 crowns without abutments were stored in water for 23 days and were only removed for measurement. Five crowns served as a control to calibrate the measurements. The internal diameter was measured eight times with a TS 460 Heidenhain touch probe. For visualization purposes, one crown was also 3D scanned before and after water treatment. The results showed that after 23 days in water the mean increase in diameter for the groups with and without abutment was 36.6 μm (SD = 35,1) and 36.7 μm (SD = 26,5) respectively. Mixed effects modelling indicated no significant between-group differences at any time point. Exposure of LU to water results in dimensional changes causing mechanical stress on the crown-abutment complex. It can be estimated that RU cement fails after an expansion of more than 4 μm. Within the limitations of this in vitro study, it can be concluded that the dimensional changes induced by water uptake can cause debonding issues. As more CAD/CAM polymers for restorative purposes are expected to be developed, the results of this study should stimulate manufacturers to quantify their products' dimensional changes in a wet environment before market release

Fluorescent Labeling and 2-Photon Imaging of Mouse Tooth Pulp Nociceptors

Retrograde fluorescent labeling of dental primary afferent neurons (DPANs) has been described in rats through crystalline fluorescent DiI, while in the mouse, this technique was achieved with only Fluoro-Gold, a neurotoxic fluorescent dye with membrane penetration characteristics superior to the carbocyanine dyes. We reevaluated this technique in the rat with the aim to transfer it to the mouse because comprehensive physiologic studies require access to the mouse as a model organism. Using conventional immunohistochemistry, we assessed in rats and mice the speed of axonal dye transport from the application site to the trigeminal ganglion, the numbers of stained DPANs, and the fluorescence intensity via 1) conventional crystalline DiI and 2) a novel DiI formulation with improved penetration properties and staining efficiency. A 3-dimensional reconstruction of an entire trigeminal ganglion with 2-photon laser scanning fluorescence microscopy permitted visualization of DPANs in all 3 divisions of the trigeminal nerve. We quantified DPANs in mice expressing the farnesylated enhanced green fluorescent protein (EGFPf) from the transient receptor potential cation channel subfamily M member 8 (TRPM8EGFPf/+) locus in the 3 branches. We also evaluated the viability of the labeled DPANs in dissociated trigeminal ganglion cultures using calcium microfluorometry, and we assessed the sensitivity to capsaicin, an agonist of the TRPV1 receptor. Reproducible DiI labeling of DPANs in the mouse is an important tool 1) to investigate the molecular and functional specialization of DPANs within the trigeminal nociceptive system and 2) to recognize exclusive molecular characteristics that differentiate nociception in the trigeminal system from that in the somatic system. A versatile tool to enhance our understanding of the molecular composition and characteristics of DPANs will be essential for the development of mechanism-based therapeutic approaches for dentine hypersensitivity and inflammatory tooth pain

Postoperative pain intensity after using different instrumentation techniques: a randomized clinical study

Postoperative pain is a frequent complication associated with root canal treatment, especially during apical instrumentation of tooth with preexisting periradicular inflammation OBJECTIVES: The aim of this clinical study was to evaluate the influence of the instrumentation techniques on the incidence and intensity of postoperative pain in single-visit root canal treatment. MATERIAL AND METHODS: Ninety patients with single root/canal and non-vital pulps were included. The patients were assigned into 3 groups according to root canal instrumentation technique used; modified step-back, reciprocal, and rotational techniques. Root canal treatment was carried out in a single visit and the severity of postoperative pain was assessed via 4-point pain intensity scale. All the participants were called through the phone at 12, 24 and 48 h to obtain the pain scores. Data were analyzed through the Kruskal–Wallis test. RESULTS: There was significant difference between all groups (p<0.05). The modified step-back technique produced postoperative pain significantly lower than the rotational (p=0.018) and reciprocal (p=0.020) techniques. No difference was found between the reciprocal and rotational techniques (p=0.868). Postoperative pain in the first 12 h period (p=0.763) and in the 24 h period (p=0.147) was not significantly different between the groups. However, the difference in the 48 h period was statistically different between the groups (p=0.040). CONCLUSION: All instrumentation techniques caused postoperative pain. The modified step-back technique produced less pain compared to the rotational and reciprocal techniques

Review of nanomaterials in dentistry: interactions with the oral microenvironment, clinical applications, hazards, and benefits.

Interest in the use of engineered nanomaterials (ENMs) as either nanomedicines or dental materials/devices in clinical dentistry is growing. This review aims to detail the ultrafine structure, chemical composition, and reactivity of dental tissues in the context of interactions with ENMs, including the saliva, pellicle layer, and oral biofilm; then describes the applications of ENMs in dentistry in context with beneficial clinical outcomes versus potential risks. The flow rate and quality of saliva are likely to influence the behavior of ENMs in the oral cavity, but how the protein corona formed on the ENMs will alter bioavailability, or interact with the structure and proteins of the pellicle layer, as well as microbes in the biofilm, remains unclear. The tooth enamel is a dense crystalline structure that is likely to act as a barrier to ENM penetration, but underlying dentinal tubules are not. Consequently, ENMs may be used to strengthen dentine or regenerate pulp tissue. ENMs have dental applications as antibacterials for infection control, as nanofillers to improve the mechanical and bioactive properties of restoration materials, and as novel coatings on dental implants. Dentifrices and some related personal care products are already available for oral health applications. Overall, the clinical benefits generally outweigh the hazards of using ENMs in the oral cavity, and the latter should not prevent the responsible innovation of nanotechnology in dentistry. However, the clinical safety regulations for dental materials have not been specifically updated for ENMs, and some guidance on occupational health for practitioners is also needed. Knowledge gaps for future research include the formation of protein corona in the oral cavity, ENM diffusion through clinically relevant biofilms, and mechanistic investigations on how ENMs strengthen the tooth structure

Mechanical, antibacterial and bond strength properties of nano-titanium-enriched glass ionomer cement

The use of nanoparticles (NPs) has become a significant area of research in Dentistry. Objective The aim of this study was to investigate the physical, antibacterial activity and bond strength properties of conventional base, core build and restorative of glass ionomer cement (GIC) compared to GIC supplemented with titanium dioxide (TiO2) nanopowder at 3% and 5% (w/w). Material and Methods Vickers microhardness was estimated with diamond indenter. Compressive and flexural strengths were analyzed in a universal testing machine. Specimens were bonded to enamel and dentine, and tested for shear bond strength in a universal testing machine. Specimens were incubated with S. mutans suspension for evaluating antibacterial activity. Surface analysis of restorative conventional and modified GIC was performed with SEM and EDS. The analyses were carried out with Kolmogorov-Smirnov, ANOVA (post-hoc), Tukey test, Kruskal-Wallis, and Mann Whitney. Results Conventional GIC and GIC modified with TiO2 nanopowder for the base/liner cement and core build showed no differences for mechanical, antibacterial, and shear bond properties (p>0.05). In contrast, the supplementation of TiO2 NPs to restorative GIC significantly improved Vickers microhardness (p<0.05), flexural and compressive strength (p<0.05), and antibacterial activity (p<0.001), without interfering with adhesion to enamel and dentin. Conclusion GIC supplemented with TiO2 NPs (FX-II) is a promising material for restoration because of its potential antibacterial activity and durable restoration to withstand the mastication force

Calcium release and pH-characteristics of calcium hydroxide plus points

Aim To evaluate calcium ion release and pH-characteristics of calcium hydroxide plus points (CHPP), conventional calcium hydroxide points (CHP, both Coltene/Whaledent, Langenau, Germany) and aqueous calcium hydroxide suspension (CHS) (Calxyl, OCO, Dirmstein, Germany). Methodology Ten CHPP or CHP of size 50 were immersed into 5 mL isotonic sodium chloride solution. Conventional Ca(OH)(2)-free gutta-percha points served as negative control. Calcium release was measured up to 44 days by means of complexometric titration. Time dependent pH behaviour of all points in comparison with CHS was determined immersing 30 points of size 50 into 2.3 mL 0.9% wt NaCl-solution at time intervals of 0.5-72 h by a microelectrode measuring chain and a pH-meter. The surface morphologies of new and used gutta-percha points were evaluated qualitatively under a scanning electron microscope. Statistical evaluation was carried out using Kolmogorov-Smirnov-tests, Mann-Whitney-tests and multifactorial ANOVA. Results For CHPP, a threefold greater calcium release was measured compared with CHP. Both types of points as well as CHS showed a maximum pH of approximately 12. Differences between groups were statistically significant for calcium release and pH (multifactorial ANOVA; P 11 within 3 min. CHPP had a greater release of Ca2+ compared with CHP